SKShota Kukimoto
Shota Kukimoto
*This is an algorithmically generated author record based on publicly available information.
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Shota Kukimoto has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Susumu Goto
The University of Osaka
2 shared publications - Daiki Watanabe
Department of Mechanical Science and Bioengineering, Graduate School of Engineering Science, The University of Osaka, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531, Japan
1 shared publication - Haruka Ohyama
Graduate School of Engineering Science, Osaka University 1 , 1-3 Machikaneyama, Toyonaka, Osaka 560-8531, Japan
1 shared publication - Kazuo Matsuyama
Open Innovation Institute, Kyoto University 3 , Kyoto-daigaku-katsura, Nishikyo, Kyoto 615-8530, Japan
1 shared publication - Keiichi Onoda
R&D, Processing Development Research, Kao Corporation 4 , Minato, Wakayama 640-8580, Japan
1 shared publication - Kento Eguchi
Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama, Toyonaka, Osaka 560-8531, Japan
1 shared publication
Latest Publications
- Open Access
- 28 February 2026
- Published by Elsevier in International Journal of Pharmaceutics
- Vol. 694, 126732
Shear flow during reciprocal shaking does not disrupt protein films at the solid–liquid interface
- 28 February 2026
- Published by Elsevier in International Journal of Pharmaceutics
- Vol. 694, 126732
Open AccessShear flow during reciprocal shaking does not disrupt protein films at the solid–liquid interface
- 1 March 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (3)
Precessing cylinder as high-shear-rate mixer: Application to emulsification
Through laboratory experiments of oil-in-water emulsification, we show that we can construct a high-shear-rate mixer (precession mixer) by using the precession of a cylindrical container without any mixing blades. For high-shear-rate mixing, a container with a larger diameter and its faster spin are preferable so that the wall velocity becomes large enough. Then, the emulsification is most efficient when we set the Poincar\'e number $Po=\Omega_p/\Omega_s$, which is the ratio of the spin and precession rotation speeds, about $0.2$--$0.3$. When $Po$ is smaller than these values, shear rates in the mixer get much lower, though mixing in the bulk of the container is enhanced. On the other hand, when $Po$ is larger, shear rates near the cylindrical wall get higher but mixing in the bulk drastically declines. Through our systematic parameter survey for efficient emulsification by the precession mixer, we have also discovered an experimental law describing the maximum shear rate in the mixer. Since we can use it to appropriately choose the driving conditions of the mixer according to the properties of the materials to be mixed, this experimental law gives useful information for the practical use of the mixer.- 1 March 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (3)
Precessing cylinder as high-shear-rate mixer: Application to emulsification
Through laboratory experiments of oil-in-water emulsification, we show that we can construct a high-shear-rate mixer (precession mixer) by using the precession of a cylindrical container without any mixing blades. For high-shear-rate mixing, a container with a larger diameter and its faster spin are preferable so that the wall velocity becomes large enough. Then, the emulsification is most efficient when we set the Poincar\'e number $Po=\Omega_p/\Omega_s$, which is the ratio of the spin and precession rotation speeds, about $0.2$--$0.3$. When $Po$ is smaller than these values, shear rates in the mixer get much lower, though mixing in the bulk of the container is enhanced. On the other hand, when $Po$ is larger, shear rates near the cylindrical wall get higher but mixing in the bulk drastically declines. Through our systematic parameter survey for efficient emulsification by the precession mixer, we have also discovered an experimental law describing the maximum shear rate in the mixer. Since we can use it to appropriately choose the driving conditions of the mixer according to the properties of the materials to be mixed, this experimental law gives useful information for the practical use of the mixer.