Alessandro Castorina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alessandro Castorina has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Giuseppe Palmisano
Dipartimento di Ingegneria Elettrica Elettronica e Informatica (DIEEI), University of Catania, 95125 Catania, Italy
8 shared publications - Alessandro Parisi
STMicroelectronics, 95121 Catania, Italy
5 shared publications - Giuseppe Papotto
STMicroelectronics, 95121 Catania, Italy
5 shared publications - Nunzio Spina
STMicroelectronics, 95121 Catania, Italy
5 shared publications - Alessandro Finocchiaro
STMicroelectronics, 95121 Catania, Italy
3 shared publications - Claudio Nocera
STMicroelectronics, 95121 Catania, Italy
3 shared publications
Latest Publications
- Open Access
- 17 November 2026
- Published by MDPI AG in Electronics
- Vol. 15 (22) , 5342
An 868/915 MHz Transmitter in 90 nm BCD Technology for Embedded Wireless Communication in Smart-Power ICs
This paper presents a dual-band sub-GHz transmitter in a 90 nm BCD technology proposing circuit solutions that enable wireless connectivity in a non-RF platform. The proposed device is meant to be a first demonstrator of a monolithic I/Q RF front-end to be embedded in smart-power ICs. It includes a 2 GHz voltage-controlled oscillator (VCO) exploiting a complementary cross-coupled LC-tank topology with a digitally controlled capacitor bank for coarse tuning and an NMOS varactor for fine tuning to achieve wide tuning range while simultaneously limiting the VCO frequency gain for an optimized trade-off between phase noise performance and current consumption. The VCO drives a divide-by-two stage, which simultaneously provides I/Q signals and the RF carrier for the output buffer. It exhibits a tuning range spanning from 1.63 GHz to 1.98 GHz, which allows covering both EU and US ISM bands at 868 MHz and 915 MHz, respectively, and draws 2 mA from the 1.2 V supply voltage. The measured phase noise performance is as low as −110 dBc/Hz and −111 dBc/Hz at 1 MHz offset from the 1.74 GHz and 1.83 GHz oscillation frequencies, respectively. After the divide-by-two operation the phase noise of the corresponding transmitted carrier scales down to −116 dBc/Hz and −117 dBc/Hz at 1 MHz frequency offset from 868 MHz and 915 MHz, respectively. The RF buffer delivers through an external matching network of 3.6 dBm of output power to the 50 Ω antenna, enabling short-range wireless connectivity in smart-power platforms with a low-cost implementation.
- 17 November 2026
- Published by MDPI AG in Electronics
- Vol. 15 (22) , 5342
Open AccessAn 868/915 MHz Transmitter in 90 nm BCD Technology for Embedded Wireless Communication in Smart-Power ICs
This paper presents a dual-band sub-GHz transmitter in a 90 nm BCD technology proposing circuit solutions that enable wireless connectivity in a non-RF platform. The proposed device is meant to be a first demonstrator of a monolithic I/Q RF front-end to be embedded in smart-power ICs. It includes a 2 GHz voltage-controlled oscillator (VCO) exploiting a complementary cross-coupled LC-tank topology with a digitally controlled capacitor bank for coarse tuning and an NMOS varactor for fine tuning to achieve wide tuning range while simultaneously limiting the VCO frequency gain for an optimized trade-off between phase noise performance and current consumption. The VCO drives a divide-by-two stage, which simultaneously provides I/Q signals and the RF carrier for the output buffer. It exhibits a tuning range spanning from 1.63 GHz to 1.98 GHz, which allows covering both EU and US ISM bands at 868 MHz and 915 MHz, respectively, and draws 2 mA from the 1.2 V supply voltage. The measured phase noise performance is as low as −110 dBc/Hz and −111 dBc/Hz at 1 MHz offset from the 1.74 GHz and 1.83 GHz oscillation frequencies, respectively. After the divide-by-two operation the phase noise of the corresponding transmitted carrier scales down to −116 dBc/Hz and −117 dBc/Hz at 1 MHz frequency offset from 868 MHz and 915 MHz, respectively. The RF buffer delivers through an external matching network of 3.6 dBm of output power to the 50 Ω antenna, enabling short-range wireless connectivity in smart-power platforms with a low-cost implementation.
- Open Access
- 13 November 2025
- Published by MDPI AG in Electronics
- Vol. 14 (22) , 4433
A 39 GHz Phase Shifter in 28 nm FD-SOI CMOS Technology for mm-Wave Wireless Communications
This paper presents a 0–360° phase shifter in 28 nm FD-SOI CMOS technology, suitable for radar applications and mm-wave wireless communication systems, which adopt high-efficiency transmitter architectures. It exploits a novel switching vector modulator based on a double-balanced Gilbert cell, which guarantees high-resolution phase control while exhibiting inherently high robustness against process and temperature variations. The phase control is performed by merely changing the currents in the Gilbert cells using digitally controlled current generators. The proposed phase shifter operates at 39 GHz and provides RMS phase and gain errors of 2.7–4.7° and 0.3–0.5 dB, respectively, while drawing 13 mA from a 1 V supply voltage.
- 13 November 2025
- Published by MDPI AG in Electronics
- Vol. 14 (22) , 4433
Open AccessA 39 GHz Phase Shifter in 28 nm FD-SOI CMOS Technology for mm-Wave Wireless Communications
This paper presents a 0–360° phase shifter in 28 nm FD-SOI CMOS technology, suitable for radar applications and mm-wave wireless communication systems, which adopt high-efficiency transmitter architectures. It exploits a novel switching vector modulator based on a double-balanced Gilbert cell, which guarantees high-resolution phase control while exhibiting inherently high robustness against process and temperature variations. The phase control is performed by merely changing the currents in the Gilbert cells using digitally controlled current generators. The proposed phase shifter operates at 39 GHz and provides RMS phase and gain errors of 2.7–4.7° and 0.3–0.5 dB, respectively, while drawing 13 mA from a 1 V supply voltage.
- Open Access
- 31 March 2025
- Published by MDPI AG in Electronics
- Vol. 14 (7) , 1403
Three-Channel Fully Integrated Galvanic Isolation Interface in GaN Technology
This paper presents a three-channel galvanic isolation interface in GaN technology. Driver, diagnostic, and control channels have been implemented in a two-die integrated system to perform an isolation interface for a high-performance power switching system. Chip-to-chip communication has been used, which is based on planar micro-antennas with on–off keying modulated RF carriers. This approach provides a high isolation rating by properly setting the distance between chips. Various innovation aspects are adopted with respect to previously published works. They mainly involve the receiver robustness thanks to the switched-capacitor bias control, a bidirectional data channel implementation for power section diagnostic, and a duty cycle distortion compensation for accurate PWM signal. Driver and control channels use RF carriers of about 2 GHz and 0.9 GHz and achieve 2 MHz and 0.5 MHz measured pulse width modulation signals, respectively. The bidirectional channel adopts an RF carrier of about 400 MHz and exhibits a maximum measured data rate as high as 10 Mb/s. Thanks to the extensive use of switched-capacitor circuit solutions, well-controlled behavior is achieved against the large process tolerances and temperature drifts of the GaN technology. The isolation interface is supplied at 6 V and occupies a die area of 7.6 mm2 for each chip.
- 31 March 2025
- Published by MDPI AG in Electronics
- Vol. 14 (7) , 1403
Open AccessThree-Channel Fully Integrated Galvanic Isolation Interface in GaN Technology
This paper presents a three-channel galvanic isolation interface in GaN technology. Driver, diagnostic, and control channels have been implemented in a two-die integrated system to perform an isolation interface for a high-performance power switching system. Chip-to-chip communication has been used, which is based on planar micro-antennas with on–off keying modulated RF carriers. This approach provides a high isolation rating by properly setting the distance between chips. Various innovation aspects are adopted with respect to previously published works. They mainly involve the receiver robustness thanks to the switched-capacitor bias control, a bidirectional data channel implementation for power section diagnostic, and a duty cycle distortion compensation for accurate PWM signal. Driver and control channels use RF carriers of about 2 GHz and 0.9 GHz and achieve 2 MHz and 0.5 MHz measured pulse width modulation signals, respectively. The bidirectional channel adopts an RF carrier of about 400 MHz and exhibits a maximum measured data rate as high as 10 Mb/s. Thanks to the extensive use of switched-capacitor circuit solutions, well-controlled behavior is achieved against the large process tolerances and temperature drifts of the GaN technology. The isolation interface is supplied at 6 V and occupies a die area of 7.6 mm2 for each chip.
- Open Access
- 29 March 2025
- Published by MDPI AG in Electronics
- Vol. 14 (7) , 1368
A Control Technique for Galvanically Isolated DC–DC Converters with a Single Channel
This paper presents an on–off power control technique for galvanically isolated dc–dc converters, which implements a feedback control loop for power regulation on the same isolation transformer used for power transfer. To this aim, the power oscillator is controlled with a PWM scheme, and the control signal is transmitted through the galvanic barrier by using an ASK modulation that acts on the secondary winding of the isolation transformer. The key building block of the proposed architecture is a PLL that allows the reconstruction of the PWM control signal when the power oscillator is turned off and data transmission is disabled. The effectiveness of the proposed power control architecture is validated by designing an isolated dc–dc converter based on a thick polyimide transformer. It complies with reinforced isolation while addressing the power requirements of applications such as low-power sensor interfaces, medical devices, and housekeeping power, e.g., gate drivers or controllers for power converters. At a 20 V output voltage, 110 mW isolated output power is delivered. The dc–dc converter also provides PWM power regulation against PVT variations.
- 29 March 2025
- Published by MDPI AG in Electronics
- Vol. 14 (7) , 1368
Open AccessA Control Technique for Galvanically Isolated DC–DC Converters with a Single Channel
This paper presents an on–off power control technique for galvanically isolated dc–dc converters, which implements a feedback control loop for power regulation on the same isolation transformer used for power transfer. To this aim, the power oscillator is controlled with a PWM scheme, and the control signal is transmitted through the galvanic barrier by using an ASK modulation that acts on the secondary winding of the isolation transformer. The key building block of the proposed architecture is a PLL that allows the reconstruction of the PWM control signal when the power oscillator is turned off and data transmission is disabled. The effectiveness of the proposed power control architecture is validated by designing an isolated dc–dc converter based on a thick polyimide transformer. It complies with reinforced isolation while addressing the power requirements of applications such as low-power sensor interfaces, medical devices, and housekeeping power, e.g., gate drivers or controllers for power converters. At a 20 V output voltage, 110 mW isolated output power is delivered. The dc–dc converter also provides PWM power regulation against PVT variations.
- Open Access
- 28 May 2024
- Published by MDPI AG in Electronics
- Vol. 13 (11) , 2104
CMOS IC Solutions for the 77 GHz Radar Sensor in Automotive Applications
This paper presents recent results on CMOS integrated circuits for automotive radar sensor applications in the 77 GHz frequency band. It is well demonstrated that nano-scale CMOS technologies are the best solution for the implementation of low-cost and high-performance mm-wave radar sensors since they provide high integration level besides supporting high-speed digital processing. The present work is mainly focused on the RF front-end and summarizes the most stringent requirements of both short/medium- and long-range radar applications. After a brief introduction of the adopted technology, the paper addresses the critical building blocks of the receiver and transmitter chain while discussing crucial design aspects to meet the final performance. Specifically, effective circuit topologies are presented, which concern mixer, variable-gain amplifier, and filter for the receiver, as well as frequency doubler and power amplifier for the transmitter. Moreover, a voltage-controlled oscillator for a PLL efficiently covering the two radar bands is described. Finally, the circuit description is accompanied by experimental results of an integrated implementation in a 28 nm fully depleted silicon-on-insulator CMOS technology.
- 28 May 2024
- Published by MDPI AG in Electronics
- Vol. 13 (11) , 2104
Open AccessCMOS IC Solutions for the 77 GHz Radar Sensor in Automotive Applications
This paper presents recent results on CMOS integrated circuits for automotive radar sensor applications in the 77 GHz frequency band. It is well demonstrated that nano-scale CMOS technologies are the best solution for the implementation of low-cost and high-performance mm-wave radar sensors since they provide high integration level besides supporting high-speed digital processing. The present work is mainly focused on the RF front-end and summarizes the most stringent requirements of both short/medium- and long-range radar applications. After a brief introduction of the adopted technology, the paper addresses the critical building blocks of the receiver and transmitter chain while discussing crucial design aspects to meet the final performance. Specifically, effective circuit topologies are presented, which concern mixer, variable-gain amplifier, and filter for the receiver, as well as frequency doubler and power amplifier for the transmitter. Moreover, a voltage-controlled oscillator for a PLL efficiently covering the two radar bands is described. Finally, the circuit description is accompanied by experimental results of an integrated implementation in a 28 nm fully depleted silicon-on-insulator CMOS technology.
- Open Access
- 9 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 32 (8) , 1389-1399
A Three-Channel Package-Scale Galvanic Isolation Interface for Wide Bandgap Gate Drivers
This article presents the design of a three-channel package-scale galvanic isolation interface for SiC and GaN power switching converters. The isolation interface consists of two side-by-side co-packaged chips fabricated in a low-cost 0.32- $\mu$ m bipolar CMOS–DMOS (BCD) technology and includes three isolation data channels based on RF-coupled integrated microantennas. The isolation interface provides a channel for the gate driver control, a bidirectional channel for diagnostic, and a channel for the isolated power supply control. They use on–off keying (OOK)-modulated RF carriers of 1.5, 0.5, and 1.5 GHz, respectively. The galvanic isolation interface provides a maximum signal rate of 2 and 1.9 MHz for the driver and the power control channels, respectively, whereas the diagnostic channel guarantees half-duplex bidirectional communication up to 15 MHz. Thanks to the package-scale isolation approach, both reinforced galvanic isolation and first-rate common-mode transient immunity (CMTI) are achieved. High immunity to adjacent channel crosstalk is guaranteed by using channel frequency/physical separation. To best of the authors’ knowledge, this is the first implementation of a package-scale galvanic isolation interface with three independent communication channels, including a bidirectional channel, in silicon technology.
- 9 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 32 (8) , 1389-1399
Open AccessA Three-Channel Package-Scale Galvanic Isolation Interface for Wide Bandgap Gate Drivers
This article presents the design of a three-channel package-scale galvanic isolation interface for SiC and GaN power switching converters. The isolation interface consists of two side-by-side co-packaged chips fabricated in a low-cost 0.32- $\mu$ m bipolar CMOS–DMOS (BCD) technology and includes three isolation data channels based on RF-coupled integrated microantennas. The isolation interface provides a channel for the gate driver control, a bidirectional channel for diagnostic, and a channel for the isolated power supply control. They use on–off keying (OOK)-modulated RF carriers of 1.5, 0.5, and 1.5 GHz, respectively. The galvanic isolation interface provides a maximum signal rate of 2 and 1.9 MHz for the driver and the power control channels, respectively, whereas the diagnostic channel guarantees half-duplex bidirectional communication up to 15 MHz. Thanks to the package-scale isolation approach, both reinforced galvanic isolation and first-rate common-mode transient immunity (CMTI) are achieved. High immunity to adjacent channel crosstalk is guaranteed by using channel frequency/physical separation. To best of the authors’ knowledge, this is the first implementation of a package-scale galvanic isolation interface with three independent communication channels, including a bidirectional channel, in silicon technology.
- Open Access
- 9 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 126892-126899
GaN Monolithic PWM Generator With Dynamic Offset Compensation
The first fully integrated GaN pulse width modulation (PWM) generator for power conversion applications is presented in this paper. The solution is implemented in a 0.5-μm technology, avoiding additional pins and external capacitors for sawtooth signal generation while providing high accuracy. Indeed, the large GaN process spreads are addressed through an innovative dynamic offset compensation approach whose clock signal takes advantage of the PWM signal itself. The proposed PWM generator adopts a 6-V power supply and includes a 25 digital divider to set the PWM frequency at 500 kHz and the minimum and maximum duty cycles at 6% and 94%, respectively. Experimental results on integrated prototypes validated the correct circuit functionality over the temperature range from -40°C to 120°C. As a main achievement, this work demonstrates effective all-GaN integration of complex mixed analog and digital circuits, thus representing a significant advancement in the approaches to overcome the main limitations of GaN devices and enable fully integrated signal processing implementation.
- 9 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 126892-126899
Open AccessGaN Monolithic PWM Generator With Dynamic Offset Compensation
The first fully integrated GaN pulse width modulation (PWM) generator for power conversion applications is presented in this paper. The solution is implemented in a 0.5-μm technology, avoiding additional pins and external capacitors for sawtooth signal generation while providing high accuracy. Indeed, the large GaN process spreads are addressed through an innovative dynamic offset compensation approach whose clock signal takes advantage of the PWM signal itself. The proposed PWM generator adopts a 6-V power supply and includes a 25 digital divider to set the PWM frequency at 500 kHz and the minimum and maximum duty cycles at 6% and 94%, respectively. Experimental results on integrated prototypes validated the correct circuit functionality over the temperature range from -40°C to 120°C. As a main achievement, this work demonstrates effective all-GaN integration of complex mixed analog and digital circuits, thus representing a significant advancement in the approaches to overcome the main limitations of GaN devices and enable fully integrated signal processing implementation.
- Open Access
- 29 August 2023
- Published by MDPI AG in Electronics
- Vol. 12 (17) , 3639
A Ka-Band Doherty Power Amplifier in a 150 nm GaN-on-SiC Technology for 5G Applications
This paper presents a Ka-band three-stage power amplifier for 5G communications, which has been implemented in a 150 nm GaN-on-SiC technology and adopts a Doherty architecture. The amplifier is made up of a 50 Ω input buffer, which drives a power splitter, thanks to which it delivers its output power to the two power amplifier units of the Doherty topology, namely the main and auxiliary amplifier. Finally, the outputs of the two power amplifiers are properly arranged in a current combining scheme that enables the typical load modulation of the Doherty architecture, alongside allowing power combining at the final output. The proposed amplifier achieves a small signal gain of around 30 dB at 27 GHz, while providing a saturated output power of 32 dBm, with a power-added efficiency (PAE) as high as 26% and 18% at peak and 6 dB output power back-off, respectively.
- 29 August 2023
- Published by MDPI AG in Electronics
- Vol. 12 (17) , 3639
Open AccessA Ka-Band Doherty Power Amplifier in a 150 nm GaN-on-SiC Technology for 5G Applications
This paper presents a Ka-band three-stage power amplifier for 5G communications, which has been implemented in a 150 nm GaN-on-SiC technology and adopts a Doherty architecture. The amplifier is made up of a 50 Ω input buffer, which drives a power splitter, thanks to which it delivers its output power to the two power amplifier units of the Doherty topology, namely the main and auxiliary amplifier. Finally, the outputs of the two power amplifiers are properly arranged in a current combining scheme that enables the typical load modulation of the Doherty architecture, alongside allowing power combining at the final output. The proposed amplifier achieves a small signal gain of around 30 dB at 27 GHz, while providing a saturated output power of 32 dBm, with a power-added efficiency (PAE) as high as 26% and 18% at peak and 6 dB output power back-off, respectively.
- Open Access
- 29 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (10) , 4577-4587
A W-Band Transmitter for Automotive Radar Sensors in 28-nm FD-SOI CMOS
This article presents a 77-GHz transmitter (TX) in a 28-nm fully depleted silicon-on-insulator CMOS technology for automotive radar applications. The circuit has been designed to simultaneously fulfill both short-/medium-range (S/MR) and long-range (LR) operations. It exploits an LO frequency doubling architecture, which allows preventing voltage-controlled oscillator (VCO) pulling effects for improved phase noise (PN) performance. The proposed TX comprises a 38-GHz VCO driving a frequency doubler and then a current-combining two-path power amplifier. The VCO takes advantage of a novel tank architecture to cope S/MR and LR requirements with an effective and silicon area-saving solution. The proposed TX also features a feedback loop that allows properly setting the power delivered to the output load. It exhibits a 5-GHz bandwidth, ranging from 76 to 81 GHz, with a PN performance as low as $-$ 93 dBc/Hz at a 1-MHz offset frequency from a 77-GHz carrier. It is also able to deliver a maximum output power as high as 17.5 dBm with a dynamic control range of around 13 dB. The overall power consumption is 351 mW.
- 29 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (10) , 4577-4587
Open AccessA W-Band Transmitter for Automotive Radar Sensors in 28-nm FD-SOI CMOS
This article presents a 77-GHz transmitter (TX) in a 28-nm fully depleted silicon-on-insulator CMOS technology for automotive radar applications. The circuit has been designed to simultaneously fulfill both short-/medium-range (S/MR) and long-range (LR) operations. It exploits an LO frequency doubling architecture, which allows preventing voltage-controlled oscillator (VCO) pulling effects for improved phase noise (PN) performance. The proposed TX comprises a 38-GHz VCO driving a frequency doubler and then a current-combining two-path power amplifier. The VCO takes advantage of a novel tank architecture to cope S/MR and LR requirements with an effective and silicon area-saving solution. The proposed TX also features a feedback loop that allows properly setting the power delivered to the output load. It exhibits a 5-GHz bandwidth, ranging from 76 to 81 GHz, with a PN performance as low as $-$ 93 dBc/Hz at a 1-MHz offset frequency from a 77-GHz carrier. It is also able to deliver a maximum output power as high as 17.5 dBm with a dynamic control range of around 13 dB. The overall power consumption is 351 mW.