Mahaboob Basha Shaik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Mahaboob Basha Shaik has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
M.M. Basha
Department of Mechanical engineering , Indian Institute of Technology Tirupati, Tirupati, India
5 shared publicationsM.R. Sankar
4 shared publications- Mamilla Ravi Sankar
Department of Mechanical Engineering, Indian Institute of Technology, Tirupati, India
4 shared publications H.K. Dave
2 shared publicationsH.V. Patel
2 shared publicationsN. Venkaiah
2 shared publications
Latest Publications
- 17 August 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (4) , 2133-2160
Experimental investigation and prediction of surface roughness in abrasive flow finishing of additive manufactured pure copper
- 17 August 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (4) , 2133-2160
Experimental investigation and prediction of surface roughness in abrasive flow finishing of additive manufactured pure copper
- 9 August 2023
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 39 (3) , 291-309
A review on severe plastic deformation based post-processes for metal additive manufactured complex features
- 9 August 2023
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 39 (3) , 291-309
A review on severe plastic deformation based post-processes for metal additive manufactured complex features
- 1 January 2022
- Published by Springer Nature
- p. 23-36
A Preliminary Investigation on Different Tool Wears in Sustainable Electrical Discharge Machining of Ti-6Al-4V
- 1 January 2022
- Published by Springer Nature
- p. 23-36
A Preliminary Investigation on Different Tool Wears in Sustainable Electrical Discharge Machining of Ti-6Al-4V
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 38, 2249-2255
Experimental investigation on the quality of electric discharge machined Ti-6Al-4V using bio-oil and biodiesel
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 38, 2249-2255
Experimental investigation on the quality of electric discharge machined Ti-6Al-4V using bio-oil and biodiesel
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 38, 2102-2109
Experimental investigation of jatropha curcas bio-oil and biodiesel in electric discharge machining of Ti-6Al-4V
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 38, 2102-2109
Experimental investigation of jatropha curcas bio-oil and biodiesel in electric discharge machining of Ti-6Al-4V
- 20 December 2020
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 8 (sup1) , 37-48
State of Art on Development of Diamond Reinforced Tungsten Carbide based Cutting Tool by Powder Metallurgy Routes
Removing material from any workpiece is done using either a single point or multi-point cutting tool in the machining process for achieving the desired shape. The 15–20% of total energy is consumed to avoid the sliding friction at the flank and rake faces of the tool. Owing to overcome frictional/wear problems, two categories, namely cutting fluids and tool improvements, are generally employed in the machining process. Cutting fluid creates some issues such as thermal cracking by reusing the same fluid and environmental pollution whenever dumping. In contrast, material selection before manufacturing a cutting tool is the best solution for tool improvement. In order that this review work shows the fabrication of diamond reinforced tungsten carbide-based cutting tool by different powder metallurgy techniques such as the high pressure- high-temperature technique, spark plasma sintering and pulse plasma sintering techniques. In addition, the adverse effects of graphitisation that occurred in these techniques are discussed in detail. Finally, this work concludes with a challenging task, such as strengthening the chemical bond between the diamond and tungsten carbide in low-pressure techniques like spark plasma sintering and pulse plasma sintering.
- 20 December 2020
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 8 (sup1) , 37-48
State of Art on Development of Diamond Reinforced Tungsten Carbide based Cutting Tool by Powder Metallurgy Routes
Removing material from any workpiece is done using either a single point or multi-point cutting tool in the machining process for achieving the desired shape. The 15–20% of total energy is consumed to avoid the sliding friction at the flank and rake faces of the tool. Owing to overcome frictional/wear problems, two categories, namely cutting fluids and tool improvements, are generally employed in the machining process. Cutting fluid creates some issues such as thermal cracking by reusing the same fluid and environmental pollution whenever dumping. In contrast, material selection before manufacturing a cutting tool is the best solution for tool improvement. In order that this review work shows the fabrication of diamond reinforced tungsten carbide-based cutting tool by different powder metallurgy techniques such as the high pressure- high-temperature technique, spark plasma sintering and pulse plasma sintering techniques. In addition, the adverse effects of graphitisation that occurred in these techniques are discussed in detail. Finally, this work concludes with a challenging task, such as strengthening the chemical bond between the diamond and tungsten carbide in low-pressure techniques like spark plasma sintering and pulse plasma sintering.
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 26, 2608-2615
State of art on wire feed additive manufacturing of Ti-6Al-4V alloy
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 26, 2608-2615
State of art on wire feed additive manufacturing of Ti-6Al-4V alloy
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 26, 2047-2054
Laser polishing of 3D printed metallic components: A review on surface integrity
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 26, 2047-2054
Laser polishing of 3D printed metallic components: A review on surface integrity
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 26, 542-548
Past and current trends in electric discharge based machining of Silicon Carbide
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 26, 542-548
Past and current trends in electric discharge based machining of Silicon Carbide