Azuka Affam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Azuka Affam has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Al Khalid Othman
Universiti Malaysia Sarawak
3 shared publications - Norhuzaimin Julai
Universiti Malaysia Sarawak
3 shared publications - Yonis M. Yonis Buswig
Universiti Malaysia Sarawak
3 shared publications - Hazrul Mohamed Basri
Department of Electrical and Electronics Engineering, Faculty of Engineering, Universiti Malaysia Sarawak (UNIMAS), Kota Samarahan, Sarawak, Malaysia
2 shared publications - Kasumawati Lias
Universiti Malaysia Sarawak
2 shared publications - Shanti Faridah Salleh
Department of Chemical Engineering and Energy Sustainability, Faculty of Engineering, Universiti Malaysia Sarawak, 94300 Kota Samarahan, Sarawak, Malaysia
2 shared publications
Latest Publications
- Open Access
- 1 February 2026
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 15 (1) , 171-183
Dual axis solar tracker and monitoring system based on internet of things
In this paper, the application of internet of things (IoT) technology in development of a dual-axis solar tracking system is presented. Sting capacity of piezoelectric material is applied a footstep energy generation system. Using Arduino MEGA as the main controller for the system, light-dependent resistors (LDRs) have been used for sunlight detection and maximum light intensity. Two servo motors have been employed to rotate the solar panel towards the position of the sun as detected by the LDR. Ethernet Shield is used as an intermediary between the hardware device and the IoT monitoring system through the Cayenne platform. Alert notifications are included to inform a remote user through phone or mail (or both) when a sensor has reached a certain predefined event. There is a 21.97 increased energy output buy the proposed system as compared to the single-axis solar tracker. Further test results of the manufactured prototype indicate that solar tracker data can be transmitted simply and monitored directly online, and the solar tracker is capable of receiving commands from the IoT monitoring application.
- 1 February 2026
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 15 (1) , 171-183
Open AccessDual axis solar tracker and monitoring system based on internet of things
In this paper, the application of internet of things (IoT) technology in development of a dual-axis solar tracking system is presented. Sting capacity of piezoelectric material is applied a footstep energy generation system. Using Arduino MEGA as the main controller for the system, light-dependent resistors (LDRs) have been used for sunlight detection and maximum light intensity. Two servo motors have been employed to rotate the solar panel towards the position of the sun as detected by the LDR. Ethernet Shield is used as an intermediary between the hardware device and the IoT monitoring system through the Cayenne platform. Alert notifications are included to inform a remote user through phone or mail (or both) when a sensor has reached a certain predefined event. There is a 21.97 increased energy output buy the proposed system as compared to the single-axis solar tracker. Further test results of the manufactured prototype indicate that solar tracker data can be transmitted simply and monitored directly online, and the solar tracker is capable of receiving commands from the IoT monitoring application.
- Open Access
- 1 June 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 16 (2) , 1024-1037
Battery integrated three input high gain DC-DC converter for renewable energy sources
In this work, a battery-integrated three-input converter is proposed. The topology combines a traditional boost converter on one side with a non-coupled inductor-based buffer stage on the other side. Some merits of the converter are a high voltage gain, a high output voltage in the battery discharging mode, and a wide range of output voltage. The bidirectional port makes it attractive for renewable energy (RE) sources like solar and fuel cells. The converter can operate in three modes that are determined by the availability of RE sources and the battery state of charge (SOC). The power management algorithm enabled the converter to work in either single-input, double-input, or three-input configurations. The duty ratios of assigned power switches controlled the output voltage and the battery charge/discharge. Steady-state analyses and dynamic modeling are presented and discussed. At 12 V and 24 V input voltage, the output voltage of 315.52 V was delivered in the battery-excluded mode. The battery discharging mode delivered 311.57 V while the battery charging mode delivered 301.32 V. The proposed converter can serve low to medium power voltage/power applications. The hardware experiments verify the workings of the proposed converter.
- 1 June 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 16 (2) , 1024-1037
Open AccessBattery integrated three input high gain DC-DC converter for renewable energy sources
In this work, a battery-integrated three-input converter is proposed. The topology combines a traditional boost converter on one side with a non-coupled inductor-based buffer stage on the other side. Some merits of the converter are a high voltage gain, a high output voltage in the battery discharging mode, and a wide range of output voltage. The bidirectional port makes it attractive for renewable energy (RE) sources like solar and fuel cells. The converter can operate in three modes that are determined by the availability of RE sources and the battery state of charge (SOC). The power management algorithm enabled the converter to work in either single-input, double-input, or three-input configurations. The duty ratios of assigned power switches controlled the output voltage and the battery charge/discharge. Steady-state analyses and dynamic modeling are presented and discussed. At 12 V and 24 V input voltage, the output voltage of 315.52 V was delivered in the battery-excluded mode. The battery discharging mode delivered 311.57 V while the battery charging mode delivered 301.32 V. The proposed converter can serve low to medium power voltage/power applications. The hardware experiments verify the workings of the proposed converter.
- Open Access
- 1 April 2023
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 12 (2) , 677-688
A battery integrated multiple input DC-DC boost converter
In this paper, the proposed single boost converter aims to harness more than one renewable energy (RE) input source and achieve a high voltage gain. The interleaved technique combined with voltage multiplier (VM) cells, reduced inductor current and attained high voltage transfer ratio. The boost converter possesses two unidirectional input ports and a bidirectional input port that is connected to a battery storage. The duty ratios of the power and interleaving switches are used to regulate the output voltage of the proposed converter. Three operation modes are identified, and steady state analyses of the converter are presented and discussed. The converter can store excess energy in the battery during periods of abundance and deliver power to the loads when the RE sources are low or unavailable. In addition, the output voltage is higher than that of the conventional boost converter. The converter delivered 278 V from 12 V and 24 V dual input sources. The converter operation is simulated and verified using MATLAB/Simulink.
- 1 April 2023
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 12 (2) , 677-688
Open AccessA battery integrated multiple input DC-DC boost converter
In this paper, the proposed single boost converter aims to harness more than one renewable energy (RE) input source and achieve a high voltage gain. The interleaved technique combined with voltage multiplier (VM) cells, reduced inductor current and attained high voltage transfer ratio. The boost converter possesses two unidirectional input ports and a bidirectional input port that is connected to a battery storage. The duty ratios of the power and interleaving switches are used to regulate the output voltage of the proposed converter. Three operation modes are identified, and steady state analyses of the converter are presented and discussed. The converter can store excess energy in the battery during periods of abundance and deliver power to the loads when the RE sources are low or unavailable. In addition, the output voltage is higher than that of the conventional boost converter. The converter delivered 278 V from 12 V and 24 V dual input sources. The converter operation is simulated and verified using MATLAB/Simulink.