Qi Jia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Qi Jia has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Alaleh Ziagharib
Department of Civil, Environmental and Natural Resources Engineering, Luleå University of Technology, Luleå, Sweden
4 shared publications - Christian Maurice
Department of Civil, Environmental and Natural Resources Engineering, Luleå University of Technology, Luleå, Sweden
4 shared publications - Jan Laue
Department of Civil, Environmental and Natural Resources Engineering, Lulea University of Technology, 97187 Lulea, Sweden
4 shared publications - Josef Macsik
Ecoloop, Stockholm, Sweden
4 shared publications - Hans Mattsson
Department of Civil, Environmental and Natural Resources Engineering, Luleå University of Technology, Luleå, Sweden
1 shared publication - Tan Manh Do
Hanoi University of Mining and Geology
1 shared publication
Latest Publications
- Open Access
- 19 February 2026
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 85 (3) , 155
Factors influencing the effectiveness of acid sulfate soil stabilization with cement-based binders
Sulfide-rich soils (also called potential acid sulfate soil), with their sulfur content, and potential to generate acidity, pose challenges for construction due to low bearing capacity, shear strength, and their acidification potential. This study compares the effectiveness of Portland cement and Multicem binders in stabilizing these soils by analyzing unconfined compressive strength (UCS), porosity, pH changes, and strain behavior. Four soil samples with varying state of oxidation, pH, sulfur content, and water content were treated with binders at different dosages and analyzed after 28 days of curing. The results demonstrate that binder type and dosage, initial pH, and soil composition together significantly influence stabilization performance. Portland cement achieved higher UCS values across all samples, particularly in soils with low pH, due to its high alkalinity and facilitation of hydration reactions. In contrast, Multicem achieved acceptable UCS in soils with moderate initial pH, as its slower hydration limited its effectiveness in highly acidic conditions. Porosity reduction in stabilized samples correlated with increased binder content. Strain behavior exhibited an inverse relationship with UCS. Higher UCS samples showed reduced strain, indicating increased stiffness. However, in oxidized and highly acidic sulfate soils, such as Sunderbyn, UCS gains were limited, suggesting that extreme pH conditions inhibit binder effectiveness. The study offers practical guidance for optimizing binder selection and application strategies, especially for the treatment of acid sulfate-rich soils in geotechnical engineering. Future research should prioritize the assessment of durability, stability and performance under varied environmental stresses to ensure sustainable solutions.
- 19 February 2026
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 85 (3) , 155
Open AccessFactors influencing the effectiveness of acid sulfate soil stabilization with cement-based binders
Sulfide-rich soils (also called potential acid sulfate soil), with their sulfur content, and potential to generate acidity, pose challenges for construction due to low bearing capacity, shear strength, and their acidification potential. This study compares the effectiveness of Portland cement and Multicem binders in stabilizing these soils by analyzing unconfined compressive strength (UCS), porosity, pH changes, and strain behavior. Four soil samples with varying state of oxidation, pH, sulfur content, and water content were treated with binders at different dosages and analyzed after 28 days of curing. The results demonstrate that binder type and dosage, initial pH, and soil composition together significantly influence stabilization performance. Portland cement achieved higher UCS values across all samples, particularly in soils with low pH, due to its high alkalinity and facilitation of hydration reactions. In contrast, Multicem achieved acceptable UCS in soils with moderate initial pH, as its slower hydration limited its effectiveness in highly acidic conditions. Porosity reduction in stabilized samples correlated with increased binder content. Strain behavior exhibited an inverse relationship with UCS. Higher UCS samples showed reduced strain, indicating increased stiffness. However, in oxidized and highly acidic sulfate soils, such as Sunderbyn, UCS gains were limited, suggesting that extreme pH conditions inhibit binder effectiveness. The study offers practical guidance for optimizing binder selection and application strategies, especially for the treatment of acid sulfate-rich soils in geotechnical engineering. Future research should prioritize the assessment of durability, stability and performance under varied environmental stresses to ensure sustainable solutions.
- Open Access
- 29 March 2025
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 43 (4) , 1
Correction: Predictive Pattern of Undrained Shear Strength in Stabilized Sulfur Rich Silty Soil Based on Binder and Initial Mixing Water Content
- 29 March 2025
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 43 (4) , 1
Open AccessCorrection: Predictive Pattern of Undrained Shear Strength in Stabilized Sulfur Rich Silty Soil Based on Binder and Initial Mixing Water Content
- Open Access
- 4 June 2024
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 42 (6) , 5033-5050
Predictive Pattern of Undrained Shear Strength in Stabilized Sulfur Rich Silty Soil Based on Binder and Initial Mixing Water Content
A laboratory investigation was conducted to identify principal variables-initial mixing water content, porosity, and binder content- impacting undrained shear strength (qu) of stabilized sulfur-rich silty soil. An equation for predicting qu of stabilized soil was established based on the experimental data. Initially, samples were prepared with soils sample with different initial water and binder contents. Multicem, a binder consisting of a mix of cement and cement kiln dust, was added to the samples. Three different percentages of Multicem were mixed at five different soil water contents to measure qu of stabilized mixtures to understand how water content and porosity levels in the samples affect the performance of the binder and their combined impact on the strength of the samples. The soil-binder mixtures were compacted and subsequently cured in laboratory-controlled environment. The prepared samples were tested in uniaxial compression test apparatus. The results evidenced that binder content and corresponding porosity affect the strength of specimens at an equal water content. The results showed that at equal initial mixing water content, the qu of a sample increased by increasing binder content. Furthermore, it was observed that increase of binder content has a reverse effect on porosity. It was appeared lowering the soil water content, initially increased the strength until an optimum water content. Further lowering water content increased the porosity and consequently decreased qu of samples. Moreover, a ratio of porosity/volumetric binder content was chosen to evaluate the impact of these two variables on strength of samples. This study showed that qu is an exponential function of porosity/binder volumetric content ratio which depends on initial mixing water content of mixtures. It was shown at water content lower than the optimum, results of stabilization are more effective than in soil at higher water contents. Therefore, reducing the water content and thereby porosity has more significant effect on improving qu than increasing the binder content.
- 4 June 2024
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 42 (6) , 5033-5050
Open AccessPredictive Pattern of Undrained Shear Strength in Stabilized Sulfur Rich Silty Soil Based on Binder and Initial Mixing Water Content
A laboratory investigation was conducted to identify principal variables-initial mixing water content, porosity, and binder content- impacting undrained shear strength (qu) of stabilized sulfur-rich silty soil. An equation for predicting qu of stabilized soil was established based on the experimental data. Initially, samples were prepared with soils sample with different initial water and binder contents. Multicem, a binder consisting of a mix of cement and cement kiln dust, was added to the samples. Three different percentages of Multicem were mixed at five different soil water contents to measure qu of stabilized mixtures to understand how water content and porosity levels in the samples affect the performance of the binder and their combined impact on the strength of the samples. The soil-binder mixtures were compacted and subsequently cured in laboratory-controlled environment. The prepared samples were tested in uniaxial compression test apparatus. The results evidenced that binder content and corresponding porosity affect the strength of specimens at an equal water content. The results showed that at equal initial mixing water content, the qu of a sample increased by increasing binder content. Furthermore, it was observed that increase of binder content has a reverse effect on porosity. It was appeared lowering the soil water content, initially increased the strength until an optimum water content. Further lowering water content increased the porosity and consequently decreased qu of samples. Moreover, a ratio of porosity/volumetric binder content was chosen to evaluate the impact of these two variables on strength of samples. This study showed that qu is an exponential function of porosity/binder volumetric content ratio which depends on initial mixing water content of mixtures. It was shown at water content lower than the optimum, results of stabilization are more effective than in soil at higher water contents. Therefore, reducing the water content and thereby porosity has more significant effect on improving qu than increasing the binder content.
- Open Access
- 30 March 2023
- Published by Wiley in Advances in Civil Engineering
- Vol. 2023, 1-11
Performance of Excavated Sulfur-Rich Soil Stabilized with Binder: A Field Study of Mixing Efficiency
In this study, a mixing procedure of sulfur-rich soil and cement-based binder to enhance the soil’s unconfined compressive strength (UCS) was tested in field conditions for geotechnical applications. The focus was to evaluate uniformity of industrial size soil-binder mixture, blended by existing method. This paper outlined sampling strategy and the number of samples needed for a valid uniformity evaluation. Moreover, this study emphasized the difference between field mixing and laboratory mixture preparation by comparing UCS of stabilized soil samples in the field and UCS of corresponding samples mixed and prepared in the laboratory environment. In the field, soil and cement were blended in two to four stages with 5% and 7% cement—the percentages being based on the soil’s dry weight under field conditions. Samples were taken from the field mixtures after each stage. Since the number of samples needed to be representative of mixture characteristics for large-scale mixing is not standardized, this field experiment included two phases. The first phase was dedicated to finding a sampling strategy for a large soil pile along with measuring UCS of collected samples. In the second phase, sample collection was conducted based on the results of sampling strategy from the first phase. In the laboratory, samples with percentages of binder similar to the amount of binder in the field were also prepared. Both field and laboratory samples were prepared using the tapping method in the laboratory for UCS test. Samples were cured under similar conditions for 28 days. The results showed that the uniformity of mixture improved after each additional mixing stage. In addition, while spots with low UCS were observed in the second mixing step, these spots were eliminated in the third mixing step, and results of the UCS tests were comparatively uniform. Moreover, comparison of the samples revealed that the UCS of the laboratory mixture is higher than that of the field mixture. This showed that even though the UCS is a good standard for comparing the strength of different soils stabilized with different percentages or types of binders in the field mixing, the actual strength of the stabilized mixtures under field circumstances is lower than that in laboratory prepared mixtures.
- 30 March 2023
- Published by Wiley in Advances in Civil Engineering
- Vol. 2023, 1-11
Open AccessPerformance of Excavated Sulfur-Rich Soil Stabilized with Binder: A Field Study of Mixing Efficiency
In this study, a mixing procedure of sulfur-rich soil and cement-based binder to enhance the soil’s unconfined compressive strength (UCS) was tested in field conditions for geotechnical applications. The focus was to evaluate uniformity of industrial size soil-binder mixture, blended by existing method. This paper outlined sampling strategy and the number of samples needed for a valid uniformity evaluation. Moreover, this study emphasized the difference between field mixing and laboratory mixture preparation by comparing UCS of stabilized soil samples in the field and UCS of corresponding samples mixed and prepared in the laboratory environment. In the field, soil and cement were blended in two to four stages with 5% and 7% cement—the percentages being based on the soil’s dry weight under field conditions. Samples were taken from the field mixtures after each stage. Since the number of samples needed to be representative of mixture characteristics for large-scale mixing is not standardized, this field experiment included two phases. The first phase was dedicated to finding a sampling strategy for a large soil pile along with measuring UCS of collected samples. In the second phase, sample collection was conducted based on the results of sampling strategy from the first phase. In the laboratory, samples with percentages of binder similar to the amount of binder in the field were also prepared. Both field and laboratory samples were prepared using the tapping method in the laboratory for UCS test. Samples were cured under similar conditions for 28 days. The results showed that the uniformity of mixture improved after each additional mixing stage. In addition, while spots with low UCS were observed in the second mixing step, these spots were eliminated in the third mixing step, and results of the UCS tests were comparatively uniform. Moreover, comparison of the samples revealed that the UCS of the laboratory mixture is higher than that of the field mixture. This showed that even though the UCS is a good standard for comparing the strength of different soils stabilized with different percentages or types of binders in the field mixing, the actual strength of the stabilized mixtures under field circumstances is lower than that in laboratory prepared mixtures.
- Open Access
- 29 June 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (13) , 6044
Numerical Analysis of an Upstream Tailings Dam Subjected to Pond Filling Rates
One of the challenges in upstream tailings dam projects is to ensure the allowable rate of deposition of tailings in the pond (i.e., pond filling rate) while maintaining the stability of the dam. This is due to the fact that an upstream tailings dam is constructed by placing dikes on top of previously deposited soft tailings, which could lead to a decrease in dam stability because of the build-up of excess pore water pressure. The main purpose of this work is to investigate the effects of pond filling rates on excess pore water pressure and the stability of an upstream tailings dam by a numerical study. A finite element software was used to simulate the time-dependent pond filling process and staged dam construction under various pond filling rates. As a result, excess pore water pressure increased in each raising phase and decreased in the subsequent consolidation phase. However, some of the excess pore water pressure remained after every consolidation phase (i.e., the build-up of excess pore water pressure), which could lead to a potentially critical situation in the stability of the dam. In addition, the remaining excess pore water pressure varied depending on the pond filling rates, being larger for high filling rates and smaller for low filling rates. It is believed that the approach used in this study could be a guide for dam owners to keep a sufficiently high pond filling rate but still ensure the desirable stability of an upstream tailings dam.
- 29 June 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (13) , 6044
Open AccessNumerical Analysis of an Upstream Tailings Dam Subjected to Pond Filling Rates
One of the challenges in upstream tailings dam projects is to ensure the allowable rate of deposition of tailings in the pond (i.e., pond filling rate) while maintaining the stability of the dam. This is due to the fact that an upstream tailings dam is constructed by placing dikes on top of previously deposited soft tailings, which could lead to a decrease in dam stability because of the build-up of excess pore water pressure. The main purpose of this work is to investigate the effects of pond filling rates on excess pore water pressure and the stability of an upstream tailings dam by a numerical study. A finite element software was used to simulate the time-dependent pond filling process and staged dam construction under various pond filling rates. As a result, excess pore water pressure increased in each raising phase and decreased in the subsequent consolidation phase. However, some of the excess pore water pressure remained after every consolidation phase (i.e., the build-up of excess pore water pressure), which could lead to a potentially critical situation in the stability of the dam. In addition, the remaining excess pore water pressure varied depending on the pond filling rates, being larger for high filling rates and smaller for low filling rates. It is believed that the approach used in this study could be a guide for dam owners to keep a sufficiently high pond filling rate but still ensure the desirable stability of an upstream tailings dam.