Bin Wu

Wireless Local-Area Networks (WLANs), as a popular internet access solution, are widely used in numerous places, including enterprises, campuses, and public venues. As the number of devices increases, large-scale deployments will cause the problem of dense wireless networks, including a lot of energy consumption. Thus, the optimization of energy-efficient wireless AP devices has become a focal point of attention. To reduce energy consumption, we have proposed the active access-point (AP) configuration algorithm for WLANs using APs with a dual interface. This uses the greedy algorithm combined with the local search optimization method to find the minimum number of activated APs while satisfying the minimum throughput constraint. However, the previous algorithm basically satisfies only the average throughput among the multiple hosts associated with one AP, wherein some hosts may not reach the required one. In this paper, to overcome this limitation, we propose an enhanced active AP configuration algorithm by incorporating the throughput request satisfaction method that controls the actual throughput at the target value (target throughput) for every host by applying traffic shaping. The target throughput is calculated from the single and concurrent communicating throughput of each host based on channel occupancy time. The minimum throughput constraint will be iteratively adjusted to obtain the required target throughput and achieve the fair throughput allocation. For evaluations, we conducted simulations using the WIMNET simulator and experiments using the testbed system with a Raspberry Pi 4B for APs in four topology cases with five APs and ten hosts. The results show that the proposed method always achieved the required minimum throughput in simulations as well as in experiments, while minimizing the number of active APs. Thus, the validity and effectiveness of our proposal were confirmed.

With the wide applications of the Internet of Things (IoT) in smart home systems, IEEE 802.11n Wireless Local Area Networks (WLANs) have become a frequently chosen communication technology due to their adaptability and affordability. In a high-density network of devices such as the smart home scenerio, a host often meets interferences from other devices and unequal Received Signal Strength (RSS) from Access Points (APs). This results in throughput unfairness/insufficiency problems between hosts communicating concurrently in WLAN. Previously, we have studied the throughput request satisfaction method to address this problem. It calculates the target throughput from measured single and concurrent throughputs of hosts and controls the actual throughput at this target one by applying traffic shaping at the AP. However, the insufficiency problem of maximizing the throughput is not solved due to interferences from other hosts. In this paper, we present an extension of the throughput request satisfaction method to maximize the throughput of a high-priority host under concurrent communications. It recalculates the target throughput to increase the actual throughput as much as possible while the other hosts satisfy the least throughput. For evaluations, we conduct experiments using the test-bed system with Raspberry Pi as the AP devices in several topologies in indoor environments. The results confirm the effectiveness of our proposal.

The IEEE 802.11 wireless local-area network (WLAN) has been deployed around the globe as a major Internet access medium due to its low cost and high flexibility and capacity. Unfortunately, dense wireless networks can suffer from poor performance due to high levels of radio interference resulting from adjoining access points (APs). To address this problem, we studied the AP transmission power optimization method, which selects the maximum or minimum power supplied to each AP so that the average signal-to-interference ratio (SIR) among the concurrently communicating APs is maximized.However, this method requires measurements of receiving signal strength (RSS) under all the possible combinations of powers. It may need intolerable loads and time as the number of APs increases. It also only considers the use of channel bonding (CB), although non-CB sometimes achieves higher performance under high levels of interference. In this paper, we present an AP interface setup optimization method using the throughput estimation model for concurrently communicating APs. The proposed method selects CB or non-CB in addition to the maximum or minimum power for each AP. This model approach avoids expensive costs of RSS measurements under a number of combinations. To estimate the RSS at an AP from another AP or a host, the model needs the distance and the obstacles between them, such as walls. Then, by calculating the estimated RSS with the model and calculating the SIR from them, the AP interface setups for a lot of APs in a large-scale wireless network can be optimized on a computer in a very short time. For evaluation, we conducted extensive experiments using Raspberry Pi for APs and Linux PCs for hosts under 12 network topologies in three buildings at Okayama University, Japan, and Jatiya Kabi Kazi Nazrul Islam University, Bangladesh. The results confirm that the proposed method selects the best AP interface setup with the highest total throughput in any topology.

Currently, Internet of Things (IoT) has become common in various applications, including smart factories, smart cities, and smart homes. In them, wireless local-area networks (WLANs) are widely used due to their high-speed data transfer, flexible coverage ranges, and low costs. To enhance the performance, the WLAN configuration should be optimized in dense WLAN environments where multiple access points (APs) and hosts exist. Previously, we have studied the active AP configuration algorithm for dual interfaces using IEEE802.11n and 11ac protocols at each AP under non-channel bonding (non-CB). In this paper, we study the algorithm considering the channel bonding (CB) to enhance its capacity by bonding two channels together. To improve the throughput estimation accuracy of the algorithm, the reduction factor is introduced at contending hosts for the same AP. For evaluations, we conducted extensive experiments using the WIMENT simulator and the testbed system using Raspberry Pi 4B APs. The results show that the estimated throughput is well matched with the measured one, and the proposal achieves the higher throughput with a smaller number of active APs than the previous configurations.