Hao Mu
Hao Mu has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Bo Li
Institute of Electric Power Science of Guizhou Power Grid Co., Ltd., Guiyang 550002, China
2 shared publications - Guoyong Liu
School of Materials Science and Engineering, Chongqing University, Chongqing 400030, China
1 shared publication - Hongli Jiang
School of Intelligent Manufacturing, Zhejiang Dongfang Polytechnic, Wenzhou 325000, China
1 shared publication - Jie Bai
Institute of Electric Power Science of Guizhou Power Grid Co., Ltd., Guiyang 550002, China
1 shared publication - Lei Fan
Institute of Electric Power Science of Guizhou Power Grid Co., Ltd., Guiyang 550000, China
1 shared publication - Tao Jiang
Electric Power Research Institute of Guizhou Power Grid Co., Ltd., Guiyang 550002, China
1 shared publication
Latest Publications
- Open Access
Atomically Dispersed High-Active Site Density Copper Electrocatalyst for the Reduction of Oxygen
Enlarging the M-Nx active-site density is an effective route to enhance the ORR performance of M-N-C catalysts. In this work, a single-atom catalyst Cu–N@Cu–N–C with enlarged Cu–N4 active site density was prepared by the second doping and pyrolysis (SDP) of Cu–N–C derived from Cu-doped zeolite imidazole frameworks. The half-wave potentials of Cu–N@Cu–N–C were measured as 0.85 V in alkaline electrolyte and 0.75 V in acidic media, which was 50 mV and 60 mV higher than that of Cu–N–C, respectively. N2 adsorption–desorption isotherm curves and corresponding pore distribution analysis were used to verify the successful filling of additional Cu and N in micropores of Cu–N–C after SDP. The obvious increase in Cu contents for Cu–N@Cu–N–C (1.92 wt%) compared with Cu–N–C (0.88 wt%) tested by ICP demonstrated the successful doping of Cu into Cu–N–C. XAFS analysis confirmed the presence of Cu–N4 single-atom active centers in Cu–N@Cu–N–C. The N 1 s high-resolution XPS results proved a great increase in Cu–N4 contents from 13.15% for Cu–N–C to 18.36% for Cu–N@Cu–N–C. The enhanced ORR performance of Cu–N@Cu–N–C was attributed to the enlargement of Cu–N4 active site density, providing an effective route for the preparation of efficient and low-cost ORR catalysts.
Open AccessAtomically Dispersed High-Active Site Density Copper Electrocatalyst for the Reduction of Oxygen
Enlarging the M-Nx active-site density is an effective route to enhance the ORR performance of M-N-C catalysts. In this work, a single-atom catalyst Cu–N@Cu–N–C with enlarged Cu–N4 active site density was prepared by the second doping and pyrolysis (SDP) of Cu–N–C derived from Cu-doped zeolite imidazole frameworks. The half-wave potentials of Cu–N@Cu–N–C were measured as 0.85 V in alkaline electrolyte and 0.75 V in acidic media, which was 50 mV and 60 mV higher than that of Cu–N–C, respectively. N2 adsorption–desorption isotherm curves and corresponding pore distribution analysis were used to verify the successful filling of additional Cu and N in micropores of Cu–N–C after SDP. The obvious increase in Cu contents for Cu–N@Cu–N–C (1.92 wt%) compared with Cu–N–C (0.88 wt%) tested by ICP demonstrated the successful doping of Cu into Cu–N–C. XAFS analysis confirmed the presence of Cu–N4 single-atom active centers in Cu–N@Cu–N–C. The N 1 s high-resolution XPS results proved a great increase in Cu–N4 contents from 13.15% for Cu–N–C to 18.36% for Cu–N@Cu–N–C. The enhanced ORR performance of Cu–N@Cu–N–C was attributed to the enlargement of Cu–N4 active site density, providing an effective route for the preparation of efficient and low-cost ORR catalysts.
- Open Access
Fabrication of Slippery Surfaces on Aluminum Alloy and Its Anti-Icing Performance in Glaze Ice
Slippery liquid-infused porous surfaces (SLIPS) have received growing attention as promising icephobic materials. In this study, SLIPS were prepared on aluminum alloys by combining anodization and infusion of common silicone oil. An SLIPS with low ice-adhesion strength (6 kPa) was obtained by optimizing the anodizing time parameters (10 min). In addition, the frosting process and freezing of water droplets on the as-prepared SLIPS at −10 °C were delayed for 2000 s and 4800 s, respectively. Simultaneously, the as-prepared SLIPS also exhibited excellent anti-icing performance in glaze ice, since the supercooled water drips/ice slipped from the surface. The ice weight of the as-prepared SLIPS was significantly lower than that of the bare aluminum surface and the anti-icing-fluid-coated aluminum surface, which was reduced by 38.2%–63.6% compared with the bare aluminum surface. The ice weight increased with decreased temperature and inclination angle. This work proposes a method suitable for large-area preparation of SLIPS that achieves excellent anti-icing performance and significantly reduces the weight of glaze ice.
Open AccessFabrication of Slippery Surfaces on Aluminum Alloy and Its Anti-Icing Performance in Glaze Ice
Slippery liquid-infused porous surfaces (SLIPS) have received growing attention as promising icephobic materials. In this study, SLIPS were prepared on aluminum alloys by combining anodization and infusion of common silicone oil. An SLIPS with low ice-adhesion strength (6 kPa) was obtained by optimizing the anodizing time parameters (10 min). In addition, the frosting process and freezing of water droplets on the as-prepared SLIPS at −10 °C were delayed for 2000 s and 4800 s, respectively. Simultaneously, the as-prepared SLIPS also exhibited excellent anti-icing performance in glaze ice, since the supercooled water drips/ice slipped from the surface. The ice weight of the as-prepared SLIPS was significantly lower than that of the bare aluminum surface and the anti-icing-fluid-coated aluminum surface, which was reduced by 38.2%–63.6% compared with the bare aluminum surface. The ice weight increased with decreased temperature and inclination angle. This work proposes a method suitable for large-area preparation of SLIPS that achieves excellent anti-icing performance and significantly reduces the weight of glaze ice.