Yu Du
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yu Du has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Chang Liu
School of Mechanical Engineering Tiangong University Tianjin China
6 shared publications Tao Yang
School of Mechanical Engineering Tiangong University Tianjin China
6 shared publicationsChang Liu
School of Aeronautics and Astronautics, Tiangong University, Tianjin, China
4 shared publicationsSinan Liu
Tianjin Chengjian University
4 shared publications- Tao Yang
School of Mechanical Engineering, Tiangong University, Tianjin, China
3 shared publications Wenhui Yuan
School of Mechanical Engineering Tiangong University Tianjin China
3 shared publications
Latest Publications
- 28 August 2026
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
Investigation on hole quality in drilling of thermoplastic GF/PEEK composite using twist and double-angle-tip drills
Glass fiber reinforced polyether ether ketone (GF/PEEK) composites have been widely used in engineering manufacturing fields due to their excellent mechanical and thermal properties as well as recyclability. This study aims to investigate the drilling quality of GF/PEEK composites under varying machining conditions. Drilling experiments were carried out using twist drill and double-angle-tip drill to evaluate the effects of drilling parameters and drill geometry on drilling temperature, thrust force, as well as exit and hole wall morphology. The results show that compared with the twist drill, the thrust force and drilling temperature generated by double-angle-tip drill were reduced by 32% and 15%, respectively. The double-angle and outer-edge drill tip of the double-angle-tip drill resulted in less delamination and burr formation. SEM analysis further revealed that the double-angle-tip drill produced finer and smoother hole wall than the twist drill. These experimental findings provide valuable guidance for achieving low-damage drilling of thermoplastic composites.
- 28 August 2026
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
Investigation on hole quality in drilling of thermoplastic GF/PEEK composite using twist and double-angle-tip drills
Glass fiber reinforced polyether ether ketone (GF/PEEK) composites have been widely used in engineering manufacturing fields due to their excellent mechanical and thermal properties as well as recyclability. This study aims to investigate the drilling quality of GF/PEEK composites under varying machining conditions. Drilling experiments were carried out using twist drill and double-angle-tip drill to evaluate the effects of drilling parameters and drill geometry on drilling temperature, thrust force, as well as exit and hole wall morphology. The results show that compared with the twist drill, the thrust force and drilling temperature generated by double-angle-tip drill were reduced by 32% and 15%, respectively. The double-angle and outer-edge drill tip of the double-angle-tip drill resulted in less delamination and burr formation. SEM analysis further revealed that the double-angle-tip drill produced finer and smoother hole wall than the twist drill. These experimental findings provide valuable guidance for achieving low-damage drilling of thermoplastic composites.
- 4 August 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (39) , 40907-40919
Comparative Study on Mechanical Performance of Drilled Thermoplastic CF/PEEK Using Conventional Twist and Double-Angle Drills
- 4 August 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (39) , 40907-40919
Comparative Study on Mechanical Performance of Drilled Thermoplastic CF/PEEK Using Conventional Twist and Double-Angle Drills
- 29 June 2026
- Published by SAGE Publications in Journal of Composite Materials
Study on the single shear performance and failure mechanism of GFRP fasteners based on progressive damage model
Due to their lightweight and high-strength characteristics, composite fasteners have become one of the focal points in the field of composite material connections. This paper establishes progressive damage models for specimens with different connection methods. Through the implementation of the VUMAT subroutine based on the Hashin failure criteria, the single shear performance and damage processes of GFRP fasteners in bolt, screw, and stud connections are analyzed. The results indicate that bolts exhibit the highest single shear strength, followed by screws, with studs being the weakest, which is related to the structure of the specimens. The relative errors between the ultimate loads predicted by the finite element model and those obtained from experiments are 3.28%, 3.34%, and 5.49%, respectively. Bolts tend to approximate planar fracture characteristics, screw fracture surfaces show a pointed apex shape, while studs display stepped cracks. These findings align well with experimental results, verifying the reliability of the model.
- 29 June 2026
- Published by SAGE Publications in Journal of Composite Materials
Study on the single shear performance and failure mechanism of GFRP fasteners based on progressive damage model
Due to their lightweight and high-strength characteristics, composite fasteners have become one of the focal points in the field of composite material connections. This paper establishes progressive damage models for specimens with different connection methods. Through the implementation of the VUMAT subroutine based on the Hashin failure criteria, the single shear performance and damage processes of GFRP fasteners in bolt, screw, and stud connections are analyzed. The results indicate that bolts exhibit the highest single shear strength, followed by screws, with studs being the weakest, which is related to the structure of the specimens. The relative errors between the ultimate loads predicted by the finite element model and those obtained from experiments are 3.28%, 3.34%, and 5.49%, respectively. Bolts tend to approximate planar fracture characteristics, screw fracture surfaces show a pointed apex shape, while studs display stepped cracks. These findings align well with experimental results, verifying the reliability of the model.
- 24 February 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (S2)
Damage Reduction Mechanism in Drilling Carbon Fiber Reinforced Polyetheretherketone Composite With Double‐Angle Drill Based on Cutting‐Edge Decomposition
Drilling of carbon fiber reinforced polyetheretherketone (CF/PEEK) is prone to burr and delamination damage due to coupled thermal‐mechanical effects. A double‐angle drill featuring a double‐top angle and an outer‐edge tip is developed based on cutting‐edge decomposition to mitigate such damage. The drilling process of this drill is analyzed, and drilling experiments are conducted on CF/PEEK composites. Results demonstrated that the double‐angle drill demonstrated the best cutting performance. In comparison with the traditional twist drill, the double‐angle drill reduces the average thrust force and drilling temperature by 45.09% and 10.54%, respectively. This reduction is attributed to the shortened contact length between the cutting edge and chips, as well as the progressive cutting achieved by multiple cutting edges. Moreover, the double‐angle drill generated a lower delamination and burr factor, which can be attributed to its independent cutting tips. This design minimizes extrusion and thermal effects during the formation of the machined surface, thereby reducing hole‐making damage. This study presents a new methodology for improving the drilling quality of CF/PEEK composite.
- 24 February 2026
- Published by Wiley in Polymer Composites
- Vol. 47 (S2)
Damage Reduction Mechanism in Drilling Carbon Fiber Reinforced Polyetheretherketone Composite With Double‐Angle Drill Based on Cutting‐Edge Decomposition
Drilling of carbon fiber reinforced polyetheretherketone (CF/PEEK) is prone to burr and delamination damage due to coupled thermal‐mechanical effects. A double‐angle drill featuring a double‐top angle and an outer‐edge tip is developed based on cutting‐edge decomposition to mitigate such damage. The drilling process of this drill is analyzed, and drilling experiments are conducted on CF/PEEK composites. Results demonstrated that the double‐angle drill demonstrated the best cutting performance. In comparison with the traditional twist drill, the double‐angle drill reduces the average thrust force and drilling temperature by 45.09% and 10.54%, respectively. This reduction is attributed to the shortened contact length between the cutting edge and chips, as well as the progressive cutting achieved by multiple cutting edges. Moreover, the double‐angle drill generated a lower delamination and burr factor, which can be attributed to its independent cutting tips. This design minimizes extrusion and thermal effects during the formation of the machined surface, thereby reducing hole‐making damage. This study presents a new methodology for improving the drilling quality of CF/PEEK composite.
- 18 November 2025
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 39 (6) , 2951-2976
Comparative study of tool wear and machining quality in drilling of thermoplastic CF/PEEK and thermoset CF/epoxy composites
Carbon fiber reinforced polyetheretherketone (CF/PEEK) is widely used in the aviation industry due to its high performance and ease of recycling and repair. The PEEK matrix is easy to soften when heated, which causes serious tool wear and affects machining quality and efficiency. However, tool wear mechanisms in drilling CF/PEEK composites are still unclear and there is a lack of research on the relationship between tool wear and drilling performance. This is the first study presents a comprehensive comparative analysis of tool wear mechanisms and their influence on drilling temperature, cutting forces, and hole-making quality between thermoplastic CF/PEEK and thermoset CF/epoxy composites. The results indicate that the primary wear mechanism for drilling thermoset CF/epoxy is abrasive wear, while adhesion wear dominates in thermoplastic CF/PEEK. The drilling thrust force and temperature in CF/PEEK exhibit significantly higher sensitivity to the progression of tool wear. As the number of drilled holes increases, the hole-making quality of CF/PEEK exhibits a more pronounced deterioration compared to that of CF/epoxy. This study provides valuable insights into the distinct wear mechanisms and performance differences between thermoplastic and thermoset composites during drilling processes.
- 18 November 2025
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 39 (6) , 2951-2976
Comparative study of tool wear and machining quality in drilling of thermoplastic CF/PEEK and thermoset CF/epoxy composites
Carbon fiber reinforced polyetheretherketone (CF/PEEK) is widely used in the aviation industry due to its high performance and ease of recycling and repair. The PEEK matrix is easy to soften when heated, which causes serious tool wear and affects machining quality and efficiency. However, tool wear mechanisms in drilling CF/PEEK composites are still unclear and there is a lack of research on the relationship between tool wear and drilling performance. This is the first study presents a comprehensive comparative analysis of tool wear mechanisms and their influence on drilling temperature, cutting forces, and hole-making quality between thermoplastic CF/PEEK and thermoset CF/epoxy composites. The results indicate that the primary wear mechanism for drilling thermoset CF/epoxy is abrasive wear, while adhesion wear dominates in thermoplastic CF/PEEK. The drilling thrust force and temperature in CF/PEEK exhibit significantly higher sensitivity to the progression of tool wear. As the number of drilled holes increases, the hole-making quality of CF/PEEK exhibits a more pronounced deterioration compared to that of CF/epoxy. This study provides valuable insights into the distinct wear mechanisms and performance differences between thermoplastic and thermoset composites during drilling processes.
- 27 February 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (13) , 12155-12173
New strategy based on crystallinity control in enhancing the flexural strength of drilled CF / PEEK composite laminate
For the first time, this paper proposes a new strategy based on crystallinity control in enhancing the flexural strength of drilled carbon fiber reinforced polyetheretherketone (CF/PEEK) composite laminate. The high‐positive correlation between the unique crystalline characteristic of the CF/PEEK composite and its flexural strength is introduced into the strategy, and the superposition of pre‐heat treatment, intermediate‐heat treatment, and post‐heat treatment is carried out to increase the crystallinity. The optimal heat treatment temperature of 320 °C is identified through in situ X‐ray Diffraction (XRD) patterns. The results show that the proposed strategy effectively increased the crystallinity by 21.70%, leading in turn to an increase the flexural strength of the CF/PEEK by 19.56%. The heat treatment compacts the molecular chains, enhancing the intermolecular interactions, which in turn result in increased thrust force in the drilled laminate. Four‐point flexural loading experiments of the open‐hole laminate reveal that CF/PEEK generates compression and tension failures at the macroscopic level and interlaminar and intralaminar failure at the microscopic level. Finally, the enhancement mechanism is elucidated, in which the transcrystallization of the matrix PEEK caused by heat treatment results in stronger bonding strength between the fiber and matrix, ultimately leading to an improved flexural strength of the drilled CF/PEEK laminate. Highlights: Novel strategy enhances CF/PEEK flexural strength via crystallinity control. 21.70% crystallinity increase boosts CF/PEEK flexural strength by 19.56%. Optimal heat treatment at 320 °C is identified for CF/PEEK composites. Flexural tests reveal compression, tension, and interlaminar failures in CF/PEEK. Heat treatment fosters crystallization, improving CF/PEEK flexural strength.
- 27 February 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (13) , 12155-12173
New strategy based on crystallinity control in enhancing the flexural strength of drilled CF / PEEK composite laminate
For the first time, this paper proposes a new strategy based on crystallinity control in enhancing the flexural strength of drilled carbon fiber reinforced polyetheretherketone (CF/PEEK) composite laminate. The high‐positive correlation between the unique crystalline characteristic of the CF/PEEK composite and its flexural strength is introduced into the strategy, and the superposition of pre‐heat treatment, intermediate‐heat treatment, and post‐heat treatment is carried out to increase the crystallinity. The optimal heat treatment temperature of 320 °C is identified through in situ X‐ray Diffraction (XRD) patterns. The results show that the proposed strategy effectively increased the crystallinity by 21.70%, leading in turn to an increase the flexural strength of the CF/PEEK by 19.56%. The heat treatment compacts the molecular chains, enhancing the intermolecular interactions, which in turn result in increased thrust force in the drilled laminate. Four‐point flexural loading experiments of the open‐hole laminate reveal that CF/PEEK generates compression and tension failures at the macroscopic level and interlaminar and intralaminar failure at the microscopic level. Finally, the enhancement mechanism is elucidated, in which the transcrystallization of the matrix PEEK caused by heat treatment results in stronger bonding strength between the fiber and matrix, ultimately leading to an improved flexural strength of the drilled CF/PEEK laminate. Highlights: Novel strategy enhances CF/PEEK flexural strength via crystallinity control. 21.70% crystallinity increase boosts CF/PEEK flexural strength by 19.56%. Optimal heat treatment at 320 °C is identified for CF/PEEK composites. Flexural tests reveal compression, tension, and interlaminar failures in CF/PEEK. Heat treatment fosters crystallization, improving CF/PEEK flexural strength.
- 24 April 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58 (16) , 1815-1828
Study of the tensile mechanical properties and failure mechanisms of CFRP screwed joints
Removable joint technology is commonly used in composite laminates for various load-bearing structures. However, existing research primarily focuses on bolted joints, there is relatively limited research on screwed joints in composite materials. This study investigates the influence of connected layer thickness and hole diameter on the tensile behavior of threaded joints in carbon fiber-reinforced polymer (CFRP) laminates. After fabricating different CFRP screwed joint specimens, tensile tests were conducted. The digital image correlation (DIC) technique captured the deformation process. The experiment results indicate a significant increase in load-bearing capacity with the increase in diameter. For instance, joints with an 8 mm diameter exhibited a load-bearing capacity of 10.82 kN. The increase in the connected layer thickness correspondingly enhanced the load-bearing capacity of the joint. The joint with a thickness of 7 mm had the highest load-bearing capacity of 8.83 kN. Besides, with the increase in the thickness of the connected layer, the failure mode transitioned from shear failure in the connected layer to screw pull-out. The tilt angle of the screw during the pull-out process also decreases with the increase in the connected layer thickness. Strain and out-of-plane displacement measurements under ultimate load conditions verify these observations.
- 24 April 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58 (16) , 1815-1828
Study of the tensile mechanical properties and failure mechanisms of CFRP screwed joints
Removable joint technology is commonly used in composite laminates for various load-bearing structures. However, existing research primarily focuses on bolted joints, there is relatively limited research on screwed joints in composite materials. This study investigates the influence of connected layer thickness and hole diameter on the tensile behavior of threaded joints in carbon fiber-reinforced polymer (CFRP) laminates. After fabricating different CFRP screwed joint specimens, tensile tests were conducted. The digital image correlation (DIC) technique captured the deformation process. The experiment results indicate a significant increase in load-bearing capacity with the increase in diameter. For instance, joints with an 8 mm diameter exhibited a load-bearing capacity of 10.82 kN. The increase in the connected layer thickness correspondingly enhanced the load-bearing capacity of the joint. The joint with a thickness of 7 mm had the highest load-bearing capacity of 8.83 kN. Besides, with the increase in the thickness of the connected layer, the failure mode transitioned from shear failure in the connected layer to screw pull-out. The tilt angle of the screw during the pull-out process also decreases with the increase in the connected layer thickness. Strain and out-of-plane displacement measurements under ultimate load conditions verify these observations.
- 10 April 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (10) , 9376-9388
Experimental investigation on effect of tool geometry on thermal and crystallization characteristics in drilling of carbon fiber reinforced PEEK composite
This paper comprehensively investigated the effect of the tool geometries on heat transfer and special crystallization characteristics in the drilling of carbon fiber‐reinforced polyetheretherketone (CF/PEEK) composite for the first time. Three tools with different geometries (twist, brad, and dagger drill) are carried out on CF/PEEK drilling experiments, and temperature, as well as crystallinity and surface roughness, are introduced to make a comparative evaluation on the effect of the tool geometries. The results show that the drilling temperature is determined by the contact length of the profile between the drill and the material. Correspondingly, better surface quality with lower surface roughness and smoother surface is obtained by using a twist drill due to the heat‐induced PEEK smearing effect. Further, in situ XRD and differential scanning calorimeter (DSC) were used to characterize the crystallization characteristics where crystal phase transformation at different temperatures was measured. The occurring temperature of the strongest crystallization characteristics for CF/PEEK is basically not affected by tool geometries, all at 300°C, and the limiting crystallization temperature is 344.5 ± 0.7°C. The crystallinity is found to be affected by drilling temperature and cooling rate and gradually decreases along the heat transfer direction. This work provides a new sight into the improvement of CF/PEEK drilling.Highlights: The effect of tool geometries on thermal and crystallization for CF/PEEK is provided. In situ XRD and DSC are used to characterize crystallization characteristics. The drilling temperature and cooling rate are both determinants of crystallinity. The limiting crystallization temperature of the CF/PEEK composite is 344.5 ± 0.7°C. Heat‐induced PEEK smearing effect improves the surface quality of CF/PEEK drilling.
- 10 April 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (10) , 9376-9388
Experimental investigation on effect of tool geometry on thermal and crystallization characteristics in drilling of carbon fiber reinforced PEEK composite
This paper comprehensively investigated the effect of the tool geometries on heat transfer and special crystallization characteristics in the drilling of carbon fiber‐reinforced polyetheretherketone (CF/PEEK) composite for the first time. Three tools with different geometries (twist, brad, and dagger drill) are carried out on CF/PEEK drilling experiments, and temperature, as well as crystallinity and surface roughness, are introduced to make a comparative evaluation on the effect of the tool geometries. The results show that the drilling temperature is determined by the contact length of the profile between the drill and the material. Correspondingly, better surface quality with lower surface roughness and smoother surface is obtained by using a twist drill due to the heat‐induced PEEK smearing effect. Further, in situ XRD and differential scanning calorimeter (DSC) were used to characterize the crystallization characteristics where crystal phase transformation at different temperatures was measured. The occurring temperature of the strongest crystallization characteristics for CF/PEEK is basically not affected by tool geometries, all at 300°C, and the limiting crystallization temperature is 344.5 ± 0.7°C. The crystallinity is found to be affected by drilling temperature and cooling rate and gradually decreases along the heat transfer direction. This work provides a new sight into the improvement of CF/PEEK drilling.Highlights: The effect of tool geometries on thermal and crystallization for CF/PEEK is provided. In situ XRD and DSC are used to characterize crystallization characteristics. The drilling temperature and cooling rate are both determinants of crystallinity. The limiting crystallization temperature of the CF/PEEK composite is 344.5 ± 0.7°C. Heat‐induced PEEK smearing effect improves the surface quality of CF/PEEK drilling.
- 19 December 2023
- Published by Elsevier in Composites Part B: Engineering
- Vol. 271
Tensile mechanical properties and damage analysis of layered woven GFRP composite bolts
- 19 December 2023
- Published by Elsevier in Composites Part B: Engineering
- Vol. 271
Tensile mechanical properties and damage analysis of layered woven GFRP composite bolts