Shangzhe Yu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shangzhe Yu has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Felix Kunz
Institute of Energy and Climate Research, Fundamental Electrochemistry (IEK-9), Forschungszentrum Jülich GmbH, D-52425 Jülich, Germany
5 shared publications - Rüdiger-Albert Eichel
Forschungszentrum Jülich
5 shared publications - Dominik Schäfer
Forschungszentrum Jülich, IET-1: Fundamental Electrochemistry
4 shared publications - Roland Peters
Institute of Energy and Climate Research, Fundamental Electrochemistry (IEK-9), Forschungszentrum Jülich GmbH, D-52425 Jülich, Germany
4 shared publications - Shidong Zhang
Institute of Energy and Climate Research, Fundamental Electrochemistry (IEK-9), Forschungszentrum Jülich GmbH, D-52425 Jülich, Germany
4 shared publications Holger Marschall
1 shared publication
Latest Publications
- Open Access
A Three-Dimensional Time-Dependent Model of the Degradation Caused by Chromium Poisoning in a Solid Oxide Fuel Cell Stack
Chromium poisoning strongly influences the performance of solid oxide fuel cell (SOFC) stacks. A novel numerical model is introduced by incorporating the chemical and electrochemical aspects of chromium poisoning. It offers a detailed analysis of the spatial distribution of critical chromium-based species, including SrCrO4 and Cr2O3. This model is integrated with a pre-existing three-dimensional, time-dependent computational fluid dynamics (CFD) toolbox, openFuelCell2. The numerical simulations indicate a quantitative agreement with experimental data over an extended 100 kh operation. Numerical simulations are conducted within a representative channel geometry originating from an F10 SOFC stack at Forschungszentrum Jülich GmbH, and consider a wide range of stack designs, temperatures, and air absolute humidities. The simulation results demonstrate the potential of a protective coating produced through atmospheric plasma spraying (APS) technology in nearly eliminating chromium poisoning. It is also found that the APS protective coating could enable the operation of an SOFC stack with low requirements of air dehumidification at a temperature of 650 C.Open AccessA Three-Dimensional Time-Dependent Model of the Degradation Caused by Chromium Poisoning in a Solid Oxide Fuel Cell Stack
Chromium poisoning strongly influences the performance of solid oxide fuel cell (SOFC) stacks. A novel numerical model is introduced by incorporating the chemical and electrochemical aspects of chromium poisoning. It offers a detailed analysis of the spatial distribution of critical chromium-based species, including SrCrO4 and Cr2O3. This model is integrated with a pre-existing three-dimensional, time-dependent computational fluid dynamics (CFD) toolbox, openFuelCell2. The numerical simulations indicate a quantitative agreement with experimental data over an extended 100 kh operation. Numerical simulations are conducted within a representative channel geometry originating from an F10 SOFC stack at Forschungszentrum Jülich GmbH, and consider a wide range of stack designs, temperatures, and air absolute humidities. The simulation results demonstrate the potential of a protective coating produced through atmospheric plasma spraying (APS) technology in nearly eliminating chromium poisoning. It is also found that the APS protective coating could enable the operation of an SOFC stack with low requirements of air dehumidification at a temperature of 650 C. - Open Access
- 25 October 2023
- Published by MDPI AG in Preprints.org
A Three-Dimensional Time-Dependent Model of the Degradation Caused by Chromium Poisoning in a Solid Oxide Fuel Cell Stack
Chromium poisoning strongly influences the performance of solid oxide fuel cell (SOFC) stacks. A three-dimensional, time-dependent, computational fluid dynamics model of a single channel of a F10 SOFC stack in Forschungszentrum Jülich GmbH is developed to investigate chromium poisoning for different stack designs, temperatures and absolute air humidities. The model takes into account both chemical and electrochemical mechanisms of chromium poisoning and is able to predict the spatial distribution of SrCrO4 and Cr2O3. The voltage degradation over 100 kh can be simulated quantitatively. According to the simulation results, chromium poisoning is almost eliminated by the application of the protective coating fabricated by the atmospheric plasma-spraying (APS) technology. Besides, with the help of the APS protective coating, operating a SOFC stack with less dehumidified air at 650 oC is possible according to the simulation.
- 25 October 2023
- Published by MDPI AG in Preprints.org
Open AccessA Three-Dimensional Time-Dependent Model of the Degradation Caused by Chromium Poisoning in a Solid Oxide Fuel Cell Stack
Chromium poisoning strongly influences the performance of solid oxide fuel cell (SOFC) stacks. A three-dimensional, time-dependent, computational fluid dynamics model of a single channel of a F10 SOFC stack in Forschungszentrum Jülich GmbH is developed to investigate chromium poisoning for different stack designs, temperatures and absolute air humidities. The model takes into account both chemical and electrochemical mechanisms of chromium poisoning and is able to predict the spatial distribution of SrCrO4 and Cr2O3. The voltage degradation over 100 kh can be simulated quantitatively. According to the simulation results, chromium poisoning is almost eliminated by the application of the protective coating fabricated by the atmospheric plasma-spraying (APS) technology. Besides, with the help of the APS protective coating, operating a SOFC stack with less dehumidified air at 650 oC is possible according to the simulation.
- Open Access
- 5 October 2023
- Published by Elsevier in Electrochimica Acta
- Vol. 472
A new procedure for rapid convergence in numerical performance calculations of electrochemical cells
- 5 October 2023
- Published by Elsevier in Electrochimica Acta
- Vol. 472
Open AccessA new procedure for rapid convergence in numerical performance calculations of electrochemical cells
- Open Access
Numerical Modeling and Simulation of the Solid Oxide Cell Stacks and Metal Interconnect Oxidation with OpenFOAM
Solid oxide cells are capable of efficiently converting various chemical energy carriers to electricity and vice versa. The urgent challenge nowadays is the faster degradation rate compared with other fuel cell/electrolyzer technologies. To understand the degradation mechanisms, simulation of a solid oxide cell is helpful. Since most previous research developed models using commercial software, such as COMSOL and ANSYS Fluent, a gap for knowledge transfer is being gradually formed between academia and industry due to licensing issues. This paper introduces a multiphysics model, developed by a computational code, openFuelCell2. The code is implemented with an open-source library, OpenFOAM. It accounts for momentum transfer, mass transfer, electrochemical reactions and metal interconnect oxidation. The model can precisely predict I–V curves under different temperatures, fuel humidity and operation modes. Comparison between OpenFOAM and COMSOL simulations shows good agreement. The metal interconnect oxidation is modeled, which can predict the thickness of the oxide scale under different protective coatings. Simulations are conducted by assuming an ultra-thin film resistance on the rib surface. It is revealed that coatings fabricated by atmospheric plasma spraying can efficiently prevent metal interconnect oxidation, with a contribution of only 0.53 % to the total degradation rate.
Open AccessNumerical Modeling and Simulation of the Solid Oxide Cell Stacks and Metal Interconnect Oxidation with OpenFOAM
Solid oxide cells are capable of efficiently converting various chemical energy carriers to electricity and vice versa. The urgent challenge nowadays is the faster degradation rate compared with other fuel cell/electrolyzer technologies. To understand the degradation mechanisms, simulation of a solid oxide cell is helpful. Since most previous research developed models using commercial software, such as COMSOL and ANSYS Fluent, a gap for knowledge transfer is being gradually formed between academia and industry due to licensing issues. This paper introduces a multiphysics model, developed by a computational code, openFuelCell2. The code is implemented with an open-source library, OpenFOAM. It accounts for momentum transfer, mass transfer, electrochemical reactions and metal interconnect oxidation. The model can precisely predict I–V curves under different temperatures, fuel humidity and operation modes. Comparison between OpenFOAM and COMSOL simulations shows good agreement. The metal interconnect oxidation is modeled, which can predict the thickness of the oxide scale under different protective coatings. Simulations are conducted by assuming an ultra-thin film resistance on the rib surface. It is revealed that coatings fabricated by atmospheric plasma spraying can efficiently prevent metal interconnect oxidation, with a contribution of only 0.53 % to the total degradation rate.
- Open Access
- 10 April 2023
- Published by MDPI AG in Preprints.org
Numerical Modelling and Simulation of the Solid Oxide Cell Stacks and Metal Interconnect Oxidation With OpenFOAM
Solid oxide cells are capable of efficiently converting various chemical energy carriers to electricity and vice versa. The urgent challenge nowadays is the faster degradation rate compared with other fuel cell/electrolyzer technologies. To understand the degradation mechanisms, simulation of a solid oxide cell is helpful. Since most previous research developed models using commercial software, such as COMSOL and ANSYS Fluent, a gap for knowledge transfer is being gradually formed between academia and industry due to licensing issues. This paper introduces a multiphysics model, developed by a computational code, openFuelCell2. The code is implemented with an open-source library, OpenFOAM. It accounts for momentum transfer, mass transfer, electrochemical reactions and metal interconnect oxidation. The model can precisely predict I-V curves under different temperatures, fuel humidity and operation modes. Comparison between OpenFOAM and COMSOL simulations shows good agreement. The metal interconnect oxidation is modelled, which can predict the thickness of the oxide scale under different protective coatings. Simulations are conducted by assuming an ultra-thin film resistance on the rib surface. It is revealed that coatings fabricated by atmospheric plasma spraying can efficiently prevent metal interconnect oxidation, with a contribution of only 0.53 \% to the total degradation rate.
- 10 April 2023
- Published by MDPI AG in Preprints.org
Open AccessNumerical Modelling and Simulation of the Solid Oxide Cell Stacks and Metal Interconnect Oxidation With OpenFOAM
Solid oxide cells are capable of efficiently converting various chemical energy carriers to electricity and vice versa. The urgent challenge nowadays is the faster degradation rate compared with other fuel cell/electrolyzer technologies. To understand the degradation mechanisms, simulation of a solid oxide cell is helpful. Since most previous research developed models using commercial software, such as COMSOL and ANSYS Fluent, a gap for knowledge transfer is being gradually formed between academia and industry due to licensing issues. This paper introduces a multiphysics model, developed by a computational code, openFuelCell2. The code is implemented with an open-source library, OpenFOAM. It accounts for momentum transfer, mass transfer, electrochemical reactions and metal interconnect oxidation. The model can precisely predict I-V curves under different temperatures, fuel humidity and operation modes. Comparison between OpenFOAM and COMSOL simulations shows good agreement. The metal interconnect oxidation is modelled, which can predict the thickness of the oxide scale under different protective coatings. Simulations are conducted by assuming an ultra-thin film resistance on the rib surface. It is revealed that coatings fabricated by atmospheric plasma spraying can efficiently prevent metal interconnect oxidation, with a contribution of only 0.53 \% to the total degradation rate.