Ali Akay
Research Subjects
Ali Akay has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Aydın Şık
Gazi Üniversitesi
2 shared publications - Fatih Güven
Department of Mechanical Engineering, Faculty of Mechanical Engineering, Yildiz Technical University, Istanbul 34349, Türkiye
1 shared publication - Turabi Bi̇ngöl
Birikim Mühendislik Tasarım Merkezi
1 shared publication
Latest Publications
- Open Access
- 24 September 2026
- Published by SAGE Publications in Science and Technology of Welding and Joining
Mechanical and microstructural characterization of dissimilar welded joints between S355J2 + N and S690QL steels using G69 and T46 filler wires
This study evaluates and compares the mechanical performance and microstructures of dissimilar welded joints made from S355J2 + N and S690QL steels, using G69 and T46 fillers. Tensile, Charpy V-notch (CVN) impact, and hardness tests were conducted, along with optical microscopy and scanning electron microscopy (SEM) for microstructural and fractographic analysis. Average ultimate tensile strengths reached 540 ± 2.5 MPa for T46 and 524 ± 2.5 MPa for G69 joints, with all specimens fracturing within the weaker base metal (S355J2 + N) that had an ultimate tensile strength of 479 MPa, indicating successful overmatching with joint integrity. Hardness examination showed a peak value of 282 ± 3 HV in the S690QL-HAZ, attributed to the formation of martensite laths and localized tempered martensite. The G69 filler wire exhibited higher energy absorption ( 94 ± 13 J at − 20 ∘ C ) compared to the T46 wire ( 67 ± 23 J ). The T46 weld zone showed a higher density of brittle cleavage facets, likely due to the presence of M-A constituents. Despite the variances, all tested specimens fulfilled the minimum impact toughness requirement of 27 J at − 20 ∘ C according to EN 10025-2 standard for S355J2 + N structural steel, demonstrating that both filler wires are appropriate for high-strength dissimilar steel applications under the investigated conditions.
- 24 September 2026
- Published by SAGE Publications in Science and Technology of Welding and Joining
Open AccessMechanical and microstructural characterization of dissimilar welded joints between S355J2 + N and S690QL steels using G69 and T46 filler wires
This study evaluates and compares the mechanical performance and microstructures of dissimilar welded joints made from S355J2 + N and S690QL steels, using G69 and T46 fillers. Tensile, Charpy V-notch (CVN) impact, and hardness tests were conducted, along with optical microscopy and scanning electron microscopy (SEM) for microstructural and fractographic analysis. Average ultimate tensile strengths reached 540 ± 2.5 MPa for T46 and 524 ± 2.5 MPa for G69 joints, with all specimens fracturing within the weaker base metal (S355J2 + N) that had an ultimate tensile strength of 479 MPa, indicating successful overmatching with joint integrity. Hardness examination showed a peak value of 282 ± 3 HV in the S690QL-HAZ, attributed to the formation of martensite laths and localized tempered martensite. The G69 filler wire exhibited higher energy absorption ( 94 ± 13 J at − 20 ∘ C ) compared to the T46 wire ( 67 ± 23 J ). The T46 weld zone showed a higher density of brittle cleavage facets, likely due to the presence of M-A constituents. Despite the variances, all tested specimens fulfilled the minimum impact toughness requirement of 27 J at − 20 ∘ C according to EN 10025-2 standard for S355J2 + N structural steel, demonstrating that both filler wires are appropriate for high-strength dissimilar steel applications under the investigated conditions.
- Open Access
- 1 June 2025
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 38 (2) , 847-863
Vertical Stirred Mill (VSM) Welding Machine Design
Vertical stirred mills are widely used in the mining industry because they are more efficient than traditional drum mills. Vertical agitation grinders are used in secondary, regrinding, and fine grinding applications in the mining industry because of their energy efficiency, cost savings and small footprint. The solid welding of the mixer leaves to the body plays an important role in terms of wear, maintenance planning, and operating costs. The grinder must be resistant to the strains during mixing and maintain its rigidity. In vertical mixer grinders, it is difficult to weld the screw leaves to the shaft in a helical manner. In this study, a Screw Welding Machine (WSM) was designed to weld the vertical stirred grinder leaves to the body to meet this difficulty. In order to perform welds between adjacent leaves and corners, using a submerged arc welding machine, a welding bench has been designed. Designed bench enable to connect seven different sizes of vertical mixer grinders to WSM. Designed WSM compansate deformations caused bey weld induced heat by changing part position and opposite side weld application. The designed bench remains stationary during welding procedure. The weld seam qualities were investigated by examining the weld seams made with the designed machine (spectral analysis, hardness measurement, notch impact resistance, macro examination, and metallography examination).
- 1 June 2025
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 38 (2) , 847-863
Open AccessVertical Stirred Mill (VSM) Welding Machine Design
Vertical stirred mills are widely used in the mining industry because they are more efficient than traditional drum mills. Vertical agitation grinders are used in secondary, regrinding, and fine grinding applications in the mining industry because of their energy efficiency, cost savings and small footprint. The solid welding of the mixer leaves to the body plays an important role in terms of wear, maintenance planning, and operating costs. The grinder must be resistant to the strains during mixing and maintain its rigidity. In vertical mixer grinders, it is difficult to weld the screw leaves to the shaft in a helical manner. In this study, a Screw Welding Machine (WSM) was designed to weld the vertical stirred grinder leaves to the body to meet this difficulty. In order to perform welds between adjacent leaves and corners, using a submerged arc welding machine, a welding bench has been designed. Designed bench enable to connect seven different sizes of vertical mixer grinders to WSM. Designed WSM compansate deformations caused bey weld induced heat by changing part position and opposite side weld application. The designed bench remains stationary during welding procedure. The weld seam qualities were investigated by examining the weld seams made with the designed machine (spectral analysis, hardness measurement, notch impact resistance, macro examination, and metallography examination).
- 29 April 2023
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 31 (1) , 558-571
THE OPTIMIZATION OF WELDING WIDTH BY TAGUCHI TECHNIQUE IN SUBMERGED ARC WELDING (SAW) METHOD
Dikey karıştırıcılı öğütücüler, çeşitli maden cevherinin ekonomik olarak öğütülmesinde kullanılırlar. Karıştırma vidası öğütme haznesinin üstüne dik eksenli çalışacak şekilde yataklanması yapılır. Öğütücü karıştırma sırasında oluşan zorlanmalara karşı mukavim olması ve rijitliğini koruması istenir. Bu nedenle parçalar birleştirilirken en iyi kaynak yöntemi seçilmelidir. Kaynaklı birleştirmelerde tüm kaynak işlemleri, istenen kaynak dikişi parametreleri, minimum bozulma ile mükemmel mekanik özellikler ile kaynaklı bir bağlantı elde etmek amacıyla kullanılır. Tozaltı Ark Kaynağı (SAW) işlemi, kolay uygulanabilirliği, yüksek akım yoğunluğu ve aynı anda birden fazla tel kullanarak büyük miktarda kaynak metali biriktirme kabiliyeti nedeniyle geniş endüstriyel uygulama alanı bulmaktadır. Özellikle aşınmış parçaları onarabilme özelliğinden dolayı imalatta çokça uygulanmaktadır. Kaliteli bir bağlantı elde etmek için, SAW’ın çeşitli proses parametrelerinin incelenmesi ve kaynak kalitesini iyileştirmek için hassas bir şekilde seçilmesi gerekir. SAW, daha sonra kaynak kalitesini etkileyen biriktirme hızı, seyreltme ve sertlik gibi performans çıktılarını etkileyen çok sayıda proses parametresi ile karakterize edilir. . Bu nedenle vida yapraklarının mile kaynağı SAW yöntemi ile yapılmıştır. SAW makinesi ile kaynak yapılmış deney numuneleri Taguchi'nin deney tasarımına göre veriler toplanmış ve sürecin girdi-çıktı ilişkilerini kurmak için varyans (ANOVA) ve regrasyon analizi yapılmıştır. Optimum kaynak parametrelerini belirlemek için ANN modellerine dayalı optimizasyon prosedürlerini kullanan iyi bir dikiş geometrisi elde edilmesi amaçlanmıştır. Bu tekniklerden elde edilen optimize edilmiş değerler deneysel sonuçlarla karşılaştırılmış ve sunulmuştur.
- 29 April 2023
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 31 (1) , 558-571
THE OPTIMIZATION OF WELDING WIDTH BY TAGUCHI TECHNIQUE IN SUBMERGED ARC WELDING (SAW) METHOD
Dikey karıştırıcılı öğütücüler, çeşitli maden cevherinin ekonomik olarak öğütülmesinde kullanılırlar. Karıştırma vidası öğütme haznesinin üstüne dik eksenli çalışacak şekilde yataklanması yapılır. Öğütücü karıştırma sırasında oluşan zorlanmalara karşı mukavim olması ve rijitliğini koruması istenir. Bu nedenle parçalar birleştirilirken en iyi kaynak yöntemi seçilmelidir. Kaynaklı birleştirmelerde tüm kaynak işlemleri, istenen kaynak dikişi parametreleri, minimum bozulma ile mükemmel mekanik özellikler ile kaynaklı bir bağlantı elde etmek amacıyla kullanılır. Tozaltı Ark Kaynağı (SAW) işlemi, kolay uygulanabilirliği, yüksek akım yoğunluğu ve aynı anda birden fazla tel kullanarak büyük miktarda kaynak metali biriktirme kabiliyeti nedeniyle geniş endüstriyel uygulama alanı bulmaktadır. Özellikle aşınmış parçaları onarabilme özelliğinden dolayı imalatta çokça uygulanmaktadır. Kaliteli bir bağlantı elde etmek için, SAW’ın çeşitli proses parametrelerinin incelenmesi ve kaynak kalitesini iyileştirmek için hassas bir şekilde seçilmesi gerekir. SAW, daha sonra kaynak kalitesini etkileyen biriktirme hızı, seyreltme ve sertlik gibi performans çıktılarını etkileyen çok sayıda proses parametresi ile karakterize edilir. . Bu nedenle vida yapraklarının mile kaynağı SAW yöntemi ile yapılmıştır. SAW makinesi ile kaynak yapılmış deney numuneleri Taguchi'nin deney tasarımına göre veriler toplanmış ve sürecin girdi-çıktı ilişkilerini kurmak için varyans (ANOVA) ve regrasyon analizi yapılmıştır. Optimum kaynak parametrelerini belirlemek için ANN modellerine dayalı optimizasyon prosedürlerini kullanan iyi bir dikiş geometrisi elde edilmesi amaçlanmıştır. Bu tekniklerden elde edilen optimize edilmiş değerler deneysel sonuçlarla karşılaştırılmış ve sunulmuştur.