DSDa Eun Shim

Da Eun Shim

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Da Eun Shim has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Comprehensive Device to System Co-Design for SOT-MRAM at the 7 nm Node

    by Piyush Kumar, Da Eun Shim, Azad Naeemi

    This work presents a comprehensive spin-orbit torque (SOT) based random access memory (MRAM) design at the 7nm technology node, spanning from device-level characteristics to system-level power performance area (PPA). At the device-level, we show the trade-offs among the write current, error rate, and time, based on mircomagnetic simulations. Based on ASAP7 PDK design rules, we create the bit-cell and peripheral layouts for SOT-MRAM and design the entire array. In addition, we quantify various array-level trade-offs using full array SPICE circuit simulations based on layout-extracted parasitic netlists. This is then used to design the entire SOT-MRAM system along with a memory controller. Based on place and route, we evaluate the system-level PPA for various memory capacities, demonstrating bit-densities up to 14.8 Mb/mm2 and read bandwidths up to 2.98 GB/s. Our results show that increasing the memory size from 1 Mb to 16 Mb results in a performance degradation of ∼33-38% due to the impact of interconnect delay. As the results show that the performance of SOT-MRAM is limited by the interconnect delay, it is critical to co-optimize the device and interconnect technology to make SOT-MRAM a viable option at the advanced technology nodes. In addition, material discovery for field-free perpendicular magnetization switching in SOT devices based on out-of-plane spin torque is necessary to achieve SRAM level write energies.


  • GT3: An Open-Source 3-nm GAAFET PDK and Platform for End-to-End Evaluation of Emerging Technologies

    by Da Eun Shim, Piyush Kumar, Akshata Ashok Kini, Meghana Mallikarjuna, Nahid Haque Shazon, Azad Naeemi

    In this article, we present a comprehensive end-to-end evaluation platform for various front-end-of-line (FEOL) and back-end-of-line (BEOL) technology options at the 3-nm technology node. Based on TCAD modeling of FE and BE, we have developed a 3-nm GAAFET-based process design kit (PDK). We have developed a 6-track standard cell library including 65 cells with a library height of 144 nm. Based on TCAD modeling of interconnects, we have evaluated the resistance of the entire BEOL stack using ruthenium for lower metal levels (M0–M3) and copper for higher metal levels (M4–M13). Based on place and route (PnR) studies using our PDK, we have analyzed the impact of high aspect ratio (AR) Ru interconnects at M2 and M3 in terms of performance using benchmark designs. Our results show that using Ru interconnects improves the circuit performance by up to 10.4% compared with Cu interconnects and that increasing the AR generally results in performance degradation due to the increase in capacitance and via resistances. We have observed a 5.9% and 4% degradation in performance for AES and LDPC, respectively, when moving from AR2 to AR6 local interconnects. However, adding an airgap can improve the higher AR Ru interconnect cases and AR4 with airgap case shows the most performance improvement with an overall 19.7% improvement compared with Cu. This case study also serves as an example that shows the importance of an end-to-end evaluation platform.


  • Open Access

    GNN-based Multi-bit Flip-flop Clustering and Post-clustering Design Optimization for Energy-efficient 3D ICs

    by Pruek Vanna-Iampikul, Yi-Chen Lu, Da Eun Shim, Sung Kyu Lim

    In high-performance three-dimensional Integrated Circuits (3D ICs), clock networks consume a large portion of the full-chip power. However, no previous 3D IC work has ever optimized 3D clock networks for both power and performance simultaneously, which results in sub-optimal 3D designs. To overcome this issue, in this article, we propose a GNN-based flip-flop clustering algorithm that merges single-bit flip-flops into multi-bit flip-flops in an unsupervised manner, which jointly optimizes the power and performance metrics of clock networks. Moreover, we integrate our algorithm into the state-of-the-art 3D physical design flow and verify the integration, which leads to a better 3D full-chip design. Experimental results on eight industrial benchmarks demonstrate that the algorithm achieves improvements up to 18% in total power and 8.2% in performance over the state-of-the-art 3D flow.


  • A Comprehensive Modeling Platform for Interconnect Technologies

    by Da Eun Shim, Victor Huang, Xinkang Chen, Sumeet K. Gupta, Azad Naeemi

    With device scaling facing major physical and manufacturing challenges, many research efforts have been focused on the impact of device parameters and designs on circuit performance and power dissipation. However, similar research on the impact of Cu-low ${k}$ interconnects at the advanced nodes and the potential benefits offered by novel wire and via material and process options is lacking. While studies based on smaller circuit blocks exist, the exploration of these benefits for the performance of larger processors is lacking although the limits imposed by interconnect resistances become more severe due to longer wires and increased complexity in larger circuits. In this article, we conduct a study to quantify the effect of back-end-of-the-line (BEOL) technology improvements on circuit power, performance, and area (PPA) of various circuits from small blocks up to a full commercial processor with L1-cache. We modified the interconnect technology (ICT) files for the ASAP7 process design kit (PDK) to reflect various BEOL options such as thinner barrier/liners, near barrierless vias, and alternative material options based on TCAD simulations. We show that these options can offer up to a $1.769\times $ improvement in effective frequency or up to three metal-level savings.