Jinduo Li

The duration of water immersion significantly affects the mechanical response of rock materials. This study investigated the weakly cemented sandstone from the Wulagen Open-pit Mine to examine how varying immersion times affected the mineral composition, micro-porous structure, and macro-mechanical properties of the sandstone. The current study aimed to explore the mechanisms underlying the degradation of the strength and deformability of sandstone due to prolonged water exposure. The analysis showed that immersion time notably influenced the pore structure as well as the mineralogical characteristics of weakly cemented sandstone. These changes were the primary factors leading to alterations in its mechanical properties and failure modes. Specifically, with increasing immersion time, clay minerals absorbed water and expanded, with the most significant expansion occurring between 30 and 60 days. This rapid internal crack growth led to an exponential decrease in compressive strength and elastic modulus, with the most significant decline occurring between 30 and 60 days. The failure mode of the sandstone transitioned from extensional fracture to shear failure. Acoustic emission analysis revealed that, in the dry state, tensile cracks were about three times more prevalent than shear cracks, while after 60 days of immersion, shear cracks accounted for over 80%. After 60 days of immersion, microscopic cracks were fully interconnected, and the mechanical properties of the sandstone showed minimal change, with shear failure becoming predominant. These experimental results provide theoretical guidance for preventing the collapse of slopes composed of weakly cemented rock under long-term immersion conditions.

Metallic ore deposits are generally formed through magmatic intrusions, followed by metamorphism. The geological structures in such regions are often complex, with mechanical parameters exhibiting significant variability. These characteristics dictate the need for refined geological modeling and heterogeneous mechanical parameters for rock mass stability analysis to ensure reliability. Therefore, this paper proposes a novel method for rock mass stability analysis. The method fully leverages high-density drilling data from the mine and introduces an intelligent rock quality designation (RQD) identification technique, facilitating characterization of the spatial heterogeneity of rock mass RQD. Building on this, laboratory experiment data and in situ measurements are integrated, and the Hoek–Brown criterion is employed to achieve a refined characterization of heterogeneous rock mass mechanical parameters. This method allows for a realistic inversion of in situ rock mass mechanical conditions, overcoming the limitations inherent in assigning uniform parameters. Finally, the computed rock mass mechanical parameters are assigned to the refined computational model to conduct rock mass stability analysis. Taking the Jiangfeng Iron Mine, with its complex geological conditions, as an example, this method enables the accurate evaluation of the rock mass stability, determines the feasibility of joint mining, and calculates the appropriate thickness of the isolation pillars, effectively mitigating safety risks in mining operations. This method provides a valuable reference for the rock mass stability analysis of underground joint mining operations for similar mines.

1. China has 262 resource-based cities (State Council of the PRC 2013), which have made historic contributions to China’s economic development. However, after long-term and large-scale resource exp...

Bedding-controlled landslides are a common geological hazard for open-pit metal mines and occur on layered rock slopes. It can spread spatially over the final boundary of the dip slope and persist throughout the entire life cycle of the mine, substantially compromising the safety of mining operations. Identifying potential landslide areas and determining the landslide mechanism is crucial for the safety production and slope management of mines. This study proposes a combination of satellite radar interferometry measurement and numerical simulation to determine the landslide mechanism of the bedding-controlled slope in open-pit mines. First, the multidimensional small baseline subset (MSBAS) technique of interferometric synthetic aperture radar (InSAR) is used to capture deformation information in the vertical and east–west directions of the slope, locate large-scale and long-term movements, and preliminarily determine the trend of landslides. Then, a layered slope damage constitutive model is established, and a three-dimensional stability calculation of the layered slope is performed using COMSOL Multiphysics 5.3 software based on the strength reduction method to study the development and evolution process of landslides. The effectiveness of the method is validated by a large-scale bedding-controlled slope failure in the Nanfen open-pit mine in Liaoning, China, revealing the failure mechanism of the slope under excavation conditions. The study shows that the eastern slope bedding-controlled landslide in the Nanfen open-pit mine is a multizone composite-mode landslide caused by excavation, which belongs to the shear–slip–tension deformation failure mechanism as a whole. This study provides a new method for analyzing the mechanism of layered rock slope landslides under mining activities in open-pit mines, which can be used to assess and predict similar landslides.

Surface movement under the combined mining of open-pit and underground caving is the main problem affecting safe and efficient mining. Taking the combined mining of Dahongshan Iron Mine as an example, a mechanical model for calculating surface movement range was established to reveal the movement mechanism. The topography, the caving zone, the gravel filling of the caving zone and mining depth were considered, and the surface principal stress was calculated. Based on the mechanical model, the mechanical relationship between the subsidence angle and the surface cracking range was established and the definition of subsidence angle was supplemented: the subsidence angle is the angle measured from the horizontal of the moving boundary line, a straight line with zero displacement from the edge of the deepest extraction level to the surface and the largest surface cracking range. A trial calculation method for calculating the subsidence angle was proposed: by presetting different subsidence angles, the subsidence angle corresponding to the maximum surface prone cracking range calculated by mechanical model was found as the real subsidence angle. The subsidence angle calculated by the mechanical model was 60°, consistent with the observed subsidence angle of 64° in the Dahongshan Iron Mine, which verifies the reliability of the model.