Damir Nožica
Damir Nožica has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Damir Blažević
Faculty of Electrical Engineering, Computer Science and Information Technology Osijek, Josip Juraj Strossmayer University of Osijek, Kneza Trpimira 2b, 31000 Osijek, Croatia
6 shared publications - Tomislav Keser
Faculty of Electrical Engineering, Computer Science and Information Technology Osijek, Josip Juraj Strossmayer University of Osijek, Kneza Trpimira 2b, 31000 Osijek, Croatia
6 shared publications - Andrej Horvat
Quantium d.o.o., 31000 Osijek, Croatia
4 shared publications
Latest Publications
- Open Access
- 16 November 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (22) , 11340
PV Module Arrangement and Energy Yield Optimization Based on Flash List and Environmental Data
Mismatch losses in the electrical characteristics of photovoltaic (PV) modules depend on how the modules are arranged in arrays and on maximum power point tracking (MPPT) inputs. In practice, the arrangement is most often determined by sorting the modules according to one parameter from the flash list, or arranging panels as-delivered on pallets. The paper proposes a genetic algorithm (GA) that allocates modules to inverters, MPPT inputs and arrays in such a way as to maximize the annual energy yield (GAAEY). Each module is described by a double-diode model (DDM) whose parameters are determined from the flash list and then recalculated to operating conditions obtained from PVGIS-SARAH3 hourly data for the period 2005–2023 for Osijek, Croatia. The method was tested on five batches of 136 modules, each with a nominal power from 250 to 635 W, in a configuration with two inverters, two MPPT inputs per inverter and two strings of 17 modules per MPPT input. Since the physical effort involved in positioning modules on the construction site is the same for any layout, and calculating a GA-based layout takes several minutes, the practical benchmark is a comparison with installing modules as-delivered on pallets, rather than using the best sorting heuristic. Compared to modules connected in the as-delivered order, the GAAEY increases annual yield by 2.7 to 44.4 kWh, and compared to a random arrangement, it eliminates 91–96% of mismatch losses. A GA optimized for power at standard test conditions (STC) (GASTC) trails the GAAEY by 0.6–2.9 kWh per year, primarily due to higher losses at low irradiance.
- 16 November 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (22) , 11340
Open AccessPV Module Arrangement and Energy Yield Optimization Based on Flash List and Environmental Data
Mismatch losses in the electrical characteristics of photovoltaic (PV) modules depend on how the modules are arranged in arrays and on maximum power point tracking (MPPT) inputs. In practice, the arrangement is most often determined by sorting the modules according to one parameter from the flash list, or arranging panels as-delivered on pallets. The paper proposes a genetic algorithm (GA) that allocates modules to inverters, MPPT inputs and arrays in such a way as to maximize the annual energy yield (GAAEY). Each module is described by a double-diode model (DDM) whose parameters are determined from the flash list and then recalculated to operating conditions obtained from PVGIS-SARAH3 hourly data for the period 2005–2023 for Osijek, Croatia. The method was tested on five batches of 136 modules, each with a nominal power from 250 to 635 W, in a configuration with two inverters, two MPPT inputs per inverter and two strings of 17 modules per MPPT input. Since the physical effort involved in positioning modules on the construction site is the same for any layout, and calculating a GA-based layout takes several minutes, the practical benchmark is a comparison with installing modules as-delivered on pallets, rather than using the best sorting heuristic. Compared to modules connected in the as-delivered order, the GAAEY increases annual yield by 2.7 to 44.4 kWh, and compared to a random arrangement, it eliminates 91–96% of mismatch losses. A GA optimized for power at standard test conditions (STC) (GASTC) trails the GAAEY by 0.6–2.9 kWh per year, primarily due to higher losses at low irradiance.
- Open Access
Parameter Extraction for a Double-Diode PV Module Model Using Differential Evolution
This paper represents the expansion of the parameter extraction method for a photovoltaic module based on differential evolution (DE) developed for the double-diode model (DDM). DDM takes into account two diodes that model the recombination losses in the depleted layer, which means that the model has seven unknown parameters. By fixing the diode ideality factors and analytically eliminating the saturation current of the first diode and the photocurrent from the boundary conditions defined by the data given from the manufacturer’s datasheet, the dimensionality of the DE search comes down from seven to three parameters. The proposed approach is compared and validated using a single well-known multicrystalline KC200GT module. The results show that the proposed method achieves RMSE of 0.078627 A and NRMSE of 1.1520%, while Moshksar’s method achieves RMSE of 0.078783 A and NRMSE of 1.1543% for standard test conditions.
Open AccessParameter Extraction for a Double-Diode PV Module Model Using Differential Evolution
This paper represents the expansion of the parameter extraction method for a photovoltaic module based on differential evolution (DE) developed for the double-diode model (DDM). DDM takes into account two diodes that model the recombination losses in the depleted layer, which means that the model has seven unknown parameters. By fixing the diode ideality factors and analytically eliminating the saturation current of the first diode and the photocurrent from the boundary conditions defined by the data given from the manufacturer’s datasheet, the dimensionality of the DE search comes down from seven to three parameters. The proposed approach is compared and validated using a single well-known multicrystalline KC200GT module. The results show that the proposed method achieves RMSE of 0.078627 A and NRMSE of 1.1520%, while Moshksar’s method achieves RMSE of 0.078783 A and NRMSE of 1.1543% for standard test conditions.
- Open Access
- 5 October 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (19) , 9854
Mismatch Loss Optimization in PV Panel Arrays Using a Metaheuristic Approach
When two photovoltaic (PV) strings are connected in parallel to a single maximum power point tracker (MPPT) input, the tracker enforces one operating voltage on both strings, and whichever string is displaced from its own maximum power point contributes a power deficit. This loss is distinct from, and additive to, the mismatch loss arising among series-connected modules within each string. This work quantifies the two contributions separately and proposes a genetic algorithm (GA) that assigns modules from a real manufacturer flash list to strings and MPPT inputs so as to maximize the power delivered at the tracker, rather than the power of each string to be considered in isolation. Each module is represented by a double-diode model with parameters extracted from its flash list entry using a hybrid differential evolution procedure. String characteristics are obtained by summing module voltages at common current, and MPPT characteristics are obtained by summing string current at common voltage, so that the objective function evaluates the true interconnected operating point. For 68 modules of a 43.5 kW array, the mismatch loss is 0.398 W with separate MPPT inputs and 1.534 W with two strings per input. In the first case, sorting by MPP current lies within 0.122 W of the GA; in the second, all six criteria fall within 1.069 W of one another, random grouping ranks second, and the GA gains 3.243 W over the best of them. Sorting by a single parameter thus redistributes the loss between levels rather than removing it.
- 5 October 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (19) , 9854
Open AccessMismatch Loss Optimization in PV Panel Arrays Using a Metaheuristic Approach
When two photovoltaic (PV) strings are connected in parallel to a single maximum power point tracker (MPPT) input, the tracker enforces one operating voltage on both strings, and whichever string is displaced from its own maximum power point contributes a power deficit. This loss is distinct from, and additive to, the mismatch loss arising among series-connected modules within each string. This work quantifies the two contributions separately and proposes a genetic algorithm (GA) that assigns modules from a real manufacturer flash list to strings and MPPT inputs so as to maximize the power delivered at the tracker, rather than the power of each string to be considered in isolation. Each module is represented by a double-diode model with parameters extracted from its flash list entry using a hybrid differential evolution procedure. String characteristics are obtained by summing module voltages at common current, and MPPT characteristics are obtained by summing string current at common voltage, so that the objective function evaluates the true interconnected operating point. For 68 modules of a 43.5 kW array, the mismatch loss is 0.398 W with separate MPPT inputs and 1.534 W with two strings per input. In the first case, sorting by MPP current lies within 0.122 W of the GA; in the second, all six criteria fall within 1.069 W of one another, random grouping ranks second, and the GA gains 3.243 W over the best of them. Sorting by a single parameter thus redistributes the loss between levels rather than removing it.
- Open Access
- 30 September 2026
- Published by University Library in Kragujevac in Advanced Engineering Letters
- Vol. 5 (3) , 117
Comparative Assessment of Differential Evolution-Based and Analytical Parameter Extraction for Single-Diode PV Models Using Measured Data
This paper compares a single-diode model (SDM) parameter extraction method based on differential evolution (DE) with the analytical Villalva method, using a selected set of current-voltage (I-V) curves from the publicly available Sandia flash test dataset. The paper examines the methods’ applicability to experimentally measured curves from commercial photovoltaic (PV) modules. The SDM DE method analytically eliminates parameters from five to three, uses a Newton-Raphson solver for the implicit I-V characteristic, and minimises an objective function based on the error at the maximum power point. The results show that the proposed method achieves a lower root mean square error (RMSE) and normalized root mean square error (NRMSE) than the Villalva method across all tested curves, though at a higher computational cost.
- 30 September 2026
- Published by University Library in Kragujevac in Advanced Engineering Letters
- Vol. 5 (3) , 117
Open AccessComparative Assessment of Differential Evolution-Based and Analytical Parameter Extraction for Single-Diode PV Models Using Measured Data
This paper compares a single-diode model (SDM) parameter extraction method based on differential evolution (DE) with the analytical Villalva method, using a selected set of current-voltage (I-V) curves from the publicly available Sandia flash test dataset. The paper examines the methods’ applicability to experimentally measured curves from commercial photovoltaic (PV) modules. The SDM DE method analytically eliminates parameters from five to three, uses a Newton-Raphson solver for the implicit I-V characteristic, and minimises an objective function based on the error at the maximum power point. The results show that the proposed method achieves a lower root mean square error (RMSE) and normalized root mean square error (NRMSE) than the Villalva method across all tested curves, though at a higher computational cost.
- Open Access
- 15 April 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (8) , 4355
Industrial-Grade Edge Computing Device for Smart Furniture Products
As Internet of Things (IoT), communication convergence, and distributed computing are maturing, many new solutions are invented or derived every day, bringing new products and services to society. This paper elaborates on an industrial-grade information technology (IT) component upgrade to an existing ESP32 IoT device and the addition of new data communication layers to its capabilities. The aim of this research is to explore and propose new IT products to upgrade the first-generation smart furniture product. The proposed upgrades postulate a technological leap ahead in terms of (1) connectivity; (2) connection security; (3) product life-cycle management; and (4) integration (including sustainable product development). A distinct difference from the existing solution is presented in the aforementioned categories. The research points to a possible product that accommodates requirements and a niche of products that can be used, while eliminating other form factors. The process itself proves a point in the favor of the chosen IT product, providing confirmation of the hypotheses. Even though software and application security are not focal points of the discussion in this paper, these elements are generally presented as their presence is necessary in the modern convergence of communication methods.
- 15 April 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (8) , 4355
Open AccessIndustrial-Grade Edge Computing Device for Smart Furniture Products
As Internet of Things (IoT), communication convergence, and distributed computing are maturing, many new solutions are invented or derived every day, bringing new products and services to society. This paper elaborates on an industrial-grade information technology (IT) component upgrade to an existing ESP32 IoT device and the addition of new data communication layers to its capabilities. The aim of this research is to explore and propose new IT products to upgrade the first-generation smart furniture product. The proposed upgrades postulate a technological leap ahead in terms of (1) connectivity; (2) connection security; (3) product life-cycle management; and (4) integration (including sustainable product development). A distinct difference from the existing solution is presented in the aforementioned categories. The research points to a possible product that accommodates requirements and a niche of products that can be used, while eliminating other form factors. The process itself proves a point in the favor of the chosen IT product, providing confirmation of the hypotheses. Even though software and application security are not focal points of the discussion in this paper, these elements are generally presented as their presence is necessary in the modern convergence of communication methods.
- 1 March 2023
- Published by University Library in Kragujevac in Advanced Engineering Letters
- Vol. 2 (1) , 28-40
LORA COMMUNICATION MAINTENANCE AND SIGNAL PROPAGATION EVALUATION IN OBSTACLE-DENSE INDUSTRIAL ENVIRONMENTS: A WOOD PROCESSING APPLICATION
Using various wireless communication methods to achieve some type of remote monitoring and/or controlling of processes and systems, in general, is a continuously thriving industry. The wood industry is not immune to that but the prevalence of such systems, automated to a certain level, remains low. Their rise and presence, however, are unavoidable and will continue to grow. Wireless devices are used to continuously monitor environmental factors as well as the structural moisture of wood in a wooden plank during the natural aspirated drying process and the forced drying process all in a controlled environment. An exemplary system based on LoRa communication interfaces is configured, adapted, and operationally tuned for the wood processing industry. The selected LoRa communication system operates on an EU compliant RF spectrum. Nevertheless, since such devices must be tightly integrated within a pack of planks, wireless signal propagation is greatly impacted. The pack of planks has an effect on radio signal dispersion because it creates a dense environment hostile to RF propagation. A technique to strengthen measurement devices and receive units for wireless signal propagation is proposed in order to maintain a high-quality communication link. Furthermore, practical procedures for maintaining a desirable signal level and their upkeep suggestions are presented for applications with numerous obstacles in the working environment.
- 1 March 2023
- Published by University Library in Kragujevac in Advanced Engineering Letters
- Vol. 2 (1) , 28-40
LORA COMMUNICATION MAINTENANCE AND SIGNAL PROPAGATION EVALUATION IN OBSTACLE-DENSE INDUSTRIAL ENVIRONMENTS: A WOOD PROCESSING APPLICATION
Using various wireless communication methods to achieve some type of remote monitoring and/or controlling of processes and systems, in general, is a continuously thriving industry. The wood industry is not immune to that but the prevalence of such systems, automated to a certain level, remains low. Their rise and presence, however, are unavoidable and will continue to grow. Wireless devices are used to continuously monitor environmental factors as well as the structural moisture of wood in a wooden plank during the natural aspirated drying process and the forced drying process all in a controlled environment. An exemplary system based on LoRa communication interfaces is configured, adapted, and operationally tuned for the wood processing industry. The selected LoRa communication system operates on an EU compliant RF spectrum. Nevertheless, since such devices must be tightly integrated within a pack of planks, wireless signal propagation is greatly impacted. The pack of planks has an effect on radio signal dispersion because it creates a dense environment hostile to RF propagation. A technique to strengthen measurement devices and receive units for wireless signal propagation is proposed in order to maintain a high-quality communication link. Furthermore, practical procedures for maintaining a desirable signal level and their upkeep suggestions are presented for applications with numerous obstacles in the working environment.