Lei Bu

The electromechanical transmission (EMT) systems of hybrid special vehicles are highly susceptible to severe transient torsional resonance under frequent start-stop operating conditions. Traditional entire-frequency domain H_∞ active vibration reduction strategies are often limited by insufficient gain, failing to achieve ultimate suppression within the core resonance frequency band. To address this issue, this paper proposes a finite-frequency H_∞ active torsional vibration suppression strategy based on a motor dual-loop control architecture. This strategy achieves a profound physical decoupling between torsional vibration suppression and steady-state driving tasks. Furthermore, by introducing the Generalized Kalman–Yakubovich–Popov (GKYP) lemma and Linear Matrix Inequalities (LMIs) into the secondary loop, the control degrees of freedom are precisely concentrated on the 8–30 Hz frequency band, where the transient resonance energy is highly localized. This thoroughly eliminates the conservatism inherent in entire-frequency designs. To mitigate the instability risks caused by unmeasurable states and actuator response lags in practical engineering applications, a robust controller integrating input time-delay compensation and dynamic output feedback is subsequently constructed. Numerical case studies and hardware-in-the-loop (HIL) test results based on a specific EMT configuration demonstrate that the proposed strategy effectively overcomes the instability induced by system delays. It achieves an outstanding resonance peak attenuation of up to 93% and strictly constrains output shaft torque fluctuations within a safe threshold of 50 N·m. Ultimately, this study provides an efficient and robust closed-loop engineering solution for the transient vibration management of high-power electromechanical transmission systems and the enhancement of overall vehicle NVH performance.

Power-split hybrid electric vehicles (power-split-HEVs) exhibit significant engine torque fluctuations due to their mechanical coupling with the driveline, leading to pronounced torsional vibration issues in the drive shaft. This study investigates an active torsional vibration suppression strategy based on drive motor control. First, a dynamic model of the power-split-HEV driveline is established, and its intrinsic characteristics are analyzed. Subsequently, an engine excitation torque model is developed to identify the dominant response orders, while a vehicle dynamics model is constructed to elucidate the torsional vibration mechanisms in both hybrid and pure electric driving modes. Next, a torsional vibration feedback control framework is proposed, utilizing the electric motor as a secondary-channel torque disturbance compensator. Furthermore, a novel frequency-decoupled dual-loop control framework is proposed, with rigorous derivation of the sufficient conditions for decoupling. Based on this framework, two distinct vibration suppression algorithms are developed for the secondary-loop controller, each tailored for specific operational modes. Finally, the proposed algorithms are validated through simulation and hardware-in-the-loop (HIL) testing. The results demonstrate a torque fluctuation suppression ratio of up to 72.2%, confirming that the active suppression algorithm effectively mitigates driveline torsional vibration induced by engine harmonic torque disturbances.

To improve the wear resistance of TC4 titanium alloy, two types of wear-resistant coatings were applied to the surface using laser melting: Ni60 + 50% WC and d22 powder priming. The phase composition and microstructure of the coatings were characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM), and energy spectroscopy (EDS). The mechanical properties of the coating were tested using an HV-1000 micro-Vickers hardness tester, an HRS-2M high-speed reciprocating friction and wear tester, and a WDW-100D electronic universal testing machine. The results show that Ni60 + 50% WC composite coating and d22 priming + (Ni60 + 50% WC) composite coating mainly consist of W₂C, TiC, Ni₁₇W₃, Ni₃Ti, and Ti_xW_1−x phases. Compared to the TC4 substrate, the microhardness of both coatings is significantly higher, approximately 2.8 times the microhardness of the substrate. In frictional wear experiments, the average friction factors of the two coatings and the TC4 substrate are 0.476, 0.55, and 0.865, respectively, and the wear of the two coatings is only 0.0559–0.0769 that of the TC4 substrate, with a significant increase in wear resistance, nearly 17 times higher than that of the substrate. The coating shows flaking, shallow abrasion marks, and granular debris, dominated by adhesive wear and fatigue wear, while the TC4 substrate shows more furrows on the surface, dominated by abrasive wear. The shear bond strengths of the Ni60 + 50% WC composite coating and the d22 powder primed + (Ni60 + 50% WC) composite coating were 188.19 MPa and 49.11 MPa, respectively. Conclusion: both coatings significantly improve the hardness and wear resistance of the TC4 titanium alloy substrate surface, with the Ni60 + 50% WC composite coating performing better in hardness, wear resistance, and bond strength.

To overcome the detrimental effect of residual stress in welded joints, which affects the overall performance of the welded structure, this paper studies the magnitude and distribution of residual stress after welding and local post-weld heat treatment (PWHT). The coupled thermo-metallurgical-mechanical model for welding 6 mm thick Ti-6Al-4V (TC4) titanium alloy plates was established, the evolution of the SSPT and its effect on the residual stress were quantitatively analyzed, and a parametric analysis of local PWHT was performed. The results demonstrated that there was good agreement between the numerical results and the experimental data. Due to the cooling rate reaching 327 °C/s, the volume fraction of α^、 in the fusion zone (FZ) reached 0.218 after welding and decreased by 90.83% after PWHT when the heating temperature was 700 °C. The peak value of the longitudinal residual stress can reach 686.4 MPa after welding with SSPT, which was 11.38% lower than that without SSPT, and it decreased by 65.6% after PWHT when the heating temperature was 900 °C. The research results demonstrate that SSPT has a significant effect on residual stress, and PWHT can obviously reduce the residual stress, which provides a certain reference for welding TC4 titanium alloy plates.

The actual driving conditions of electric vehicles (EVs) are complex and changeable. Limited by road adhesion conditions, it is necessary to give priority to ensuring safety, taking into account the energy recovery ratio of the vehicle during braking to obtain better braking quality. In this work, an electric vehicle with an EHB (electro-hydraulic braking) system whose braking force adaptive distribution control strategy is studied. Firstly, the vehicle dynamics model, including seven degrees of freedom, tire, drive motor, main reducer, battery pack, and braking system, was constructed, which is attributed to the vehicle configuration and braking system scheme. Second, based on curve I and ECE regulations, the adaptive braking force distribution control strategy was formulated by taking the maximum regenerative braking torque as the inflection point, the synchronous adhesion coefficient as the desired point, and the battery SOC, road adhesion coefficient, and braking strength as the threshold. Finally, the vehicle dynamics simulation model was built on the Matlab/Simulink platform, and the simulation results verified the feasibility of the proposed braking force adaptive allocation control strategy. The research shows that the adaptive distribution control strategy can better adapt to the complex and variable driving conditions of the vehicle by combining the inflection point and the desired point. The braking energy recovery ratios of the vehicle under the NEDC and NYCC cycle conditions on a high adhesion road are 52.62% and 47.45%. The braking force distribution curve is close to curve I under the low adhesion extreme road.