Abdollah Tabaroei
Abdollah Tabaroei has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Minh Tuan Pham
Department of Civil and Architectural Engineering, KTH Royal Institute of Technology, Stockholm, Sweden
5 shared publications Vahab Sarfarazi
DEPARTMENT OF MINING ENGINEERING, HAMEDAN UNIVERSITY OF TECHNOLOGY, HAMEDAN, IRAN
3 shared publications- Yang Zhao
State Key Laboratory of Geomechanics and Geotechnical Engineering Safety, Institute of Rock and Soil Mechanics, Chinese Academy of Sciences, Wuhan, China
3 shared publications Amir Hossein Vakili
Department of Civil Environmental Engineering, Faculty of Engineering, Zand Institute of Higher Education, Shiraz, Iran
2 shared publications- Ankit Garg
Department of Health and Environmental Science, Xi’an Jiaotong Liverpool University, Suzhou, China
2 shared publications - Maziar Moaveni
Associate Professor, Dept. of Engineering Technology, Savannah state Univ., Savannah, GA 31404. ORCID:
2 shared publications
Latest Publications
- Open Access
- 2 November 2026
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 44 (9) , 435
Correction: Settlement and Mobilized Bearing Capacity of Circular Footings on Geosynthetic-Reinforced Sand: Experimental and Numerical Study
- 2 November 2026
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 44 (9) , 435
Open AccessCorrection: Settlement and Mobilized Bearing Capacity of Circular Footings on Geosynthetic-Reinforced Sand: Experimental and Numerical Study
- Open Access
- 29 July 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
2D finite-element analysis of back-to-back mechanically stabilized earth walls
- 29 July 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open Access2D finite-element analysis of back-to-back mechanically stabilized earth walls
- Open Access
- 23 July 2026
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 44 (6) , 310
Correction: Settlement and Mobilized Bearing Capacity of Circular Footings on Geosynthetic-Reinforced Sand: Experimental and Numerical Study
- 23 July 2026
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 44 (6) , 310
Open AccessCorrection: Settlement and Mobilized Bearing Capacity of Circular Footings on Geosynthetic-Reinforced Sand: Experimental and Numerical Study
- 11 May 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (40) , 42135-42158
A Physics-Informed Machine Learning Framework for Strength Prediction, Uncertainty Quantification, and Optimization of Chemically Stabilized Soils
- 11 May 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (40) , 42135-42158
A Physics-Informed Machine Learning Framework for Strength Prediction, Uncertainty Quantification, and Optimization of Chemically Stabilized Soils
- Open Access
- 29 April 2026
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 44 (4) , 197
Settlement and Mobilized Bearing Capacity of Circular Footings on Geosynthetic-Reinforced Sand: Experimental and Numerical Study
Circular footings are common in towers and tanks but their performance on geosynthetic-reinforced sands remains underexplored. We present an integrated experimental–numerical–analytical study using large-scale plate tests on geogrid-reinforced sand and validated 3D simulations extended to geocell reinforcement. The work delivers settlement-dependent performance maps and a bounded predictor for design. Geogrid tests show bearing improvement factors up to I f = 1.82 (for s/D > 5%) and PRS reductions up to 25%. Optimum ranges are u/D≈0.10–0.25, WD ≤ 1.5 (≈WD < 445 mm for D = 300 mm), with diminishing gains for N > 2. Numerical analyses reproduce experiments within ≈10% and reveal deeper mobilization of soil mass with geocells, explaining plateaus observed at large WD and depth. A settlement-dependent empirical equation is proposed with stated validity ranges and external validation (MAE ≤ 10–15%). The results provide mechanistic insight and practical guidance for circular foundations reinforced by geosynthetics, emphasizing when reinforcement is most effective and when densification or fewer layers suffice. This integrated approach advances understanding of soil–footing–reinforcement interaction and offers practical design guidance for circular foundations on granular soils.
- 29 April 2026
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 44 (4) , 197
Open AccessSettlement and Mobilized Bearing Capacity of Circular Footings on Geosynthetic-Reinforced Sand: Experimental and Numerical Study
Circular footings are common in towers and tanks but their performance on geosynthetic-reinforced sands remains underexplored. We present an integrated experimental–numerical–analytical study using large-scale plate tests on geogrid-reinforced sand and validated 3D simulations extended to geocell reinforcement. The work delivers settlement-dependent performance maps and a bounded predictor for design. Geogrid tests show bearing improvement factors up to I f = 1.82 (for s/D > 5%) and PRS reductions up to 25%. Optimum ranges are u/D≈0.10–0.25, WD ≤ 1.5 (≈WD < 445 mm for D = 300 mm), with diminishing gains for N > 2. Numerical analyses reproduce experiments within ≈10% and reveal deeper mobilization of soil mass with geocells, explaining plateaus observed at large WD and depth. A settlement-dependent empirical equation is proposed with stated validity ranges and external validation (MAE ≤ 10–15%). The results provide mechanistic insight and practical guidance for circular foundations reinforced by geosynthetics, emphasizing when reinforcement is most effective and when densification or fewer layers suffice. This integrated approach advances understanding of soil–footing–reinforcement interaction and offers practical design guidance for circular foundations on granular soils.
- Top Cited PapersOpen Access
- 3 January 2026
- Published by Elsevier in Computers and Geotechnics
- Vol. 192
Group efficiency and load transfer mechanisms of semi-rigid soil–cement piles: integrated experimental, 3D numerical, and analytical evaluation
- 3 January 2026
- Published by Elsevier in Computers and Geotechnics
- Vol. 192
Top Cited PapersOpen AccessGroup efficiency and load transfer mechanisms of semi-rigid soil–cement piles: integrated experimental, 3D numerical, and analytical evaluation
- Open Access
- 9 December 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (24) , 11002
Correction: BP et al. Methane Emission and Carbon Sequestration Potential from Municipal Solid Waste Landfill, India. Sustainability 2023, 15, 7125
The authors would like to make the following corrections to the published paper
- 9 December 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (24) , 11002
Open AccessCorrection: BP et al. Methane Emission and Carbon Sequestration Potential from Municipal Solid Waste Landfill, India. Sustainability 2023, 15, 7125
The authors would like to make the following corrections to the published paper
- Open Access
- 21 October 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-16
Mechanical and microstructural enhancement of clayey soils through recycled glass powder stabilization
In this paper, we use recycled glass powder (RGP) as a replacement of the soil to enhance the mechanical characteristics of the Mashhad clayey soil. For this purpose, a total of 60 unconfined compression tests and microstructural analyses including scanning electron microscopy (SEM) and x-ray diffraction (XRD) have been carried out on both of the unstabilized/stabilized RGP clayey soil specimens. The RGP contents used for replacing in the soil were 3% to 25% and the curing time were of 7 and 28 days, respectively. The results indicated that replacing RGP in clayey soil led to an increase in soil stiffness, unconfined compressive strength (UCS), maximum strain energy or energy absorption capacity (Eu), secant modulus (E50), resilient modulus (MR) and a decrease in the failure strain (εf) of the clayey soil mixture. The effect of increasing in the soil strength was more pronounced with RGP = 15% (optimum content) and more amount of curing times. The results obtained from the microstructural analysis were in full agreement with the findings obtained from UCS tests. The XRD tests indicated that the replacing of RGP = 15% with amorphous structure to the clays soil caused reduced the concentration of crystalline phases in the unstabilized soil specimens, leading to reduce in the intensity of the peaks. SEM results further emphasized that the microstructure of the clayey soil stabilized with RGP = 15% became more consolidated, with a noticeable reduction in the number and size of pores.
- 21 October 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-16
Open AccessMechanical and microstructural enhancement of clayey soils through recycled glass powder stabilization
In this paper, we use recycled glass powder (RGP) as a replacement of the soil to enhance the mechanical characteristics of the Mashhad clayey soil. For this purpose, a total of 60 unconfined compression tests and microstructural analyses including scanning electron microscopy (SEM) and x-ray diffraction (XRD) have been carried out on both of the unstabilized/stabilized RGP clayey soil specimens. The RGP contents used for replacing in the soil were 3% to 25% and the curing time were of 7 and 28 days, respectively. The results indicated that replacing RGP in clayey soil led to an increase in soil stiffness, unconfined compressive strength (UCS), maximum strain energy or energy absorption capacity (Eu), secant modulus (E50), resilient modulus (MR) and a decrease in the failure strain (εf) of the clayey soil mixture. The effect of increasing in the soil strength was more pronounced with RGP = 15% (optimum content) and more amount of curing times. The results obtained from the microstructural analysis were in full agreement with the findings obtained from UCS tests. The XRD tests indicated that the replacing of RGP = 15% with amorphous structure to the clays soil caused reduced the concentration of crystalline phases in the unstabilized soil specimens, leading to reduce in the intensity of the peaks. SEM results further emphasized that the microstructure of the clayey soil stabilized with RGP = 15% became more consolidated, with a noticeable reduction in the number and size of pores.
- Open Access
- 22 August 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-21
Developing new machine-learning intelligent models to predict the excavation-tunnel displacements
With the increase of urban development in big cities, the requirement for deep excavations to build the tall building foundations of has increased significantly. Depending on the dimension and location, these excavations can have an important effect on underground tunnels, especially subway tunnels. In order to get a better realization of the behavior of an existing tunnel due to a vicinity deep excavation, this research that consists of three main parts, propose new intelligent models for predicting the excavation-tunnel displacements using machine learning. For the purpose four equations present to predict displacements of the excavation-tunnel complex. In the first step, a three-dimensional (3D) finite-element (FE) model validate against case stories. In the second step, a number of three-hundred and sixty 3D simulations of an existing tunnel located directly beneath an excavation under different parameters such as excavation geometry and tunnel positions beneath the excavation were carried out. Finally in the third part, based on the simulation results two models developed for predict and validate the \({\delta }_{hrm}\), \({\delta }_{vm}\), \({\delta }_{htm}\) and \({\delta }_{vtm}\) values. Based on 3D FE results, the displacements mechanisms of the excavation-tunnel complex were presented. It was observed that the \(L/B\) ratio variation have a more effect on the \({\delta }_{hrm}\) values than \({\delta }_{vm}\). Additionally, the \({\delta }_{hrm}\) values occurs approximately in the middle \(1/3{H}_{w}\). The results demonstrate that when the tunnel located at very close beneath the excavation area, tunnel tends to move vertically towards the excavation area. As \({D}_{h}\) value increases, the vertical displacement values of the tunnel decrease. The proposed models validated against FE results the results show that the models has an acceptable performance in estimating the of excavation and tunnel displacements.- 22 August 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-21
Open AccessDeveloping new machine-learning intelligent models to predict the excavation-tunnel displacements
With the increase of urban development in big cities, the requirement for deep excavations to build the tall building foundations of has increased significantly. Depending on the dimension and location, these excavations can have an important effect on underground tunnels, especially subway tunnels. In order to get a better realization of the behavior of an existing tunnel due to a vicinity deep excavation, this research that consists of three main parts, propose new intelligent models for predicting the excavation-tunnel displacements using machine learning. For the purpose four equations present to predict displacements of the excavation-tunnel complex. In the first step, a three-dimensional (3D) finite-element (FE) model validate against case stories. In the second step, a number of three-hundred and sixty 3D simulations of an existing tunnel located directly beneath an excavation under different parameters such as excavation geometry and tunnel positions beneath the excavation were carried out. Finally in the third part, based on the simulation results two models developed for predict and validate the \({\delta }_{hrm}\), \({\delta }_{vm}\), \({\delta }_{htm}\) and \({\delta }_{vtm}\) values. Based on 3D FE results, the displacements mechanisms of the excavation-tunnel complex were presented. It was observed that the \(L/B\) ratio variation have a more effect on the \({\delta }_{hrm}\) values than \({\delta }_{vm}\). Additionally, the \({\delta }_{hrm}\) values occurs approximately in the middle \(1/3{H}_{w}\). The results demonstrate that when the tunnel located at very close beneath the excavation area, tunnel tends to move vertically towards the excavation area. As \({D}_{h}\) value increases, the vertical displacement values of the tunnel decrease. The proposed models validated against FE results the results show that the models has an acceptable performance in estimating the of excavation and tunnel displacements.