Hao Feng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hao Feng has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Yuping Zhao
School of Electronics, Peking University, Beijing, China
9 shared publications Yuting Xu
Peking University Shenzhen Graduate School, Peking University, Shenzhen, China
3 shared publications- Yuting Xu
Peking University
2 shared publications - Chuanchuan Yang
State Key Laboratory of Photonics and Communications, School of Electronics, Peking University, Beijing 100871, China
1 shared publication - Hongbin Li
State Key Laboratory of Photonics and Communications, School of Electronics, Peking University, Beijing 100871, China
1 shared publication - Jiqiang Feng
Shenzhen University
1 shared publication
Latest Publications
- 12 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Green Communications and Networking
- Vol. 10, 737-750
Knowledge Base Autoencoder Framework: A Novel Approach for Continuous Phase Shift Compression in RIS-Aided Communications
In a communication system assisted by reconfigurable intelligent surfaces (RIS), phase optimization on RIS is not feasible by itself because of its passive nature. Therefore, the base station (BS) must convey the optimized phase shift to RIS via a dedicated control channel. However, the large number of RIS unit cells results in a considerable number of phase shift parameters, occupying a substantial amount of signaling resources. To address this challenge, this paper proposes a novel knowledge base autoencoder (KBAE) framework for compressing continuous phase shifts in RIS-aided communications. The KBAE framework integrates a specially designed phase shift compression network (PSCNet) and a higher compression ratio version (PSCNet-H) to achieve high-efficiency phase shift compression. The scheme utilizes a learnable knowledge base to approximate the distribution of RIS phase shift features. It only needs to transmit the indexes of the vectors in the knowledge base that are most similar to the RIS phase shift feature. Simulation results demonstrated that the proposed scheme can significantly improve the reconstruction accuracy of RIS phase shift and the average achievable rate compared to the benchmark methods. These advancements highlight the potential of KBAE to enhance the scalability and performance of future wireless networks.
- 12 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Green Communications and Networking
- Vol. 10, 737-750
Knowledge Base Autoencoder Framework: A Novel Approach for Continuous Phase Shift Compression in RIS-Aided Communications
In a communication system assisted by reconfigurable intelligent surfaces (RIS), phase optimization on RIS is not feasible by itself because of its passive nature. Therefore, the base station (BS) must convey the optimized phase shift to RIS via a dedicated control channel. However, the large number of RIS unit cells results in a considerable number of phase shift parameters, occupying a substantial amount of signaling resources. To address this challenge, this paper proposes a novel knowledge base autoencoder (KBAE) framework for compressing continuous phase shifts in RIS-aided communications. The KBAE framework integrates a specially designed phase shift compression network (PSCNet) and a higher compression ratio version (PSCNet-H) to achieve high-efficiency phase shift compression. The scheme utilizes a learnable knowledge base to approximate the distribution of RIS phase shift features. It only needs to transmit the indexes of the vectors in the knowledge base that are most similar to the RIS phase shift feature. Simulation results demonstrated that the proposed scheme can significantly improve the reconstruction accuracy of RIS phase shift and the average achievable rate compared to the benchmark methods. These advancements highlight the potential of KBAE to enhance the scalability and performance of future wireless networks.
- 23 July 2025
- Published by Springer Nature
- p. 131-142
Lightweight CSI Feedback with Global Context Attention for RIS-Assisted Communications
- 23 July 2025
- Published by Springer Nature
- p. 131-142
Lightweight CSI Feedback with Global Context Attention for RIS-Assisted Communications
- Open Access
- 1 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Communications and Networks
- Vol. 26 (4) , 424-432
A full-duplex technology based on the Doppler effect
Full-duplex technology can improve bandwidth and energy efficiency but has serious self-interference. In this paper, we introduce a novel full-duplex communication scheme that leverages the Doppler effect. By rotating the circular antenna array, the Doppler frequency shift is introduced into the received uplink (UL) signal, and the UL signal can be separated from the downlink (DL) signal in the frequency domain, thus eliminating self-interference. In order to maximize the interference-free bandwidth, an antenna switching criterion to maximum frequency offset interval is proposed for antenna switching control. Moreover, an antenna switching module based on the above criterion and a Doppler frequency shift compensation module are designed. Simulation results show that the proposed scheme can effectively avoid interference between UL and DL signals and achieves a substantial capacity improvement compared to conventional systems.
- 1 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Communications and Networks
- Vol. 26 (4) , 424-432
Open AccessA full-duplex technology based on the Doppler effect
Full-duplex technology can improve bandwidth and energy efficiency but has serious self-interference. In this paper, we introduce a novel full-duplex communication scheme that leverages the Doppler effect. By rotating the circular antenna array, the Doppler frequency shift is introduced into the received uplink (UL) signal, and the UL signal can be separated from the downlink (DL) signal in the frequency domain, thus eliminating self-interference. In order to maximize the interference-free bandwidth, an antenna switching criterion to maximum frequency offset interval is proposed for antenna switching control. Moreover, an antenna switching module based on the above criterion and a Doppler frequency shift compensation module are designed. Simulation results show that the proposed scheme can effectively avoid interference between UL and DL signals and achieves a substantial capacity improvement compared to conventional systems.
- 17 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 73 (11) , 17875-17880
Knowledge Base-Based High Compression Ratio CSI Feedback for RIS-Assisted mmWave Communications
Reconfigurable intelligent surface (RIS) has emerged as a pivotal technology in future wireless communication, which can expand millimeter wave signal coverage and enhance communication system performance. In frequency division duplex systems, the user equipment is required to provide channel state information (CSI) to the base station through a feedback channel. However, a substantial number of unit cells in RIS results in increased CSI feedback, consuming bandwidth and time resources. This correspondence proposes a knowledge base-based high compression ratio CSI feedback scheme (Knowledge Base Network, KBNet) for millimeter wave RIS-assisted wireless communication. The scheme employs a learnable knowledge base to approximate the distribution of CSI features and only needs to transmit the indexes of the vectors in the knowledge base that are most similar to the CSI feature, which can achieve accurate recovery of CSI under the condition of improving compression ratio. Simulation results demonstrate that the proposed scheme significantly improves channel recovery accuracy compared to benchmark methods under high compression ratios while efficiently reducing model size and computational complexity.
- 17 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 73 (11) , 17875-17880
Knowledge Base-Based High Compression Ratio CSI Feedback for RIS-Assisted mmWave Communications
Reconfigurable intelligent surface (RIS) has emerged as a pivotal technology in future wireless communication, which can expand millimeter wave signal coverage and enhance communication system performance. In frequency division duplex systems, the user equipment is required to provide channel state information (CSI) to the base station through a feedback channel. However, a substantial number of unit cells in RIS results in increased CSI feedback, consuming bandwidth and time resources. This correspondence proposes a knowledge base-based high compression ratio CSI feedback scheme (Knowledge Base Network, KBNet) for millimeter wave RIS-assisted wireless communication. The scheme employs a learnable knowledge base to approximate the distribution of CSI features and only needs to transmit the indexes of the vectors in the knowledge base that are most similar to the CSI feature, which can achieve accurate recovery of CSI under the condition of improving compression ratio. Simulation results demonstrate that the proposed scheme significantly improves channel recovery accuracy compared to benchmark methods under high compression ratios while efficiently reducing model size and computational complexity.
- 13 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Communications Letters
- Vol. 28 (8) , 1860-1864
Deep Learning-Based Joint Channel Estimation and CSI Feedback for RIS-Assisted Communications
In reconfigurable intelligent surface (RIS)-assisted communication systems, downlink channel state information (CSI) is essential for designing beamforming at both the base station and the RIS. Hence, accurate downlink channel estimation and CSI feedback are crucial for ensuring optimal system performance. Current methods focus on independently enhancing the processes of channel estimation and CSI feedback. However, this separate optimization strategy is inefficient and introduces errors from the previous process into the subsequent one, resulting in degraded system performance. To address this issue, this letter presents a novel deep learning-based joint channel estimation and CSI feedback scheme named JDCNet for RIS-assisted communications. This scheme directly incorporates preliminary channel estimation with errors into the compression and feedback process, enabling the joint design and optimization of these two critical tasks. Simulation results demonstrate that the proposed scheme outperforms benchmark methods regarding channel reconstruction accuracy while significantly reducing time and space complexity.
- 13 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Communications Letters
- Vol. 28 (8) , 1860-1864
Deep Learning-Based Joint Channel Estimation and CSI Feedback for RIS-Assisted Communications
In reconfigurable intelligent surface (RIS)-assisted communication systems, downlink channel state information (CSI) is essential for designing beamforming at both the base station and the RIS. Hence, accurate downlink channel estimation and CSI feedback are crucial for ensuring optimal system performance. Current methods focus on independently enhancing the processes of channel estimation and CSI feedback. However, this separate optimization strategy is inefficient and introduces errors from the previous process into the subsequent one, resulting in degraded system performance. To address this issue, this letter presents a novel deep learning-based joint channel estimation and CSI feedback scheme named JDCNet for RIS-assisted communications. This scheme directly incorporates preliminary channel estimation with errors into the compression and feedback process, enabling the joint design and optimization of these two critical tasks. Simulation results demonstrate that the proposed scheme outperforms benchmark methods regarding channel reconstruction accuracy while significantly reducing time and space complexity.
- 15 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Green Communications and Networking
- Vol. 8 (4) , 1943-1954
Active RIS-Assisted mmWave Indoor Signal Enhancement Based on Transparent RIS
Due to the substantial path loss inherent to millimeter-wave (mmWave) frequencies, the signal sent by the outdoor base station is seriously attenuated when it reaches the indoors. Recent research has introduced a glass-based metasurface to enhance mmWave signals in indoor settings. While a transparent reconfigurable intelligent surface (RIS) can focus signals in specific areas, achieving ideal coverage is hindered by constraints such as building structures. To address this limitation, we propose a novel RIS-assisted mmWave indoor enhancement scheme in which a transparent RIS is deployed on the glass, and a reflection RIS is introduced to enhance signal connectivity, ensuring mmWave coverage across indoor spaces. Three distinct assisted transmission scenarios are considered in this proposed scheme: passive RIS (PRIS), active RIS (ARIS), and hybrid RIS (HRIS). This paper aims to maximize the signal-to-noise ratio (SNR) of the received signal for the three assisted transmission scenarios. The closed-form solution is presented in the PRIS and the ARIS-assisted transmission scenarios. In addition, the performance of the proposed scheme is analyzed under three assisted transmission scenarios. The results indicate that the ARIS-assisted transmission scenario achieves the highest data rate and energy efficiency under a smaller transmit power while demanding minimal unit cells.
- 15 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Green Communications and Networking
- Vol. 8 (4) , 1943-1954
Active RIS-Assisted mmWave Indoor Signal Enhancement Based on Transparent RIS
Due to the substantial path loss inherent to millimeter-wave (mmWave) frequencies, the signal sent by the outdoor base station is seriously attenuated when it reaches the indoors. Recent research has introduced a glass-based metasurface to enhance mmWave signals in indoor settings. While a transparent reconfigurable intelligent surface (RIS) can focus signals in specific areas, achieving ideal coverage is hindered by constraints such as building structures. To address this limitation, we propose a novel RIS-assisted mmWave indoor enhancement scheme in which a transparent RIS is deployed on the glass, and a reflection RIS is introduced to enhance signal connectivity, ensuring mmWave coverage across indoor spaces. Three distinct assisted transmission scenarios are considered in this proposed scheme: passive RIS (PRIS), active RIS (ARIS), and hybrid RIS (HRIS). This paper aims to maximize the signal-to-noise ratio (SNR) of the received signal for the three assisted transmission scenarios. The closed-form solution is presented in the PRIS and the ARIS-assisted transmission scenarios. In addition, the performance of the proposed scheme is analyzed under three assisted transmission scenarios. The results indicate that the ARIS-assisted transmission scenario achieves the highest data rate and energy efficiency under a smaller transmit power while demanding minimal unit cells.
- Top Cited PapersOpen Access
- 4 October 2023
- Published by Wiley in Nanophotonics
- Vol. 12 (20) , 3871-3881
Diffusion probabilistic model based accurate and high‐degree‐of‐freedom metasurface inverse design
Conventional meta‐atom designs rely heavily on researchers’ prior knowledge and trial‐and‐error searches using full‐wave simulations, resulting in time‐consuming and inefficient processes. Inverse design methods based on optimization algorithms, such as evolutionary algorithms, and topological optimizations, have been introduced to design metamaterials. However, none of these algorithms are general enough to fulfill multi‐objective tasks. Recently, deep learning methods represented by generative adversarial networks (GANs) have been applied to inverse design of metamaterials, which can directly generate high‐degree‐of‐freedom meta‐atoms based on S‐parameters requirements. However, the adversarial training process of GANs makes the network unstable and results in high modeling costs. This paper proposes a novel metamaterial inverse design method based on the diffusion probability theory. By learning the Markov process that transforms the original structure into a Gaussian distribution, the proposed method can gradually remove the noise starting from the Gaussian distribution and generate new high‐degree‐of‐freedom meta‐atoms that meet S‐parameters conditions, which avoids the model instability introduced by the adversarial training process of GANs and ensures more accurate and high‐quality generation results. Experiments have proven that our method is superior to representative methods of GANs in terms of model convergence speed, generation accuracy, and quality.
- 4 October 2023
- Published by Wiley in Nanophotonics
- Vol. 12 (20) , 3871-3881
Top Cited PapersOpen AccessDiffusion probabilistic model based accurate and high‐degree‐of‐freedom metasurface inverse design
Conventional meta‐atom designs rely heavily on researchers’ prior knowledge and trial‐and‐error searches using full‐wave simulations, resulting in time‐consuming and inefficient processes. Inverse design methods based on optimization algorithms, such as evolutionary algorithms, and topological optimizations, have been introduced to design metamaterials. However, none of these algorithms are general enough to fulfill multi‐objective tasks. Recently, deep learning methods represented by generative adversarial networks (GANs) have been applied to inverse design of metamaterials, which can directly generate high‐degree‐of‐freedom meta‐atoms based on S‐parameters requirements. However, the adversarial training process of GANs makes the network unstable and results in high modeling costs. This paper proposes a novel metamaterial inverse design method based on the diffusion probability theory. By learning the Markov process that transforms the original structure into a Gaussian distribution, the proposed method can gradually remove the noise starting from the Gaussian distribution and generate new high‐degree‐of‐freedom meta‐atoms that meet S‐parameters conditions, which avoids the model instability introduced by the adversarial training process of GANs and ensures more accurate and high‐quality generation results. Experiments have proven that our method is superior to representative methods of GANs in terms of model convergence speed, generation accuracy, and quality.
- Open Access
Active RIS-Assisted mmWave Indoor Signal Enhancement Based on Transparent RIS
Due to the serious path loss of millimeter-wave (mmWave), the signal sent by the base station is seriously attenuated when it reaches the indoors. Recent studies have proposed a glass-based metasurface that can enhance mmWave indoor signals. The transparent reconfigurable intelligent surface (RIS) focuses on the mmWave signal to a specific location indoors. In this paper, a novel RIS-assisted mmWave indoor enhancement scheme is proposed, in which a transparent RIS is deployed on the glass to enhance mmWave indoor signals, and three assisted transmission scenarios, namely passive RIS (PRIS), active RIS (ARIS), and a novel hybrid RIS (HRIS) are proposed. This paper aims to maximize the signal-to-noise ratio (SNR) of the received signal for the three assisted transmission scenarios. The closed-form solution to the maximum SNR is presented in the PRIS and the ARIS-assisted transmission scenarios. Meanwhile, the closed-form solution to the maximum SNR for the HRIS-assisted transmission scenario is presented for given active unit cells. In addition, the performance of the proposed scheme is analyzed under three assisted transmission scenarios. The results indicate that under a specific RIS power budget, the ARIS-assisted transmission scenario achieves the highest data rate and energy efficiency. Also, it requires very few unit cells, thus dramatically reducing the size of the metasurface.
Open AccessActive RIS-Assisted mmWave Indoor Signal Enhancement Based on Transparent RIS
Due to the serious path loss of millimeter-wave (mmWave), the signal sent by the base station is seriously attenuated when it reaches the indoors. Recent studies have proposed a glass-based metasurface that can enhance mmWave indoor signals. The transparent reconfigurable intelligent surface (RIS) focuses on the mmWave signal to a specific location indoors. In this paper, a novel RIS-assisted mmWave indoor enhancement scheme is proposed, in which a transparent RIS is deployed on the glass to enhance mmWave indoor signals, and three assisted transmission scenarios, namely passive RIS (PRIS), active RIS (ARIS), and a novel hybrid RIS (HRIS) are proposed. This paper aims to maximize the signal-to-noise ratio (SNR) of the received signal for the three assisted transmission scenarios. The closed-form solution to the maximum SNR is presented in the PRIS and the ARIS-assisted transmission scenarios. Meanwhile, the closed-form solution to the maximum SNR for the HRIS-assisted transmission scenario is presented for given active unit cells. In addition, the performance of the proposed scheme is analyzed under three assisted transmission scenarios. The results indicate that under a specific RIS power budget, the ARIS-assisted transmission scenario achieves the highest data rate and energy efficiency. Also, it requires very few unit cells, thus dramatically reducing the size of the metasurface.
- Open Access
mmWave RIS Phase Shift Feedback Based on Knowledge Base Autoencoder Framework
In reconfigurable intelligent surface (RIS)-assisted wireless communication systems, adjusting the phase shift of RIS unit cells is crucial for improving communication performance. Due to massive RIS unit cells, the number of phase shift parameters fed back from the base station (BS) to the RIS is enormous, which occupies a large number of frequency resources. In this paper, we propose a feedback scheme for millimeter-wave RIS phase shift applying a knowledge base autoencoder framework, in which the learnable knowledge base is shared at the BS and the RIS. The encoder at the BS compresses the RIS phase shift matrix to multiple feature vectors. Then the knowledge base vectors index is obtained by calculating the similarity between feature vectors and knowledge base vectors and transmitted to the RIS. With utilizing the index at the RIS, the corresponding knowledge base vectors are extracted and used as the decoder's inputs to reconstruct the phase shift of the RIS. Simulation results show that the proposed scheme can significantly improve the accuracy of phase shift feedback and impressively reduce the amount of RIS phase shift feedback data. Moreover, the proposed scheme is easy to deploy in actual scenarios due to lower complexity and fewer parameters.
Open AccessmmWave RIS Phase Shift Feedback Based on Knowledge Base Autoencoder Framework
In reconfigurable intelligent surface (RIS)-assisted wireless communication systems, adjusting the phase shift of RIS unit cells is crucial for improving communication performance. Due to massive RIS unit cells, the number of phase shift parameters fed back from the base station (BS) to the RIS is enormous, which occupies a large number of frequency resources. In this paper, we propose a feedback scheme for millimeter-wave RIS phase shift applying a knowledge base autoencoder framework, in which the learnable knowledge base is shared at the BS and the RIS. The encoder at the BS compresses the RIS phase shift matrix to multiple feature vectors. Then the knowledge base vectors index is obtained by calculating the similarity between feature vectors and knowledge base vectors and transmitted to the RIS. With utilizing the index at the RIS, the corresponding knowledge base vectors are extracted and used as the decoder's inputs to reconstruct the phase shift of the RIS. Simulation results show that the proposed scheme can significantly improve the accuracy of phase shift feedback and impressively reduce the amount of RIS phase shift feedback data. Moreover, the proposed scheme is easy to deploy in actual scenarios due to lower complexity and fewer parameters.
- 10 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Wireless Communications Letters
- Vol. 12 (7) , 1179-1183
mmWave RIS-Assisted SIMO Channel Estimation Based on Global Attention Residual Network
Reconfigurable intelligent surface (RIS) is promising for enhancing millimeter wave signal coverage. However, traditional channel estimation (CE) methods have high complexity and pilot overhead due to RIS’s passive nature and a large number of unit cells. Recently, deep learning (DL) has shown the potential in improving communication system performance. This paper proposes a DL-based scheme for estimating the cascaded channel in a RIS-assisted communication system. The proposed scheme utilizes the global attention residual network, which considers multi-channel information fusion on the channel feature matrices to improve CE matrix accuracy. Simulation results demonstrate that the proposed scheme significantly improves CE accuracy and has good generalization performance.
- 10 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Wireless Communications Letters
- Vol. 12 (7) , 1179-1183
mmWave RIS-Assisted SIMO Channel Estimation Based on Global Attention Residual Network
Reconfigurable intelligent surface (RIS) is promising for enhancing millimeter wave signal coverage. However, traditional channel estimation (CE) methods have high complexity and pilot overhead due to RIS’s passive nature and a large number of unit cells. Recently, deep learning (DL) has shown the potential in improving communication system performance. This paper proposes a DL-based scheme for estimating the cascaded channel in a RIS-assisted communication system. The proposed scheme utilizes the global attention residual network, which considers multi-channel information fusion on the channel feature matrices to improve CE matrix accuracy. Simulation results demonstrate that the proposed scheme significantly improves CE accuracy and has good generalization performance.