Jinghao Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jinghao Li has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Wanchen Yang
Nanjing University of Aeronautics and Astronautics
6 shared publications - Wenquan Che
South China University of Technology
6 shared publications - Quan Xue
South China University of Technology
4 shared publications - Shilong Pan
Nanjing University of Aeronautics and Astronautics
2 shared publications - Chujun Liang
College of Electronic and Information Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing, China
1 shared publication - Dongxu Chen
College of Information Science and Engineering, Hohai University, Nanjing, China
1 shared publication
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (10) , 9498-9509
Millimeter-Wave Broadband Wide-Scanning Phased Array With Stable Scanning Gain Based on Broadband Planar Decoupling Path
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (10) , 9498-9509
Millimeter-Wave Broadband Wide-Scanning Phased Array With Stable Scanning Gain Based on Broadband Planar Decoupling Path
- 6 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (11) , 8536-8549
K-/Ka-Band Shared-Aperture Dual-CP Phased Array Based on Amplitude-Regulated Sequential Feeding for Satellite Communication
SSatellite communication (SATCOM) is essential for 6G networks, supporting Space-air-ground Integrated Network (SAGIN) and global coverage especially in remote and mobile scenarios. This work proposes a novel dual-band dual-circularly polarized (CP) shared-aperture phased array using amplitude-regulated sequential feeding (ARSF) for simultaneous K-band (downlink) and Ka-band (uplink) CP operation in SATCOM. Theoretical analysis demonstrate amplitude regulation between multiple linearly polarized (LP) components enables effective CP synthesis despite significant phase gradient φ deviates from 90°, allowing for broader CP bandwidth (over 100%) or dual-band CP operation without complex phase-shift networks. The dual-band (K-/Ka-band) and higher-band (Ka-band) elements employ metasurface (MS) as radiator with identical lamination stack-up. Subsequently, the proposed K-/Ka-band shared-aperture array is constructed by 4 × 4 dual-band elements and 8 higher-band elements to ensure dual-band wide-angle scanning capacity. Both simulated and measured results confirm the dual-band operation. The array achieves scanning angles up to ±55° in K-band and ±60° in Ka-band, with axial ratio (AR) and gain drops ≤ 5 dB. Practical implementations could necessarily scale the array to achieve uniform scanning angle (e. g., ±60°) across bands while preserving transmit/receive (Tx/Rx) frequency division duplexing. This compact, lightweight, low-cost array offers high integration and wide-angle scanning capabilities, which is ideal for 6G unmanned aerial vehicles (UAV) applications.
- 6 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (11) , 8536-8549
K-/Ka-Band Shared-Aperture Dual-CP Phased Array Based on Amplitude-Regulated Sequential Feeding for Satellite Communication
SSatellite communication (SATCOM) is essential for 6G networks, supporting Space-air-ground Integrated Network (SAGIN) and global coverage especially in remote and mobile scenarios. This work proposes a novel dual-band dual-circularly polarized (CP) shared-aperture phased array using amplitude-regulated sequential feeding (ARSF) for simultaneous K-band (downlink) and Ka-band (uplink) CP operation in SATCOM. Theoretical analysis demonstrate amplitude regulation between multiple linearly polarized (LP) components enables effective CP synthesis despite significant phase gradient φ deviates from 90°, allowing for broader CP bandwidth (over 100%) or dual-band CP operation without complex phase-shift networks. The dual-band (K-/Ka-band) and higher-band (Ka-band) elements employ metasurface (MS) as radiator with identical lamination stack-up. Subsequently, the proposed K-/Ka-band shared-aperture array is constructed by 4 × 4 dual-band elements and 8 higher-band elements to ensure dual-band wide-angle scanning capacity. Both simulated and measured results confirm the dual-band operation. The array achieves scanning angles up to ±55° in K-band and ±60° in Ka-band, with axial ratio (AR) and gain drops ≤ 5 dB. Practical implementations could necessarily scale the array to achieve uniform scanning angle (e. g., ±60°) across bands while preserving transmit/receive (Tx/Rx) frequency division duplexing. This compact, lightweight, low-cost array offers high integration and wide-angle scanning capabilities, which is ideal for 6G unmanned aerial vehicles (UAV) applications.
- 7 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 74 (7) , 10344-10355
Millimeter-Wave Dual-Circularly Polarized Wide-Angle Scanning Antenna Array for Vehicular Communication Systems
This manuscript presents a millimeter-wave wideband and wide-angle scanning dual-circularly polarized (CP) antenna array based on traveling-wave sequential feeding metasurface (TSF-MS) for vehicular communication systems. The antenna element consists of a dual-layer rectangle metasurface structures fed by a simple two-port traveling-wave sequential stripline through four non-uniform crossed slots. Each crossed slot will be excited twice by the ring strip line, which means the slots are reused. By adjusting the length and width of the crossed slots and strip line, two orthogonal electric fields with equal amplitudes and 90$^{\circ }$ phase difference can be achieved, thereby realizing good right- and left-handed circular polarizations (RHCP, LHCP). The antenna element can achieve a wide impedance bandwidth of 25.8% and axial ratio (AR) bandwidth of 31%, with a compact size of 0.38 $\lambda _{\mathrm{{mid}}}$, which is far smaller than the other reported CP antenna. Then, based on the newly designed dual-CP antenna element, a 4×4 array is constructed by 2×2 sequentially rotated subarrays. This layout can improve the scanning performance, suppress the cross polarization, and realize modular wiring to simplify the feed network. Benefited from the layout, the array can achieve a wide scanning angle of $\pm$60 over the whole bandwidth with the gain variation and AR less than 3 dB. For demonstration, one prototype is fabricated and the measured results show a good agreement with the simulated results. The dual-CP wide-angle scanning phased array can fully meet the communication needs of vehicular communication systems, indicating a good application prospect.
- 7 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 74 (7) , 10344-10355
Millimeter-Wave Dual-Circularly Polarized Wide-Angle Scanning Antenna Array for Vehicular Communication Systems
This manuscript presents a millimeter-wave wideband and wide-angle scanning dual-circularly polarized (CP) antenna array based on traveling-wave sequential feeding metasurface (TSF-MS) for vehicular communication systems. The antenna element consists of a dual-layer rectangle metasurface structures fed by a simple two-port traveling-wave sequential stripline through four non-uniform crossed slots. Each crossed slot will be excited twice by the ring strip line, which means the slots are reused. By adjusting the length and width of the crossed slots and strip line, two orthogonal electric fields with equal amplitudes and 90$^{\circ }$ phase difference can be achieved, thereby realizing good right- and left-handed circular polarizations (RHCP, LHCP). The antenna element can achieve a wide impedance bandwidth of 25.8% and axial ratio (AR) bandwidth of 31%, with a compact size of 0.38 $\lambda _{\mathrm{{mid}}}$, which is far smaller than the other reported CP antenna. Then, based on the newly designed dual-CP antenna element, a 4×4 array is constructed by 2×2 sequentially rotated subarrays. This layout can improve the scanning performance, suppress the cross polarization, and realize modular wiring to simplify the feed network. Benefited from the layout, the array can achieve a wide scanning angle of $\pm$60 over the whole bandwidth with the gain variation and AR less than 3 dB. For demonstration, one prototype is fabricated and the measured results show a good agreement with the simulated results. The dual-CP wide-angle scanning phased array can fully meet the communication needs of vehicular communication systems, indicating a good application prospect.
- 14 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (5) , 1193-1197
66–76 GHz High-Isolation 1-D Wide-Angle Scanning Phased Array Antenna With Bent-Wall Structures
In this manuscript, a millimeter-wave wide-angle scanning phased array antenna based on low-temperature co-fired ceramics (LTCC) is proposed. Firstly, metal grounded vias and metal plate are introduced around the patch antenna to form a bent wall, which can broaden the E-plane beamwidth from 100° to 118° at 66-76 GHz. Based on the wide-beam element, a 4×4 array is constructed with a spacing of only 0.38λ0, and a Π-shaped decoupling structure is introduced between adjacent elements to construct a planar coupling cancellation path (PCCP) with equal magnitude and opposite phase, which can increase the isolation from 15 dB to 20 dB. In addition, two rows of dummy elements (DE) are loaded along the E-plane on both sides of the array to improve the maximum scanning angle to ±71°, with the gain attenuation within 2 dB. The antenna prototypes are fabricated and the measured and simulated results are highly consistent, indicating the proposed phased array antenna is a favorable candidate for 6G applications.
- 14 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (5) , 1193-1197
66–76 GHz High-Isolation 1-D Wide-Angle Scanning Phased Array Antenna With Bent-Wall Structures
In this manuscript, a millimeter-wave wide-angle scanning phased array antenna based on low-temperature co-fired ceramics (LTCC) is proposed. Firstly, metal grounded vias and metal plate are introduced around the patch antenna to form a bent wall, which can broaden the E-plane beamwidth from 100° to 118° at 66-76 GHz. Based on the wide-beam element, a 4×4 array is constructed with a spacing of only 0.38λ0, and a Π-shaped decoupling structure is introduced between adjacent elements to construct a planar coupling cancellation path (PCCP) with equal magnitude and opposite phase, which can increase the isolation from 15 dB to 20 dB. In addition, two rows of dummy elements (DE) are loaded along the E-plane on both sides of the array to improve the maximum scanning angle to ±71°, with the gain attenuation within 2 dB. The antenna prototypes are fabricated and the measured and simulated results are highly consistent, indicating the proposed phased array antenna is a favorable candidate for 6G applications.
- Open Access
- 23 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 6 (1) , 6-24
Advanced Metasurface-Based Antennas: A Review
As one kind of two-dimensional metamaterials, metasurface structures are widely applied in antennas due to the special abilities of manipulating the amplitude, phase, polarization states and the propagation modes of electromagnetic wave. This article briefly presents a series of combinations of metasurface and antennas from the perspective of design methods and innovative features, which are divided into three sections: performance improvement, function manipulation and other applications. In the section of performance improvement, three typical applications of metasurface are presented, including using non-periodic metasurfaces to raise aperture efficiency, introducing multi-mode resonance metasurfaces to expand bandwidth, and introducing capacitive loading metasurfaces for miniaturization. As for function manipulation, due to the high design freedom of metasurface, multi-polarization reconfigurability can be achieved by changing the surface impedance distribution. Moreover, it can be used as radiators and excited by traveling wave to achieve beam steering or combined with phase change materials to realize frequency reconfiguration. The last part is about the further applications of metasurface, including multi-folding reflectarray/ transmitarray, wide-angle scanning phased array antenna, and filtering antenna. In conclusion, the researches of metasurface have overcome the shortcomings of conventional antennas and proposed some good solutions to realize innovative antennas.
- 23 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Antennas and Propagation
- Vol. 6 (1) , 6-24
Open AccessAdvanced Metasurface-Based Antennas: A Review
As one kind of two-dimensional metamaterials, metasurface structures are widely applied in antennas due to the special abilities of manipulating the amplitude, phase, polarization states and the propagation modes of electromagnetic wave. This article briefly presents a series of combinations of metasurface and antennas from the perspective of design methods and innovative features, which are divided into three sections: performance improvement, function manipulation and other applications. In the section of performance improvement, three typical applications of metasurface are presented, including using non-periodic metasurfaces to raise aperture efficiency, introducing multi-mode resonance metasurfaces to expand bandwidth, and introducing capacitive loading metasurfaces for miniaturization. As for function manipulation, due to the high design freedom of metasurface, multi-polarization reconfigurability can be achieved by changing the surface impedance distribution. Moreover, it can be used as radiators and excited by traveling wave to achieve beam steering or combined with phase change materials to realize frequency reconfiguration. The last part is about the further applications of metasurface, including multi-folding reflectarray/ transmitarray, wide-angle scanning phased array antenna, and filtering antenna. In conclusion, the researches of metasurface have overcome the shortcomings of conventional antennas and proposed some good solutions to realize innovative antennas.
- 8 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (4) , 3134-3145
Reconfigurable Millimeter-Wave Tri-Band Antenna Based on VO2-Films-Embedded Co-Aperture Metasurface Structures
A novel reconfigurable millimeter-wave tri-band antenna using co-aperture metasurface structures embedded with electrically controlling vanadium dioxide (VO 2 ) films is proposed. A co-aperture metasurface structure is designed by loading a large square ring surrounded with eight small square patches in the same aperture. By embedding the VO 2 film into the large ring, two lower frequencies of 22 and 28 GHz can be excited and switched when the film operates in metallic and insulating states respectively. Meanwhile, an extra higher-mode resonance at 40 GHz is produced by the small patches. Benefit from the reasonable co-aperture layout, the three frequency bands exhibit good independent tunability. Furthermore, the tri-band metasurface structure is used as radiation element to construct a reconfigurable antenna. To realize good feeding coupling at three bands with large frequency ratio for the antenna, a new kind of combined slot is proposed and etched on the transverse surface of the feeding waveguide. The combined slot contains a loop slot, a dumbbell-shaped slot and two U-shaped slots, corresponding to low, medium and high frequencies respectively. In addition, a simple coplanar DC bias circuit with little effect on radiation is designed. As results, when the VO 2 film is in insulating state, the antenna can simultaneously cover two bands of 27.7-29.8 GHz and 38.8-40 GHz with the maximum gain of about 8.7 dBi and 9.5 dBi respectively; when the film is activated to metallic state, it can also work in two bands of 21.1-21.6 GHz and 38.6-40 GHz with the maximum gain of about 7.2 dBi and 9.3 dBi. Compared with other reported VO 2 -based antennas, the proposed antenna can work in three different bands with adjustable frequency ratio and superior radiation performance.
- 8 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 71 (4) , 3134-3145
Reconfigurable Millimeter-Wave Tri-Band Antenna Based on VO2-Films-Embedded Co-Aperture Metasurface Structures
A novel reconfigurable millimeter-wave tri-band antenna using co-aperture metasurface structures embedded with electrically controlling vanadium dioxide (VO 2 ) films is proposed. A co-aperture metasurface structure is designed by loading a large square ring surrounded with eight small square patches in the same aperture. By embedding the VO 2 film into the large ring, two lower frequencies of 22 and 28 GHz can be excited and switched when the film operates in metallic and insulating states respectively. Meanwhile, an extra higher-mode resonance at 40 GHz is produced by the small patches. Benefit from the reasonable co-aperture layout, the three frequency bands exhibit good independent tunability. Furthermore, the tri-band metasurface structure is used as radiation element to construct a reconfigurable antenna. To realize good feeding coupling at three bands with large frequency ratio for the antenna, a new kind of combined slot is proposed and etched on the transverse surface of the feeding waveguide. The combined slot contains a loop slot, a dumbbell-shaped slot and two U-shaped slots, corresponding to low, medium and high frequencies respectively. In addition, a simple coplanar DC bias circuit with little effect on radiation is designed. As results, when the VO 2 film is in insulating state, the antenna can simultaneously cover two bands of 27.7-29.8 GHz and 38.8-40 GHz with the maximum gain of about 8.7 dBi and 9.5 dBi respectively; when the film is activated to metallic state, it can also work in two bands of 21.1-21.6 GHz and 38.6-40 GHz with the maximum gain of about 7.2 dBi and 9.3 dBi. Compared with other reported VO 2 -based antennas, the proposed antenna can work in three different bands with adjustable frequency ratio and superior radiation performance.