Pengcheng Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Pengcheng Yang has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
Xindong Zhu
Xi'an Jiaotong University
6 shared publicationsMasaharu Komori
Kyoto Univ. (Japan)
3 shared publicationsSuping Fang
Xi'an Jiaotong Univ. (China)
3 shared publicationsAizoh Kubo
Kyoto University, Department of Precision Engineering, Faculty of Engineering, Yoshida Honmachi, Sakyo-ku, Kyoto 606-8501, Japan
2 shared publicationsCui Jia-Bao
2 shared publicationsLiping Lian
2 shared publications
Latest Publications
- 1 July 2026
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 65 (07) , 1-20
Multiconstrained optical path optimization of interferometric measurement system based on fringe-density characteristics
When measuring the profile deviation of helical tooth flanks using laser interferometry, a helical surface inevitably generates dense interference fringes that cause fringe adhesion and blurring. This compromises the quality of the interferogram and increases the difficulty of the subsequent image processing. To address this challenge, a multiconstrained optical path optimization method is proposed. First, multiple evaluation metrics were introduced to construct a comprehensive quality evaluation matrix. Next, by establishing a theoretical model correlating the rate of phase difference variation with relevant optical path parameters, it is clarified that mismatches between the abrupt curvature changes of the measured surface and optical path parameters, such as the incidence angle, convergence angle, and imaging object distance, are the key causes of the excessive interference fringe density. Based on this analysis, a multiconstrained optimization method was developed to achieve a uniform fringe distribution. Simulations and two groups of experimental results showed that the proposed method reduced the number of phase residue points by 76% to 83%, decreases the RMS phase gradient by 30% to 34%, and improves the second-order gradient variance by 46% to 54%. These results demonstrate the effectiveness of the method in modulating fringe density and substantially improving the quality of interferograms.
- 1 July 2026
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 65 (07) , 1-20
Multiconstrained optical path optimization of interferometric measurement system based on fringe-density characteristics
When measuring the profile deviation of helical tooth flanks using laser interferometry, a helical surface inevitably generates dense interference fringes that cause fringe adhesion and blurring. This compromises the quality of the interferogram and increases the difficulty of the subsequent image processing. To address this challenge, a multiconstrained optical path optimization method is proposed. First, multiple evaluation metrics were introduced to construct a comprehensive quality evaluation matrix. Next, by establishing a theoretical model correlating the rate of phase difference variation with relevant optical path parameters, it is clarified that mismatches between the abrupt curvature changes of the measured surface and optical path parameters, such as the incidence angle, convergence angle, and imaging object distance, are the key causes of the excessive interference fringe density. Based on this analysis, a multiconstrained optimization method was developed to achieve a uniform fringe distribution. Simulations and two groups of experimental results showed that the proposed method reduced the number of phase residue points by 76% to 83%, decreases the RMS phase gradient by 30% to 34%, and improves the second-order gradient variance by 46% to 54%. These results demonstrate the effectiveness of the method in modulating fringe density and substantially improving the quality of interferograms.
- 10 April 2024
- Published by Elsevier in Optics Communications
- Vol. 563
Incident angle optimization with multiple conflicting objectives based on BP-MOPSO in oblique laser interferometry
- 10 April 2024
- Published by Elsevier in Optics Communications
- Vol. 563
Incident angle optimization with multiple conflicting objectives based on BP-MOPSO in oblique laser interferometry
- 1 January 2024
- Published by Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences in Chinese Optics
- Vol. 17 (3) , 572-579
A point cloud classification downsampling and registration method for cultural relics based on curvature features
The predecessor of China Optics was China Optics and Applied Optics Digest, which was founded in 1985. At that time, it was the only retrieval journal in the field of optics in China. At the end of 2008, China Optics and Applied Optics Digest was renamed 《中国光学》的前身是1985年创办的《中国光学与应用光学文摘》,当时是国内光学领域唯一的检索刊物。2008年底《中国光学与应用光学文摘》转型更名为《中国光学与应用光学》期刊,刊载内容突破了文摘的限制,正式成为学术刊物。
- 1 January 2024
- Published by Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences in Chinese Optics
- Vol. 17 (3) , 572-579
A point cloud classification downsampling and registration method for cultural relics based on curvature features
The predecessor of China Optics was China Optics and Applied Optics Digest, which was founded in 1985. At that time, it was the only retrieval journal in the field of optics in China. At the end of 2008, China Optics and Applied Optics Digest was renamed 《中国光学》的前身是1985年创办的《中国光学与应用光学文摘》,当时是国内光学领域唯一的检索刊物。2008年底《中国光学与应用光学文摘》转型更名为《中国光学与应用光学》期刊,刊载内容突破了文摘的限制,正式成为学术刊物。
- 11 September 2023
- Published by Elsevier in Optics & Laser Technology
- Vol. 169
Design optical surface as the measurement datum in measuring gear tooth flank by symmetrical laser interferometer
- 11 September 2023
- Published by Elsevier in Optics & Laser Technology
- Vol. 169
Design optical surface as the measurement datum in measuring gear tooth flank by symmetrical laser interferometer
- 13 April 2023
- Published by Elsevier in Optics Communications
- Vol. 540
Valid measurement region segmentation method for the interferogram based on local fringe distribution features
- 13 April 2023
- Published by Elsevier in Optics Communications
- Vol. 540
Valid measurement region segmentation method for the interferogram based on local fringe distribution features
- 1 January 2023
- Published by Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences in Chinese Optics
- Vol. 16 (3) , 654-662
Aligning method for point cloud prism boundaries of cultural relics based on normal vector and faceted index features
三维重建是文物信息保护常用的方法,主要通过点云配准技术重组文物空间点云信息,其配准精度对文物复现有重要影响。针对文物表面复杂点云纹理特征配准中存在精度低、鲁棒性差的问题,本文提出一种基于法向量夹角和面状指数特征的局域点云配准方法。首先,根据点云平面特性设定法向量夹角和协方差矩阵阈值,提取同时满足这两特征的点云特征点;其次,K近邻搜索提取点云局域特征点集,通过刚性变换将两组点云质心位置重合,进行粗配准;最终,在两点云粗配准位置基础上根据ICP迭代最近点进行精配准。通过与传统ICP进行对比,此方法点云配准误差下降3%,匹配耗时降低50%,有效地提高了配准的精度和效率,增强了点云配准的鲁棒性。
- 1 January 2023
- Published by Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences in Chinese Optics
- Vol. 16 (3) , 654-662
Aligning method for point cloud prism boundaries of cultural relics based on normal vector and faceted index features
三维重建是文物信息保护常用的方法,主要通过点云配准技术重组文物空间点云信息,其配准精度对文物复现有重要影响。针对文物表面复杂点云纹理特征配准中存在精度低、鲁棒性差的问题,本文提出一种基于法向量夹角和面状指数特征的局域点云配准方法。首先,根据点云平面特性设定法向量夹角和协方差矩阵阈值,提取同时满足这两特征的点云特征点;其次,K近邻搜索提取点云局域特征点集,通过刚性变换将两组点云质心位置重合,进行粗配准;最终,在两点云粗配准位置基础上根据ICP迭代最近点进行精配准。通过与传统ICP进行对比,此方法点云配准误差下降3%,匹配耗时降低50%,有效地提高了配准的精度和效率,增强了点云配准的鲁棒性。
- 1 December 2022
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 61 (12) , 124112-15
Optical path modulation of interference fringe density based on position errors analysis in oblique laser interferometry
When laser interferometry is applied to measure the form deviation of a helical tooth flank, dense interference fringes are almost inevitable because of the distorted shape of the helical tooth flank. The high-density fringe leads to poor processing accuracy of interferograms and is an important indicator of the interferogram quality. An optical path optimization method based on position errors analysis is proposed to modulate the fringe density. First, some factors that may affect fringe density in the optical system are modeled. Consequently, the incident angle of the measured light is proved to be the main factor affecting the fringe density and is the primary parameter that modulates the interference fringe density. Subsequently, an analytical model is established, and a fringe density modulation method based on the optimized incident angle is proposed for designing the optical path. Finally, simulated and actual experimental results are provided to verify the correctness of the analysis of the main factor affecting the fringe density and feasibility of the modulation method.
- 1 December 2022
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 61 (12) , 124112-15
Optical path modulation of interference fringe density based on position errors analysis in oblique laser interferometry
When laser interferometry is applied to measure the form deviation of a helical tooth flank, dense interference fringes are almost inevitable because of the distorted shape of the helical tooth flank. The high-density fringe leads to poor processing accuracy of interferograms and is an important indicator of the interferogram quality. An optical path optimization method based on position errors analysis is proposed to modulate the fringe density. First, some factors that may affect fringe density in the optical system are modeled. Consequently, the incident angle of the measured light is proved to be the main factor affecting the fringe density and is the primary parameter that modulates the interference fringe density. Subsequently, an analytical model is established, and a fringe density modulation method based on the optimized incident angle is proposed for designing the optical path. Finally, simulated and actual experimental results are provided to verify the correctness of the analysis of the main factor affecting the fringe density and feasibility of the modulation method.
- 12 September 2018
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 57 (09) , 094102-10
Construction of virtual measurement datum in measuring gear tooth flank by laser interferometry
A measurement datum is crucial in measuring a gear tooth flank by laser interferometry. Manufacturing a physical reference tooth flank as a measurement datum has many drawbacks: many different reference tooth flanks are needed with the changing of the measured gear’s parameters; the reference tooth flank’s manufacturing error lowers the measurement precision; the installation error between the measured and referenced tooth flank lowers the measurement precision also. The drawbacks restrain the practical use of measuring gear by laser interferometry. A construction method of a virtual measurement datum has been proposed to solve the problem. First, a virtual error-free model of the measured tooth flank is built according to its parameters and actual measurement position. Subsequently, the interferogram of the virtual tooth flank is simulated as a measurement datum through the ray tracing. To harvest the actual measurement position of the measured tooth flank, a compensation approach for optical system error and a tracing algorithm for actual installation position are developed. Experimental results prove that a virtual measurement datum can be constructed and used in measuring a gear tooth flank. Furthermore, this research verifies that ray tracing can be used to construct a virtual measurement datum in the relevant comparative measurements processes by laser interferometry.
- 12 September 2018
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 57 (09) , 094102-10
Construction of virtual measurement datum in measuring gear tooth flank by laser interferometry
A measurement datum is crucial in measuring a gear tooth flank by laser interferometry. Manufacturing a physical reference tooth flank as a measurement datum has many drawbacks: many different reference tooth flanks are needed with the changing of the measured gear’s parameters; the reference tooth flank’s manufacturing error lowers the measurement precision; the installation error between the measured and referenced tooth flank lowers the measurement precision also. The drawbacks restrain the practical use of measuring gear by laser interferometry. A construction method of a virtual measurement datum has been proposed to solve the problem. First, a virtual error-free model of the measured tooth flank is built according to its parameters and actual measurement position. Subsequently, the interferogram of the virtual tooth flank is simulated as a measurement datum through the ray tracing. To harvest the actual measurement position of the measured tooth flank, a compensation approach for optical system error and a tracing algorithm for actual installation position are developed. Experimental results prove that a virtual measurement datum can be constructed and used in measuring a gear tooth flank. Furthermore, this research verifies that ray tracing can be used to construct a virtual measurement datum in the relevant comparative measurements processes by laser interferometry.
- 1 August 2014
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 53 (8) , 084111
Analysis and compensation method for installation error in measuring gear tooth flank with laser interferometry
The installation position errors of a measured gear are unavoidable when measuring gear tooth flank form deviation with laser interferometry, causing mistakes when using the simulated phase difference as a measurement reference to calculate the form deviation. In order to avoid manufacturing many standard gears as measurement references, a compensation method for the installation errors of the measured gear has been developed. In this process, the actual installation position of the measured gear can be traced by modifying the theoretical position parameters using the ray-tracing method. Experimental results show that this method is feasible. Thus, the simulated phase difference that compensate for installation errors can be utilized as a measurement reference in calculating the form deviation of the measured gear.
- 1 August 2014
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 53 (8) , 084111
Analysis and compensation method for installation error in measuring gear tooth flank with laser interferometry
The installation position errors of a measured gear are unavoidable when measuring gear tooth flank form deviation with laser interferometry, causing mistakes when using the simulated phase difference as a measurement reference to calculate the form deviation. In order to avoid manufacturing many standard gears as measurement references, a compensation method for the installation errors of the measured gear has been developed. In this process, the actual installation position of the measured gear can be traced by modifying the theoretical position parameters using the ray-tracing method. Experimental results show that this method is feasible. Thus, the simulated phase difference that compensate for installation errors can be utilized as a measurement reference in calculating the form deviation of the measured gear.
- 1 September 2011
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 50 (9) , 095602-095602-6
Correction method for segmenting valid measuring region of interference fringe patterns
Segmenting the valid measuring region from an interferogram is an important step in the grazing incidence interferometry, which is related to the accuracy of the measurement result. For the spurious fringes which are generated by the diffuse reflection of the chamfering in the edge of the object surface, we propose a method-spin segment to correct the result of the image segment. First, a phase schematic diagram whose stripe feature is clearer than the original interference fringe patterns is generated. Next, the difference of the gray gradient between the fringe's local normal direction and local tangent direction is calculated to judge the valid measurement region. The principles of selecting some parameters are summarized and the calculation steps are shown. To examine the correction method, the results of an experimental application of spin segment are given to verify the feasibility and accuracy.
- 1 September 2011
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 50 (9) , 095602-095602-6
Correction method for segmenting valid measuring region of interference fringe patterns
Segmenting the valid measuring region from an interferogram is an important step in the grazing incidence interferometry, which is related to the accuracy of the measurement result. For the spurious fringes which are generated by the diffuse reflection of the chamfering in the edge of the object surface, we propose a method-spin segment to correct the result of the image segment. First, a phase schematic diagram whose stripe feature is clearer than the original interference fringe patterns is generated. Next, the difference of the gray gradient between the fringe's local normal direction and local tangent direction is calculated to judge the valid measurement region. The principles of selecting some parameters are summarized and the calculation steps are shown. To examine the correction method, the results of an experimental application of spin segment are given to verify the feasibility and accuracy.