Weitao Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Weitao Li has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Liping Wang
School of Mechanical and Electrical Engineering, University Of Electronic Science And Technology Of China, Chengdu, China
2 shared publications- Guang Yu
State Key Laboratory of Tribology in Advanced Equipment, Tsinghua University, Beijing, China
1 shared publication Jie Zhang
School of Mechanical and Electrical Engineering, University Of Electronic Science And Technology Of China, Chengdu, China
1 shared publication- Liping Wang
Institute of Manufacturing Engineering, Department of Mechanical Engineering, Tsinghua University, Beijing, China
1 shared publication - Pengxuan Wei
School of Mechanical and Electrical Engineering, University of Electronic Science and Technology of China, Chengdu 611731, China
1 shared publication Yansong Zhou
School of Mechanical and Electrical Engineering, University Of Electronic Science And Technology Of China, Chengdu, China
1 shared publication
Latest Publications
- Open Access
A Deformation Prediction Method for Thin-Walled Workpiece Machining Based on the Voxel Octree Model
In flank milling of thin-walled workpieces, machining deformation is a key issue affecting workpiece accuracy and process stability. Although the traditional finite element method (FEM) offers high accuracy, its low computational efficiency makes it difficult to meet the requirements for rapid prediction in engineering practice. For this purpose, this paper proposes an efficient method for predicting workpiece deformation based on the voxel octree model. First, based on the analysis of the contact position between the cutting tool and the workpiece, the thin-walled workpiece is divided into six levels of voxel units, using a voxel octree model. Then, the stiffness matrix and update model of the voxel units are established. Finally, the deformation prediction is completed by calculating the micro-milling force and the voxel stiffness matrix. The experimental results show that the workpiece deformation predicted by the proposed method is highly consistent with the actual machining measurement. At the same time, compared with traditional FEM and voxel model methods, the calculation time is reduced by 90% and 13.2%, respectively. This method can provide rapid decision support for the optimization of thin-walled workpiece machining processes and effectively improve the efficiency of preliminary research in actual machining.
Open AccessA Deformation Prediction Method for Thin-Walled Workpiece Machining Based on the Voxel Octree Model
In flank milling of thin-walled workpieces, machining deformation is a key issue affecting workpiece accuracy and process stability. Although the traditional finite element method (FEM) offers high accuracy, its low computational efficiency makes it difficult to meet the requirements for rapid prediction in engineering practice. For this purpose, this paper proposes an efficient method for predicting workpiece deformation based on the voxel octree model. First, based on the analysis of the contact position between the cutting tool and the workpiece, the thin-walled workpiece is divided into six levels of voxel units, using a voxel octree model. Then, the stiffness matrix and update model of the voxel units are established. Finally, the deformation prediction is completed by calculating the micro-milling force and the voxel stiffness matrix. The experimental results show that the workpiece deformation predicted by the proposed method is highly consistent with the actual machining measurement. At the same time, compared with traditional FEM and voxel model methods, the calculation time is reduced by 90% and 13.2%, respectively. This method can provide rapid decision support for the optimization of thin-walled workpiece machining processes and effectively improve the efficiency of preliminary research in actual machining.
- 21 May 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 138 (7-8) , 3293-3313
Research on feedrate scheduling method for NURBS toolpath interpolation in high-speed CNC machining
- 21 May 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 138 (7-8) , 3293-3313
Research on feedrate scheduling method for NURBS toolpath interpolation in high-speed CNC machining
- 18 April 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 126 (9-10) , 4353-4367
Optimal deformation error compensation process in flank milling of thin-walled workpieces
- 18 April 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 126 (9-10) , 4353-4367
Optimal deformation error compensation process in flank milling of thin-walled workpieces