Martin Taraz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Martin Taraz has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Muhammad Abdullah
Hasso Plattner Institute, Potsdam, Germany
7 shared publications - Patrick Baudisch
Hasso Plattner Institute, Potsdam, Germany
7 shared publications - Lukas Rambold
Hasso Plattner Institute, Potsdam, Germany
6 shared publications - Robert Kovacs
Hasso Plattner Institute, Potsdam, Germany
6 shared publications - Shohei Katakura
Hasso Plattner Institute, Potsdam, Germany
5 shared publications - Conrad Lempert
Hasso Plattner Institute, Potsdam, Germany
4 shared publications
Latest Publications
- Open Access
- 2 November 2026
- Published by Association for Computing Machinery (ACM)
- p. 1-12
PÅCKER: Making Large Laser-Cut Objects Easy-to-Store and Transport
- 2 November 2026
- Published by Association for Computing Machinery (ACM)
- p. 1-12
Open AccessPÅCKER: Making Large Laser-Cut Objects Easy-to-Store and Transport
- Open Access
- 2 November 2026
- Published by Association for Computing Machinery (ACM)
- p. 1-13
The Future of 5DOF Laser Cutting Is Personal
- 2 November 2026
- Published by Association for Computing Machinery (ACM)
- p. 1-13
Open AccessThe Future of 5DOF Laser Cutting Is Personal
- Open Access
- 27 September 2025
- Published by Association for Computing Machinery (ACM)
- p. 1-14
Mallet-Based Assembly: Enabling Load-Bearing Laser-Cut Models
- 27 September 2025
- Published by Association for Computing Machinery (ACM)
- p. 1-14
Open AccessMallet-Based Assembly: Enabling Load-Bearing Laser-Cut Models
- Open Access
- 7 July 2024
- Published by Association for Computing Machinery (ACM)
- p. 1-3
Demonstrating AirTied: Automatic Personal Fabrication of Truss Structures
We demonstrate AirTied [Rambold et al., 2023], a device that fabricates truss structures in a fully automatic fashion. AirTied achieves this by unrolling a 20cm-wide inflatable plastic tube and tying nodes into it. AirTied creates nodes by holding onto a segment of tube, stacking additional tube segments on top of it, tying them up, and releasing the result. The resulting structures are material-efficient and light as well as sturdy, as we demonstrate by creating a 6m-tower. Unlike the prior art, AirTied requires no scaffolding and no building blocks, bringing automated truss construction into the reach of personal fabrication.
- 7 July 2024
- Published by Association for Computing Machinery (ACM)
- p. 1-3
Open AccessDemonstrating AirTied: Automatic Personal Fabrication of Truss Structures
We demonstrate AirTied [Rambold et al., 2023], a device that fabricates truss structures in a fully automatic fashion. AirTied achieves this by unrolling a 20cm-wide inflatable plastic tube and tying nodes into it. AirTied creates nodes by holding onto a segment of tube, stacking additional tube segments on top of it, tying them up, and releasing the result. The resulting structures are material-efficient and light as well as sturdy, as we demonstrate by creating a 6m-tower. Unlike the prior art, AirTied requires no scaffolding and no building blocks, bringing automated truss construction into the reach of personal fabrication.
- Open Access
- 29 October 2023
- Published by Association for Computing Machinery (ACM)
- p. 1-10
AirTied: Automatic Personal Fabrication of Truss Structures
- 29 October 2023
- Published by Association for Computing Machinery (ACM)
- p. 1-10
Open AccessAirTied: Automatic Personal Fabrication of Truss Structures
- Open Access
- 19 April 2023
- Published by Association for Computing Machinery (ACM)
- p. 1-13
Kerfmeter: Automatic Kerf Calibration for Laser Cutting
We present Kerfmeter, a hardware + software device that automatically determines how much material the laser cutter burns off, also known as kerf. Its knowledge about kerf allows Kerfmeter to make the joints of laser cut 3D models fit together with just the right tension, i.e., loose enough to allow for comfortable assembly, yet tight enough to hold parts together without glue—all this without user interaction. Kerfmeter attaches to the head of a laser cutter and works as follows: when users send a model to the laser cutter, Kerfmeter intercepts the job, injects a brief calibration routine that determines kerf, dilates the cutting plan according to this kerf, and then proceeds to fabricate the cutting plan. During the calibration routine, Kerfmeter cuts a 2cm Archimedean spiral and uses a motor to rotate it in place until it jams against the surrounding material; the angle at which the spiral jams allows Kerfmeter to infer kerf. The calibration process takes about 20s, which is >10x faster than traditional, manual kerf calibration, while also eliminating the need for expertise. In our technical evaluation, Kerfmeter produced functioning press fit joints reliably at a precision comparable to traditional manual kerf strips. Kerfmeter makes it easy to sample repeatedly; we demonstrate how this allows boosting precision past any traditional kerf strip.
- 19 April 2023
- Published by Association for Computing Machinery (ACM)
- p. 1-13
Open AccessKerfmeter: Automatic Kerf Calibration for Laser Cutting
We present Kerfmeter, a hardware + software device that automatically determines how much material the laser cutter burns off, also known as kerf. Its knowledge about kerf allows Kerfmeter to make the joints of laser cut 3D models fit together with just the right tension, i.e., loose enough to allow for comfortable assembly, yet tight enough to hold parts together without glue—all this without user interaction. Kerfmeter attaches to the head of a laser cutter and works as follows: when users send a model to the laser cutter, Kerfmeter intercepts the job, injects a brief calibration routine that determines kerf, dilates the cutting plan according to this kerf, and then proceeds to fabricate the cutting plan. During the calibration routine, Kerfmeter cuts a 2cm Archimedean spiral and uses a motor to rotate it in place until it jams against the surrounding material; the angle at which the spiral jams allows Kerfmeter to infer kerf. The calibration process takes about 20s, which is >10x faster than traditional, manual kerf calibration, while also eliminating the need for expertise. In our technical evaluation, Kerfmeter produced functioning press fit joints reliably at a precision comparable to traditional manual kerf strips. Kerfmeter makes it easy to sample repeatedly; we demonstrate how this allows boosting precision past any traditional kerf strip.
- Open Access
- 19 April 2023
- Published by Association for Computing Machinery (ACM)
- p. 1-5
Pushing Fabrication Research past the Makers
In this demonstration, we show a selection of twelve past CHI and UIST projects by our lab, which taken together aim at helping the field of digital fabrication using laser cutters transition past makers—and towards true non-experts, which we refer to as “consumers”. Our software systems provide such non-experts with domain knowledge (Kyub and fastForce), hardware and machine knowledge (Constructable, LaserOrigami, LaserStacker, springFit, kerf-canceling mechanisms, Assembler3 and autoAssembler), assembling laser-cut objects (FoolProofJoint, Roadkill, HingeCore) and demonstrate our contributions in solving these challenges over the course of twelve projects during the last few years.
- 19 April 2023
- Published by Association for Computing Machinery (ACM)
- p. 1-5
Open AccessPushing Fabrication Research past the Makers
In this demonstration, we show a selection of twelve past CHI and UIST projects by our lab, which taken together aim at helping the field of digital fabrication using laser cutters transition past makers—and towards true non-experts, which we refer to as “consumers”. Our software systems provide such non-experts with domain knowledge (Kyub and fastForce), hardware and machine knowledge (Constructable, LaserOrigami, LaserStacker, springFit, kerf-canceling mechanisms, Assembler3 and autoAssembler), assembling laser-cut objects (FoolProofJoint, Roadkill, HingeCore) and demonstrate our contributions in solving these challenges over the course of twelve projects during the last few years.