Andre Jöckel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Andre Jöckel has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
J. Baumgartner
Fraunhofer Institute for Structural Durability and System Reliability LBF, Darmstadt, Germany
3 shared publicationsH. Heinemann
Surface Engineering Institute (IOT), RWTH Aachen University, Aachen, Germany
2 shared publicationsJ. Bültena
Institute of Materials Engineering (LWT), Dortmund University, Dortmund, Germany
2 shared publicationsK. Bobzin
Surface Engineering Institute (IOT), RWTH Aachen University, Aachen, Germany
2 shared publicationsM. Erck
Surface Engineering Institute (IOT), RWTH Aachen University, Aachen, Germany
2 shared publicationsW. Tillmann
Institute of Materials Engineering (LWT), Dortmund University, Dortmund, Germany
2 shared publications
Latest Publications
- Open Access
- 23 April 2025
- Published by Springer Nature in Welding in the World
- Vol. 69 (8) , 2293-2310
Fatigue strength assessment of welded steel fasteners using structural stress concept with consideration of the mounting pre-load
The document presents a comprehensive investigation into the fatigue strength assessment of welded fasteners, specifically bolts and nuts, used in various engineering applications. A fatigue strength assessment approach using a structural stress concept is established, accounting for the influence of mounting pre-loads and residual stresses from the welding process. With the developed approach, the fatigue strength of all investigated variants can be assessed with a scatter of 1:2. The experimental investigations showed that an early decrease in pre-load forces negatively affects the fatigue strength. While pre-load forces can enhance fatigue strength, a reduction in pre-load during service loading must be avoided to ensure a safe life.
- 23 April 2025
- Published by Springer Nature in Welding in the World
- Vol. 69 (8) , 2293-2310
Open AccessFatigue strength assessment of welded steel fasteners using structural stress concept with consideration of the mounting pre-load
The document presents a comprehensive investigation into the fatigue strength assessment of welded fasteners, specifically bolts and nuts, used in various engineering applications. A fatigue strength assessment approach using a structural stress concept is established, accounting for the influence of mounting pre-loads and residual stresses from the welding process. With the developed approach, the fatigue strength of all investigated variants can be assessed with a scatter of 1:2. The experimental investigations showed that an early decrease in pre-load forces negatively affects the fatigue strength. While pre-load forces can enhance fatigue strength, a reduction in pre-load during service loading must be avoided to ensure a safe life.
- Open Access
- 29 April 2023
- Published by Springer Nature in Welding in the World
- Vol. 67 (7) , 1833-1852
Local approaches for the fatigue strength assessment of brazed joints made of X5CrNi18-10 and Cu 110 considering brazed seam quality and failure behavior
In the case of cyclically loaded brazed joints, especially in safety-relevant components like common rail systems for common rail direct fuel injection, it is necessary to reliably estimate the fatigue strength, considering the influence of different manufacturing processes, manufacturing parameters, and failure behavior. In this paper, induction-brazed, vacuum-brazed, and continuous furnace-brazed joints are used to develop a reliable approach to assess the fatigue life. Therefore, the specimens were characterized and tested under load control using constant amplitudes. It is found that the local brazing geometry in conjunction with the surface condition, which differs by different topography values and by the position and number of initial defects, have the most influence on the failure behavior and consequently on the fatigue strength. Irrespective of this, however, it is shown that the fatigue strength can be estimated sufficiently well even with a simplified finite element modeling that uses idealized fillet radii and by taking support effects into account.
- 29 April 2023
- Published by Springer Nature in Welding in the World
- Vol. 67 (7) , 1833-1852
Open AccessLocal approaches for the fatigue strength assessment of brazed joints made of X5CrNi18-10 and Cu 110 considering brazed seam quality and failure behavior
In the case of cyclically loaded brazed joints, especially in safety-relevant components like common rail systems for common rail direct fuel injection, it is necessary to reliably estimate the fatigue strength, considering the influence of different manufacturing processes, manufacturing parameters, and failure behavior. In this paper, induction-brazed, vacuum-brazed, and continuous furnace-brazed joints are used to develop a reliable approach to assess the fatigue life. Therefore, the specimens were characterized and tested under load control using constant amplitudes. It is found that the local brazing geometry in conjunction with the surface condition, which differs by different topography values and by the position and number of initial defects, have the most influence on the failure behavior and consequently on the fatigue strength. Irrespective of this, however, it is shown that the fatigue strength can be estimated sufficiently well even with a simplified finite element modeling that uses idealized fillet radii and by taking support effects into account.
- Open Access
- 20 April 2023
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (15)
Fatigue Strength Assessment of Laser Beam Welded Joints Made of AA7075 and Magnetic Pulse Welded Joints Made of AA7075 and 3D‐Printed AlSi10Mg
The use of 7000 aluminum alloys has an important role in future lightweight structures in the field of mobility due to the low density and high strength. However, these alloys can only be fusion welded to a limited extent because welding defects can rarely be prevented. For this reason, investigations are carried out to identify the most suitable welding parameters for two processes: laser beam and magnetic pulse welding. Herein, laser beam welding is successfully used to manufacture a roll‐formed and longitudinally welded pipe made of AA7075 and joined by magnetic pulse welding with a 3D‐printed lug‐tube made of AlSi10Mg. The fatigue strength of these pipe joints and of laser beam welded butt joint specimens is determined using load‐controlled fatigue tests. For the characterization of the specimens, cross sections are prepared and examined metallographically, which reflect the local weld seam geometry in the joining area. A fatigue assessment is made using linear‐elastic approaches. The reference radius concept is applied to map the influence of geometric notches on the fatigue strength, assuming linear‐elastic stress–strain behavior. It is shown that the recommended notch stress fatigue class FAT 178 (von Mises stress) can be applied for a safe and reliable fatigue assessment.
- 20 April 2023
- Published by Wiley in Advanced Engineering Materials
- Vol. 25 (15)
Open AccessFatigue Strength Assessment of Laser Beam Welded Joints Made of AA7075 and Magnetic Pulse Welded Joints Made of AA7075 and 3D‐Printed AlSi10Mg
The use of 7000 aluminum alloys has an important role in future lightweight structures in the field of mobility due to the low density and high strength. However, these alloys can only be fusion welded to a limited extent because welding defects can rarely be prevented. For this reason, investigations are carried out to identify the most suitable welding parameters for two processes: laser beam and magnetic pulse welding. Herein, laser beam welding is successfully used to manufacture a roll‐formed and longitudinally welded pipe made of AA7075 and joined by magnetic pulse welding with a 3D‐printed lug‐tube made of AlSi10Mg. The fatigue strength of these pipe joints and of laser beam welded butt joint specimens is determined using load‐controlled fatigue tests. For the characterization of the specimens, cross sections are prepared and examined metallographically, which reflect the local weld seam geometry in the joining area. A fatigue assessment is made using linear‐elastic approaches. The reference radius concept is applied to map the influence of geometric notches on the fatigue strength, assuming linear‐elastic stress–strain behavior. It is shown that the recommended notch stress fatigue class FAT 178 (von Mises stress) can be applied for a safe and reliable fatigue assessment.
- Open Access
- 4 May 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (10) , 1941-1955
Influence of brazing process and gap size on the fatigue strength of shear and peel specimen
Brazing is a joining technique used in many industries for components that consist of many individual parts. Many of these components are cyclically loaded during service. For this reason, reliable approaches to assess the service life must be developed. For this purpose, it is necessary to gain knowledge about factors influencing the fatigue strength and the damage behavior. In this paper induction, vacuum- and continuous furnace brazed shear and peel specimen with different brazing gap widths are analyzed. Therefore, the specimens were characterized, measuring the geometry of the specimens and surface condition of the brazing radii, and tested under load control using constant amplitudes. It is found that the manufacturing process and the parameters used have a significant influence on the mechanical properties of the brazing material, the surface condition and the profile of the fillet radii. These properties have again an influence on the damage behavior and the fatigue strength. In particular crack-like defects of varying severity, which can extend deep into the brazing material, that are located in highly stressed areas of the fillet radii have a significant influence on the fatigue strength. It is also found that, regardless of the brazing process used, there is a tendency in the area of the brazing gap width for the number and size of defects to increase with increasing gap size, which can negatively affect fatigue strength depending on the damage behavior.
- 4 May 2022
- Published by Springer Nature in Welding in the World
- Vol. 66 (10) , 1941-1955
Open AccessInfluence of brazing process and gap size on the fatigue strength of shear and peel specimen
Brazing is a joining technique used in many industries for components that consist of many individual parts. Many of these components are cyclically loaded during service. For this reason, reliable approaches to assess the service life must be developed. For this purpose, it is necessary to gain knowledge about factors influencing the fatigue strength and the damage behavior. In this paper induction, vacuum- and continuous furnace brazed shear and peel specimen with different brazing gap widths are analyzed. Therefore, the specimens were characterized, measuring the geometry of the specimens and surface condition of the brazing radii, and tested under load control using constant amplitudes. It is found that the manufacturing process and the parameters used have a significant influence on the mechanical properties of the brazing material, the surface condition and the profile of the fillet radii. These properties have again an influence on the damage behavior and the fatigue strength. In particular crack-like defects of varying severity, which can extend deep into the brazing material, that are located in highly stressed areas of the fillet radii have a significant influence on the fatigue strength. It is also found that, regardless of the brazing process used, there is a tendency in the area of the brazing gap width for the number and size of defects to increase with increasing gap size, which can negatively affect fatigue strength depending on the damage behavior.