Maria F. Quintana
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Maria F. Quintana has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Francisco Pedrayes Gonzalez
Electrical Engineering Department, University of Oviedo, Gijn, Spain
4 shared publications - Gonzalo Alonso Orcajo
Electrical Engineering Department, University of Oviedo, Gijn, Spain
4 shared publications - Manes Fernandez Cabanas
Department Electrical Engineering, Universidad de Oviedo, 33204 Gijón, Spain
4 shared publications - Manuel García Melero
Department Electrical Engineering, Universidad de Oviedo, 33204 Gijón, Spain
3 shared publications - Andres Suarez-Gonzalez
Department Electrical Engineering, Universidad de Oviedo, 33204 Gijón, Spain
2 shared publications - Enrique Ernesto Valdés
Department Electrical Engineering, Universidad de Oviedo, 33204 Gijón, Spain
2 shared publications
Latest Publications
- Open Access
- 30 October 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (21) , 9939
Parameter Identification Method of a Double-Layer Supercapacitor by Using a Real Voltage Source
This article presents a new method for obtaining the electrical parameters of a supercapacitor (SC) modeled as a constant resistor in series with a capacitance that linearly varies with its internal voltage. This model provides sufficiently accurate results when the SC is subjected to rapid, short-term charging and discharging. In other methods described in the literature, the parameters are obtained by charging or discharging the SC with a constant current source of high value. In this study, the electrical parameters are calculated by charging or discharging the cell with a real constant voltage source (RVS) or by discharging the SC through a known and constant resistance. The calculation procedure requires the measurement of the cell voltage as a function of time. Two alternative estimation methods have been employed: the three-point method (3PM) and the least squares method (LSM). A series of experimental tests were conducted on cells from various manufacturers, with capacitances ranging from 150 F to 600 F. The laboratory measurements were then compared with the results obtained from theoretical models incorporating the parameters obtained for the variable capacity model. The results demonstrated that this straightforward procedure is capable of accurately characterizing the main branch of any SC.
- 30 October 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (21) , 9939
Open AccessParameter Identification Method of a Double-Layer Supercapacitor by Using a Real Voltage Source
This article presents a new method for obtaining the electrical parameters of a supercapacitor (SC) modeled as a constant resistor in series with a capacitance that linearly varies with its internal voltage. This model provides sufficiently accurate results when the SC is subjected to rapid, short-term charging and discharging. In other methods described in the literature, the parameters are obtained by charging or discharging the SC with a constant current source of high value. In this study, the electrical parameters are calculated by charging or discharging the cell with a real constant voltage source (RVS) or by discharging the SC through a known and constant resistance. The calculation procedure requires the measurement of the cell voltage as a function of time. Two alternative estimation methods have been employed: the three-point method (3PM) and the least squares method (LSM). A series of experimental tests were conducted on cells from various manufacturers, with capacitances ranging from 150 F to 600 F. The laboratory measurements were then compared with the results obtained from theoretical models incorporating the parameters obtained for the variable capacity model. The results demonstrated that this straightforward procedure is capable of accurately characterizing the main branch of any SC.
- Open Access
Thermal Analysis of a Fast Charger for Public Service Electric Vehicles Based on Supercapacitors
The aging of supercapacitors (SCs) depends on several factors, with temperature being one of the most important. When this is high, degradation of the electrolyte occurs. The impurities generated in its decomposition reduce the accessibility of the ions to the porous structure on the surface of the electrode, which reduces its capacity and increases its internal resistance. In some applications, such as electric vehicles whose storage system consists of SCs, fast chargers, which supply very high power, are used. This can lead to an increase in temperature and accelerated aging of the cells. Therefore, it is important to know how the temperature of the SCs evolves in these cases and what parameters it depends on, both electrical and thermal. In this contribution, mathematical formulae have been developed to determine the evolution of the temperature in time and its maximum value during the transient state. The formulae for obtaining the mean and maximum temperature, once the thermal steady state (TSS) has been reached, are also shown, considering that the charger cells are recharged from the grid at a constant current. Based on this formulation, the thermal analysis of a specific case is determined.
Open AccessThermal Analysis of a Fast Charger for Public Service Electric Vehicles Based on Supercapacitors
The aging of supercapacitors (SCs) depends on several factors, with temperature being one of the most important. When this is high, degradation of the electrolyte occurs. The impurities generated in its decomposition reduce the accessibility of the ions to the porous structure on the surface of the electrode, which reduces its capacity and increases its internal resistance. In some applications, such as electric vehicles whose storage system consists of SCs, fast chargers, which supply very high power, are used. This can lead to an increase in temperature and accelerated aging of the cells. Therefore, it is important to know how the temperature of the SCs evolves in these cases and what parameters it depends on, both electrical and thermal. In this contribution, mathematical formulae have been developed to determine the evolution of the temperature in time and its maximum value during the transient state. The formulae for obtaining the mean and maximum temperature, once the thermal steady state (TSS) has been reached, are also shown, considering that the charger cells are recharged from the grid at a constant current. Based on this formulation, the thermal analysis of a specific case is determined.
- Open Access
- 31 May 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (11) , 6714
Non-Linear Analytical Model for the Study of Double-Layer Supercapacitors in Different Industrial Uses
It is generally considered that the representation of a double layer supercapacitor (DLSC) cannot be performed with the usual capacitance and resistance series connected, as it induces a relatively high level of inaccuracy in the results. In multiple previous studies, more advanced models have been developed with very different approaches: models with distributed parameter circuits, based on artificial neural networks (ANNs), fractional order, etc. A non-linear model, less complex than the previous ones and whose behavior adequately represents the DLSCs, is the one formed by a variable capacitance, dependent on its internal voltage. This paper presents a mathematical study to obtain analytical expressions of all the electrical variables of DLSCs, voltage, current, dissipated power and so on, by means of a previous model. This study is carried out considering that the DLSC is charged and discharged through a voltage source and also discharged through a resistor. In later sections, the operational conditions of the DLSC in numerous industrial applications are presented. Finally, a comparative analysis is made between the results produced by the conventional model, with constant capacitance, and the developed model. This analysis is finally followed by the conclusions.
- 31 May 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (11) , 6714
Open AccessNon-Linear Analytical Model for the Study of Double-Layer Supercapacitors in Different Industrial Uses
It is generally considered that the representation of a double layer supercapacitor (DLSC) cannot be performed with the usual capacitance and resistance series connected, as it induces a relatively high level of inaccuracy in the results. In multiple previous studies, more advanced models have been developed with very different approaches: models with distributed parameter circuits, based on artificial neural networks (ANNs), fractional order, etc. A non-linear model, less complex than the previous ones and whose behavior adequately represents the DLSCs, is the one formed by a variable capacitance, dependent on its internal voltage. This paper presents a mathematical study to obtain analytical expressions of all the electrical variables of DLSCs, voltage, current, dissipated power and so on, by means of a previous model. This study is carried out considering that the DLSC is charged and discharged through a voltage source and also discharged through a resistor. In later sections, the operational conditions of the DLSC in numerous industrial applications are presented. Finally, a comparative analysis is made between the results produced by the conventional model, with constant capacitance, and the developed model. This analysis is finally followed by the conclusions.
- Open Access
- 26 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (9) , 5398
Sizing Methodology of a Fast Charger for Public Service Electric Vehicles Based on Supercapacitors
In this article, a new methodology for the sizing of a fast-charging station for electric vehicles is presented. The proposed method is applicable to public service vehicles on urban journeys. Its use has been conceived for vehicles equipped with an energy storage system based on supercapacitors (SCs), which are already functional in several countries. The proposed charging station also uses a bank of SCs of variable capacitance. During the study, mathematical expressions will be obtained for the electrical variables involved in vehicle charging: instantaneous current, peak current, charging time, dissipated energy, and the efficiency of energy transference. From these, each of the components of the system will be dimensioned: the capacitance of the charger with its different variable steps, the initial voltage of the charger, and the current smoothing inductor. The proposed charger presents the advantage of allowing energy to be evacuated to the electric vehicle very quickly and with high performance, all without using an external power source or high-power converters. The proposed architecture minimizes the disturbances that, with conventional methods, would appear on the electrical grid, preventing the installation of fast-charging stations at many grid nodes, as is currently the case. Finally, the charger control algorithm is considerably simplified as it only depends on the initial voltage of the vehicle’s accumulator.
- 26 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (9) , 5398
Open AccessSizing Methodology of a Fast Charger for Public Service Electric Vehicles Based on Supercapacitors
In this article, a new methodology for the sizing of a fast-charging station for electric vehicles is presented. The proposed method is applicable to public service vehicles on urban journeys. Its use has been conceived for vehicles equipped with an energy storage system based on supercapacitors (SCs), which are already functional in several countries. The proposed charging station also uses a bank of SCs of variable capacitance. During the study, mathematical expressions will be obtained for the electrical variables involved in vehicle charging: instantaneous current, peak current, charging time, dissipated energy, and the efficiency of energy transference. From these, each of the components of the system will be dimensioned: the capacitance of the charger with its different variable steps, the initial voltage of the charger, and the current smoothing inductor. The proposed charger presents the advantage of allowing energy to be evacuated to the electric vehicle very quickly and with high performance, all without using an external power source or high-power converters. The proposed architecture minimizes the disturbances that, with conventional methods, would appear on the electrical grid, preventing the installation of fast-charging stations at many grid nodes, as is currently the case. Finally, the charger control algorithm is considerably simplified as it only depends on the initial voltage of the vehicle’s accumulator.