ODOleksandr H. Dibir

Oleksandr H. Dibir

*This is an algorithmically generated author record based on publicly available information.

Oleksandr H. Dibir has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Discretization of Thin-Walled Sections with Variable Wall Thickness

    by National Aerospace University Kharkiv Aviation Institute, Mykhailo M. Hrebennikov, Oleksandr H. Dibir, Anatolii O. Kyrpikin

    At the stage of designing thin-walled aircraft structures, to simplify calculations, their cross sections are idealized. To do this, the section with the skin and the longitudinal elements reinforcing it is replaced (when determining normal stresses) by a discrete one, consisting of concentrated areas at characteristic points. In this case, the equality of the moments of inertia of the initial and discrete sections is preserved. Such idealization is used in the calculation of thin-walled rods for normal and shear stresses (Wagner model). For sections consisting of a system of rectangular strips of constant thickness, discretization allows to set approximate values of normal and shear stresses and accurately find the locations of the singular points of the bending center (in an open contour) and the center of rigidity (in a closed one). The discrete model of a strip consists of three lumped areas: two at the edges and one in the center. The paper proposes to extend the discrete model to sections in which the skin thickness changes according to a linear law. In addition to the rectangular strip, it is possible to use elongated triangles and trapezoids, replaced by three and four concentrated areas, respectively. The possibility of using a discrete model for calculating some thin-walled sections of open and closed contours is considered. The section of an open contour is studied - the problem of transverse bending without torsion of a channel having flanges with a linearly variable thickness. Differences in the flows of tangential forces calculated from the exact and discrete models are shown. The coincidence of the results in determining the position of the bending center according to two models was established. When studying the application of a discrete model to a closed contour, its simplified option is proposed. The problem of transverse bending without torsion and finding the center of rigidity in a section with a contour line in the form of a trapezoid with front and rear walls of constant thickness and upper and lower skins and a similar section with a contour in the form of a rectangle was considered. Differences in the flows of tangential forces calculated by exact and discrete models are established. For a closed section in the form of a rectangle, the decrease in the moment of inertia for torsion due to the redistribution of material in the cross section was studied separately. It has been established that when finding the position of the center of rigidity, the discrepancy between the results of the exact and discrete models in sections with geometric parameters close to real ones was less than 1% for a rectangular contour, and 4% for a trapezoidal contour. The results indicate the possibility of extending the application of the discrete model of thin-walled cross section to the design calculations of thin-walled rods with variable skin thickness, representing practical structures.

  • Open Access

    Calculation of the Tubular Elements Made of Pressed Profiles

    by National Aerospace University ", Mykhailo M. Hrebennikov, Kharkiv Aviation Institute, Oleksandr H. Dibir, National Aerospace University "Kharkiv Aviation Institute, Anatolii O. Kyrpikin, Mykola I. Pekelnyi

    This paper is dedicated to ensuring the strength of cargo equipment elements of transport aircraft. The strength of rollers of roller conveyors, which are made of standard pressed aluminum tubular profiles or composite tubular elements, is considered. The main disadvantage of these semi-finished products is the deviation of the diameter of these standard aluminum profiles, which leads to the emergence of eccentricity Δ between the axes of the outer and inner surfaces. The influence of eccentricity on the change in the values of normal and tangential stresses is considered. This analysis was carried out for standard diameters of tubular profiles at values Δ equal to half of the standard limit deviation of the outer diameter D. Calculations of normal and tangential stresses and their comparison with nominal stresses that occur in the absence of misalignment have been carried out. Calculations were made of the value c of the removal of the center of rigidity from the center of the circle of the outer border of the cross-section at different cross-section sizes of standard profiles with values of Δ equal to half of the standard limit deviation of the outer diameter D inclusively. The calculations showed an increase in tangential stresses τ in some cases by 64% and even by 213%. The obtained results indicate that the presence of Δ≠0 will have a negative effect on the resource of these elements. In order to eliminate the negative consequences, it is necessary to increase the requirements for the shape deviation of the tubular profiles in the input control.

  • Open Access

    Use of Logarithmic Decrement of Oscillation Damping for Prediction of the Aviation Structures Service Life

    by Mykhailo M. Hrebennikov, National Aerospace University Kharkiv Aviation Institute, Oleksandr H. Dibir, Anatolii O. Kyrpikin, Mykola I. Pekelnyi

    Problem of predicting the residual service life of airplanes and helicopters is highly relevant for flight safety. In this paper, on the basis of the conducted research on the change of mechanical characteristics during materials fatigue accumulation, it is proposed to control the service life by changing the dissipative characteristics. In case of fatigue damage, the accumulative logarithmic decrement of oscillation damping δ increases to the limit maximum value δm, which corresponds to the critical length of the main fatigue crack, which leads to failure. The limit value δm can be set depending on the amount of energy spent on the development of the main fatigue crack, taking into account the dangerous part of the consumed energy. With the accumulation of fatigue damage, the growth of logarithmic decrement occurs at the expense of energy expenditure for the growth of fatigue cracks and internal friction. This is taken into account by the coefficient α, which allows to allocate a dangerous part of the energy that goes into the development of a main fatigue crack. The problem of durability prediction consists of two stages. At first, it is needed to determine δm for the critical crack length. Then, based on the two values of logarithmic decrement at the corresponding load cycles, the number of cycles to failure – to the critical length of the crack – is predicted by the Peris formula