Tamara Braish
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tamara Braish has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Benoit Schmitt
Scientific and Technical Center for Building (CSTB), Health and Comfort Department, Saint-Martin-d'Hères, 38400, France; IPREM, IMT Mines Alès, Universite de Pau et des Pays de l'Adour, CNRS, Pau, 64000, France
1 shared publication Cécile Caudron
1 shared publication- Emmanuel Antczak
Univ. Artois, IMT Nord Europe, Junia, Univ. Lille, ULR 4515, Laboratoire de Génie Civil et Géo-Environnement (LGCgE), F-62400 Béthune, France
1 shared publication Franck Brachelet
1 shared publicationFrançois Maupetit
Scientific and Technical Center for Building (CSTB), Health and Comfort Department, Saint-Martin-d'Hères, 38400, France
1 shared publicationHervé Plaisance
IPREM, IMT Mines Alès, Universite de Pau et des Pays de l'Adour, CNRS, Pau, 64000, France
1 shared publication
Latest Publications
- 17 July 2025
- Published by Elsevier in Chemosphere
- Vol. 385, 144564
Development of measurement method for estimating gas-phase concentration of SVOCs in equilibrium with the source material surface at any temperature
- 17 July 2025
- Published by Elsevier in Chemosphere
- Vol. 385, 144564
Development of measurement method for estimating gas-phase concentration of SVOCs in equilibrium with the source material surface at any temperature
- Open Access
Impact of the Aging Process on the Ability of Decorative Materials Containing Biocides to Support Fungal Growth
Building and finishing materials are among the main sources of indoor air pollution and can provide ideal substrates for microbial growth. Environmental factors can induce physico-chemical aging of these materials, altering their composition and increasing their vulnerability to microbial growth. To mitigate this risk, manufacturers are increasingly adding biocidal agents to these materials to prevent microbial contamination. The aim of this project was to study the sensitivity of two different acrylic paints to fungal growth, before and after an aging process, and to assess the impact of aging on the effectiveness of the biocides contained in these materials. To do this, two paints (antifungal and normal paint) were applied to a wall covering (polyester-cellulose) before being subjected to accelerated aging. The later process was based on the addition of detergent or water and exposing the material to a visible light spectrum, moderate temperature (38 ± 6 °C), and ambient relative humidity (25 ± 17%). Prior to 30 days of incubation, the aged and unaged (“native”) materials were inoculated with fungal spores using a dry aerosolization system. Fungi behavior was then evaluated by the culture method. The results showed that the native and water-aged normal acrylic paint supported fungal growth at 95 ± 5% relative humidity. However, the use of the cleaning product during the aging process provided additional resistance of the materials against fungal growth. On the other hand, the antifungal paint showed no visible growth due to its biocide content. The accelerated aging and incubation processes led to the depletion of the biocides and thus a decrease in their effectiveness against mold development.
Open AccessImpact of the Aging Process on the Ability of Decorative Materials Containing Biocides to Support Fungal Growth
Building and finishing materials are among the main sources of indoor air pollution and can provide ideal substrates for microbial growth. Environmental factors can induce physico-chemical aging of these materials, altering their composition and increasing their vulnerability to microbial growth. To mitigate this risk, manufacturers are increasingly adding biocidal agents to these materials to prevent microbial contamination. The aim of this project was to study the sensitivity of two different acrylic paints to fungal growth, before and after an aging process, and to assess the impact of aging on the effectiveness of the biocides contained in these materials. To do this, two paints (antifungal and normal paint) were applied to a wall covering (polyester-cellulose) before being subjected to accelerated aging. The later process was based on the addition of detergent or water and exposing the material to a visible light spectrum, moderate temperature (38 ± 6 °C), and ambient relative humidity (25 ± 17%). Prior to 30 days of incubation, the aged and unaged (“native”) materials were inoculated with fungal spores using a dry aerosolization system. Fungi behavior was then evaluated by the culture method. The results showed that the native and water-aged normal acrylic paint supported fungal growth at 95 ± 5% relative humidity. However, the use of the cleaning product during the aging process provided additional resistance of the materials against fungal growth. On the other hand, the antifungal paint showed no visible growth due to its biocide content. The accelerated aging and incubation processes led to the depletion of the biocides and thus a decrease in their effectiveness against mold development.