Mariana Ferreira Benessiuti Motta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mariana Ferreira Benessiuti Motta has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Gabriel Orquizas Mattielo Pedroso
Department of Civil Engineering, Faculty of Engineering and Sciences, São Paulo State University, Guaratinguetá 12516-410, Brazil
4 shared publications - Emerson Felipe Felix
Universidade Estadual Paulista
3 shared publications - Tácio Mauro Pereira de Campos
Pontifícia Universidade Católica do Rio de Janeiro
2 shared publications Bruno da Silva de Oliveira
Centro Universitário Salesiano de São Paulo
1 shared publication- Carlos Manuel Andrade de Sousa
Department of Civil Engineering, School of Science and Engineering, São Paulo State University (UNESP), Guaratinguetá 12516-410, Brazil
1 shared publication - Cássio de Carvalho Araújo Moura
Centro Universitário Salesiano de São Paulo (UNISAL) - CAMPUS LORENA
1 shared publication
Latest Publications
- 29 May 2026
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 49 (3)
Estimating soil water retention curve in tropical residual soils: a comparative study of measurement and modeling techniques
This study evaluates various methods for estimating soil water retention curves (SWRCs) in tropical residual soils from the Baixada Santista region, Brazil, including both young and mature profiles. Laboratory data were obtained using HYPROP, WP4C, and the filter paper method, and curve fitting was performed using unimodal and bimodal van Genuchten models. The estimates were derived from mercury intrusion porosimetry (MIP), pedotransfer functions (PTF-SV and PTF-Bi), and inverse modeling with Hydrus-1D, using field moisture and rainfall data from CEMADEN. Model performance was assessed using RMSE, MAE, MBE, and correlation coefficients. For mature soils, PTF-SV showed the best statistical performance but failed to represent bimodal structure. In contrast, PTF-Bi and MIP better reflected dual porosity but with higher errors. For young soils, Hydrus-1D produced the best fit, especially in simpler pore systems. Although the models showed a strong correlation with laboratory data, they often yielded divergent van Genuchten parameters, indicating that statistical agreement does not necessarily ensure an accurate physical representation. No method consistently outperformed others across all soil types. These findings highlight the influence of soil structure and calibration data on model reliability and reinforce the need to develop tailored approaches for Brazilian tropical soils with complex hydraulic behavior.
- 29 May 2026
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 49 (3)
Estimating soil water retention curve in tropical residual soils: a comparative study of measurement and modeling techniques
This study evaluates various methods for estimating soil water retention curves (SWRCs) in tropical residual soils from the Baixada Santista region, Brazil, including both young and mature profiles. Laboratory data were obtained using HYPROP, WP4C, and the filter paper method, and curve fitting was performed using unimodal and bimodal van Genuchten models. The estimates were derived from mercury intrusion porosimetry (MIP), pedotransfer functions (PTF-SV and PTF-Bi), and inverse modeling with Hydrus-1D, using field moisture and rainfall data from CEMADEN. Model performance was assessed using RMSE, MAE, MBE, and correlation coefficients. For mature soils, PTF-SV showed the best statistical performance but failed to represent bimodal structure. In contrast, PTF-Bi and MIP better reflected dual porosity but with higher errors. For young soils, Hydrus-1D produced the best fit, especially in simpler pore systems. Although the models showed a strong correlation with laboratory data, they often yielded divergent van Genuchten parameters, indicating that statistical agreement does not necessarily ensure an accurate physical representation. No method consistently outperformed others across all soil types. These findings highlight the influence of soil structure and calibration data on model reliability and reinforce the need to develop tailored approaches for Brazilian tropical soils with complex hydraulic behavior.
- Open Access
- 2 September 2025
- Published by Fundacao de Apoio a Pesquisa, Tecnologia e Inovacao in Revista Ciências Exatas
- Vol. 31 (2)
ESTUDO DA PERMEABILIDADE E DA RESISTÊNCIA À TRAÇÃO DO REVESTIMENTO CPA APÓS COLMATAÇÃO INDUZIDA
Devido ao elevado número casos de acidentes em vias públicas causados por chuvas, o Brasil ao longo dos anos vem tentando aprimorar as condições dos pavimentos para minimizar essas ocorrências. Uma das soluções é o emprego da camada porosa de atrito (CPA), que é caracterizada por sua granulometria aberta fazendo com que a água escoe facilmente em seu meio. Porém, ao longo do tempo, com o elevado tráfego, os poros desse revestimento podem perder sua eficiência, devido ao acúmulo de resíduos. Este trabalho objetiva analisar a perda da permeabilidade após a impregnação de óleo automobilístico, borracha de pneu triturada e fragmentos de solo, simulando o derramamento ou respingos de fluidos de forma excessiva que acontece nas rodovias. Após quatro semanas de colmatação e ensaios, observou-se que a as amostras impregnadas tiveram a maior perda de permeabilidade comparado com os outros materiais. Após a realização dos ensaios de permeabilidade foi feito o teste de tração por compreensão diametral para analisar a interferência desses materiais na resistência do revestimento asfáltico. Observou- se que as amostras colmatadas com óleo tiveram sua estrutura modificada, pois o elemento o ligante interferiu na adesão com o agregado.
- 2 September 2025
- Published by Fundacao de Apoio a Pesquisa, Tecnologia e Inovacao in Revista Ciências Exatas
- Vol. 31 (2)
Open AccessESTUDO DA PERMEABILIDADE E DA RESISTÊNCIA À TRAÇÃO DO REVESTIMENTO CPA APÓS COLMATAÇÃO INDUZIDA
Devido ao elevado número casos de acidentes em vias públicas causados por chuvas, o Brasil ao longo dos anos vem tentando aprimorar as condições dos pavimentos para minimizar essas ocorrências. Uma das soluções é o emprego da camada porosa de atrito (CPA), que é caracterizada por sua granulometria aberta fazendo com que a água escoe facilmente em seu meio. Porém, ao longo do tempo, com o elevado tráfego, os poros desse revestimento podem perder sua eficiência, devido ao acúmulo de resíduos. Este trabalho objetiva analisar a perda da permeabilidade após a impregnação de óleo automobilístico, borracha de pneu triturada e fragmentos de solo, simulando o derramamento ou respingos de fluidos de forma excessiva que acontece nas rodovias. Após quatro semanas de colmatação e ensaios, observou-se que a as amostras impregnadas tiveram a maior perda de permeabilidade comparado com os outros materiais. Após a realização dos ensaios de permeabilidade foi feito o teste de tração por compreensão diametral para analisar a interferência desses materiais na resistência do revestimento asfáltico. Observou- se que as amostras colmatadas com óleo tiveram sua estrutura modificada, pois o elemento o ligante interferiu na adesão com o agregado.
- Open Access
- 21 July 2025
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 48 (3)
Soil-atmosphere interaction in geotechnics: some aspects concerning gravitational soil mass movements and biogas production and emissions in tropical environment
Soil-atmosphere interactions comprise a multidisciplinary and transdisciplinary subject of interest to numerous applied and research knowledge areas. In this work, aspects related to geotechnical, geoenvironmental and geological engineering, not usually considered in applied civil or environmental engineering projects, are put forward, exemplifying the role that micro-climatic conditions may have in the development of gravitational soil mass movements such as erosion processes and natural slope stability comprising unsaturated tropical soils. Based on literature data, proposals are put forward to consider cracks that develop under dry climatic conditions in engineering projects. Additionally, laboratory testing results indicate that the shear strength of soils may decrease due to climatic drywetting cycles, potentially compromising the accuracy of slope stability analysis results. In addition, the need to evaluate initial soil-water profile conditions in flow analysis is presented and discussed under various scenarios, and the effects of further atmospheric events, such as lightning, are also presented and discussed. Furthermore, based on data collected from diverse Brazilian sanitary landfills designed to operate primarily on municipal solid waste, relationships between soil-atmospheric variables and biogas generation and emission are investigated. Finally, based on the results generated in a physical model, a type of final municipal landfill cover is presented and discussed, whose design strongly depends on atmospheric data.
- 21 July 2025
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 48 (3)
Open AccessSoil-atmosphere interaction in geotechnics: some aspects concerning gravitational soil mass movements and biogas production and emissions in tropical environment
Soil-atmosphere interactions comprise a multidisciplinary and transdisciplinary subject of interest to numerous applied and research knowledge areas. In this work, aspects related to geotechnical, geoenvironmental and geological engineering, not usually considered in applied civil or environmental engineering projects, are put forward, exemplifying the role that micro-climatic conditions may have in the development of gravitational soil mass movements such as erosion processes and natural slope stability comprising unsaturated tropical soils. Based on literature data, proposals are put forward to consider cracks that develop under dry climatic conditions in engineering projects. Additionally, laboratory testing results indicate that the shear strength of soils may decrease due to climatic drywetting cycles, potentially compromising the accuracy of slope stability analysis results. In addition, the need to evaluate initial soil-water profile conditions in flow analysis is presented and discussed under various scenarios, and the effects of further atmospheric events, such as lightning, are also presented and discussed. Furthermore, based on data collected from diverse Brazilian sanitary landfills designed to operate primarily on municipal solid waste, relationships between soil-atmospheric variables and biogas generation and emission are investigated. Finally, based on the results generated in a physical model, a type of final municipal landfill cover is presented and discussed, whose design strongly depends on atmospheric data.
- Open Access
Sediment Barriers’ Performance in the Laboratory: Evaluation of Clogging and Filtration Characteristics in Geotextiles Subjected to Discharge Cycles
This research aims to assess the clogging process of geotextiles within silt fences. For that purpose, the filtering efficiency, flow rate, and clogging of three geotextiles (GTX-1, GTX-2, and GTX-3) employing two distinct soils and under three sediment discharge cycles were investigated. The analysis adhered to the American standard D5141-11 and, as further analyses, qualitative and quantitative inspections were conducted through microscopic images of the materials. The results showed greater clogging of the nonwoven geotextile, GTX-1, with higher retention efficiency (approximately 100%) and better turbidity removal for both soils, equal to a reduction of around 94%. For GTX-2, a woven geotextile with a larger pore opening, less intense clogging and lower retention efficiency were observed after the third discharge; the average was 96% for both soils. GTX-3, a woven geotextile with a smaller apparent opening, exhibited a behavior similar to GTX-1: as the number of cycles increased, the material experienced more clogging and higher retention efficiency for soil 1 (approximately 98.5%). Based on these findings, it can be inferred that the discharge cycles impact the tested geotextiles in diverse ways and, therefore, the selection of the material should be contingent on project requirements.
Open AccessSediment Barriers’ Performance in the Laboratory: Evaluation of Clogging and Filtration Characteristics in Geotextiles Subjected to Discharge Cycles
This research aims to assess the clogging process of geotextiles within silt fences. For that purpose, the filtering efficiency, flow rate, and clogging of three geotextiles (GTX-1, GTX-2, and GTX-3) employing two distinct soils and under three sediment discharge cycles were investigated. The analysis adhered to the American standard D5141-11 and, as further analyses, qualitative and quantitative inspections were conducted through microscopic images of the materials. The results showed greater clogging of the nonwoven geotextile, GTX-1, with higher retention efficiency (approximately 100%) and better turbidity removal for both soils, equal to a reduction of around 94%. For GTX-2, a woven geotextile with a larger pore opening, less intense clogging and lower retention efficiency were observed after the third discharge; the average was 96% for both soils. GTX-3, a woven geotextile with a smaller apparent opening, exhibited a behavior similar to GTX-1: as the number of cycles increased, the material experienced more clogging and higher retention efficiency for soil 1 (approximately 98.5%). Based on these findings, it can be inferred that the discharge cycles impact the tested geotextiles in diverse ways and, therefore, the selection of the material should be contingent on project requirements.
- Open Access
Influence of the ANN Hyperparameters on the Forecast Accuracy of RAC’s Compressive Strength
The artificial neural networks (ANNs)-based model has been used to predict the compressive strength of concrete, assisting in creating recycled aggregate concrete mixtures and reducing the environmental impact of the construction industry. Thus, the present study examines the effects of the training algorithm, topology, and activation function on the predictive accuracy of ANN when determining the compressive strength of recycled aggregate concrete. An experimental database of compressive strength with 721 samples was defined considering the literature. The database was used to train, validate, and test the ANN-based models. Altogether, 240 ANNs were trained, defined by combining three training algorithms, two activation functions, and topologies with a hidden layer containing 1–40 neurons. The ANN with a single hidden layer including 28 neurons, trained with the Levenberg–Marquardt algorithm and the hyperbolic tangent function, achieved the best level of accuracy, with a coefficient of determination equal to 0.909 and a mean absolute percentage error equal to 6.81%. Furthermore, the results show that it is crucial to avoid the use of overly complex models. Excessive neurons can lead to exceptional performance during training but poor predictive ability during testing.
Open AccessInfluence of the ANN Hyperparameters on the Forecast Accuracy of RAC’s Compressive Strength
The artificial neural networks (ANNs)-based model has been used to predict the compressive strength of concrete, assisting in creating recycled aggregate concrete mixtures and reducing the environmental impact of the construction industry. Thus, the present study examines the effects of the training algorithm, topology, and activation function on the predictive accuracy of ANN when determining the compressive strength of recycled aggregate concrete. An experimental database of compressive strength with 721 samples was defined considering the literature. The database was used to train, validate, and test the ANN-based models. Altogether, 240 ANNs were trained, defined by combining three training algorithms, two activation functions, and topologies with a hidden layer containing 1–40 neurons. The ANN with a single hidden layer including 28 neurons, trained with the Levenberg–Marquardt algorithm and the hyperbolic tangent function, achieved the best level of accuracy, with a coefficient of determination equal to 0.909 and a mean absolute percentage error equal to 6.81%. Furthermore, the results show that it is crucial to avoid the use of overly complex models. Excessive neurons can lead to exceptional performance during training but poor predictive ability during testing.
- Open Access
- 25 October 2023
- Published by Associacao Nacional de Tecnologia do Ambiente Construido (ANTAC) in ENCONTRO NACIONAL DE APROVEITAMENTO DE RESÍDUOS NA CONSTRUÇÃO
- Vol. 8, 1-6
Avaliação mecânica do uso de resíduo de fresagem de pavimentos na estabilização de um solo siltoso
Na Engenharia Civil, atualmente, medidas como reciclagem, reaproveitamento e reutilização são essenciais nas práticas da profissão. Sendo assim, no ramo de pavimentação há diversas iniciativas para utilizar materiais provenientes da fresagem da camada asfáltica do pavimento. O material fresado, quando descartado incorretamente, se torna um resíduo agressivo ao meio ambiente, tornando sua reutilização necessária. Desse modo, o objeto deste estudo é verificar a aplicação do resíduo de fresagem na estabilização de um solo siltoso, a fim de utilizar a mistura dos materiais nas camadas do pavimento. Para tanto, o material fresado foi incorporado ao solo, nas proporções de 25; 50 e 75%, e verificado suas propriedades físicas e mecânicas por meio dos ensaios de granulometria, compactação e Índice de Suporte California (ISC ou CBR). Os resultados mostraram que conforme foi sendo adicionado material fresado, os valores de massa específica máxima seca aumentam, o teor de umidade ótima diminui, e a expansão do solo diminui. Entretanto, embora houve a diminuição da expansão, não houve uma variação significativa no valor do CBR, assim, para que as misturas possam ser aplicadas em outras camadas do pavimento flexível, essas não satisfazem as condições mínimas do DNIT para utilização em camadas de base e sub-base.
- 25 October 2023
- Published by Associacao Nacional de Tecnologia do Ambiente Construido (ANTAC) in ENCONTRO NACIONAL DE APROVEITAMENTO DE RESÍDUOS NA CONSTRUÇÃO
- Vol. 8, 1-6
Open AccessAvaliação mecânica do uso de resíduo de fresagem de pavimentos na estabilização de um solo siltoso
Na Engenharia Civil, atualmente, medidas como reciclagem, reaproveitamento e reutilização são essenciais nas práticas da profissão. Sendo assim, no ramo de pavimentação há diversas iniciativas para utilizar materiais provenientes da fresagem da camada asfáltica do pavimento. O material fresado, quando descartado incorretamente, se torna um resíduo agressivo ao meio ambiente, tornando sua reutilização necessária. Desse modo, o objeto deste estudo é verificar a aplicação do resíduo de fresagem na estabilização de um solo siltoso, a fim de utilizar a mistura dos materiais nas camadas do pavimento. Para tanto, o material fresado foi incorporado ao solo, nas proporções de 25; 50 e 75%, e verificado suas propriedades físicas e mecânicas por meio dos ensaios de granulometria, compactação e Índice de Suporte California (ISC ou CBR). Os resultados mostraram que conforme foi sendo adicionado material fresado, os valores de massa específica máxima seca aumentam, o teor de umidade ótima diminui, e a expansão do solo diminui. Entretanto, embora houve a diminuição da expansão, não houve uma variação significativa no valor do CBR, assim, para que as misturas possam ser aplicadas em outras camadas do pavimento flexível, essas não satisfazem as condições mínimas do DNIT para utilização em camadas de base e sub-base.
- Open Access
Flexural Strength Characteristics of Fiber-Reinforced Cemented Soil
This work deals with the flexural performance of a soil-cement for pavement reinforced by polypropylene and steel fibers, and the main purpose is to evaluate the effect of different curing times. In this sense, three different curing times were employed to investigate the influence of fibers on the material’s behavior at varying levels of strength and stiffness as the matrix became increasingly rigid. An experimental program was developed to analyze the effects of incorporating different fibers in a cemented matrix for pavement applications. Polypropylene and steel fibers were used at 0.5/1.0/1.5% fractions by volume for three different curing times (3/7/28 days) to assess the fiber effect in the cemented soil (CS) matrices throughout time. An evaluation of the material performance was carried out using the 4-Point Flexural Test. The results show that steel fibers with 1.0% content improved by approximately 20% in terms of initial strength and peak strength at small deflections without interfering the flexural static modulus of the material. The polypropylene fiber mixtures had better performance in terms of ductility index reaching values varying from 50 to 120, an increase of approximately 40% in residual strength, and improved cracking control at large deflections. The current study shows that fibers significantly affect the mechanical performance of CSF. Thus, the overall performance presented in this study is useful for selecting the most suitable fiber type corresponding to the different mechanisms as a function of curing time.
Open AccessFlexural Strength Characteristics of Fiber-Reinforced Cemented Soil
This work deals with the flexural performance of a soil-cement for pavement reinforced by polypropylene and steel fibers, and the main purpose is to evaluate the effect of different curing times. In this sense, three different curing times were employed to investigate the influence of fibers on the material’s behavior at varying levels of strength and stiffness as the matrix became increasingly rigid. An experimental program was developed to analyze the effects of incorporating different fibers in a cemented matrix for pavement applications. Polypropylene and steel fibers were used at 0.5/1.0/1.5% fractions by volume for three different curing times (3/7/28 days) to assess the fiber effect in the cemented soil (CS) matrices throughout time. An evaluation of the material performance was carried out using the 4-Point Flexural Test. The results show that steel fibers with 1.0% content improved by approximately 20% in terms of initial strength and peak strength at small deflections without interfering the flexural static modulus of the material. The polypropylene fiber mixtures had better performance in terms of ductility index reaching values varying from 50 to 120, an increase of approximately 40% in residual strength, and improved cracking control at large deflections. The current study shows that fibers significantly affect the mechanical performance of CSF. Thus, the overall performance presented in this study is useful for selecting the most suitable fiber type corresponding to the different mechanisms as a function of curing time.
- Open Access
- 27 April 2023
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 46 (2)
Influence of coconut fiber on the microstructural, mechanical and hydraulic behavior of unsaturated compacted soil
This study aimed to evaluate the influence of the addition of coconut (coir) fibers on the microstructural, hydraulic and mechanical behavior of an unsaturated compacted soil. Specimens were molded and compacted, forming composites with 0%, 0.1%, 0.5% and 1% fiber in relation to their dry mass. The characterization of pores from the soil and fiber soil mixtures was performed by the Mercury Intrusion Porosimetry tests. Suction values were obtained through the filter paper method and soil water retention curves were adjusted with the Durner model due to the bimodal behavior. Tensile strength values were obtained from the indirect tensile strength test (Brazilian tensile test) for specimens with different suction values. It was found that the increase in fiber content in the material lead to a non-linear increase in macropores, which affected both the hydraulic and mechanical behavior of the soil. Furthermore, the shape of the soil water retention curve was preserved, but there were changes in the values of first and second air entry and residual suction. The tensile strength was negatively influenced, reaching a reduction of about 30% in the situation with higher fiber content. However, for higher levels, the behavior of the soil changed from brittle to ductile, increasing the supported deformations.
- 27 April 2023
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 46 (2)
Open AccessInfluence of coconut fiber on the microstructural, mechanical and hydraulic behavior of unsaturated compacted soil
This study aimed to evaluate the influence of the addition of coconut (coir) fibers on the microstructural, hydraulic and mechanical behavior of an unsaturated compacted soil. Specimens were molded and compacted, forming composites with 0%, 0.1%, 0.5% and 1% fiber in relation to their dry mass. The characterization of pores from the soil and fiber soil mixtures was performed by the Mercury Intrusion Porosimetry tests. Suction values were obtained through the filter paper method and soil water retention curves were adjusted with the Durner model due to the bimodal behavior. Tensile strength values were obtained from the indirect tensile strength test (Brazilian tensile test) for specimens with different suction values. It was found that the increase in fiber content in the material lead to a non-linear increase in macropores, which affected both the hydraulic and mechanical behavior of the soil. Furthermore, the shape of the soil water retention curve was preserved, but there were changes in the values of first and second air entry and residual suction. The tensile strength was negatively influenced, reaching a reduction of about 30% in the situation with higher fiber content. However, for higher levels, the behavior of the soil changed from brittle to ductile, increasing the supported deformations.
- 1 January 2023
- Published by Editora Cubo
- p. 623-658
Resistência ao cisalhamento de solos não saturados