Tobias Ziegelwanger
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tobias Ziegelwanger has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Jozef Keckes
Christian Doppler Laboratory for Knowledge-Based Design of Advanced Steels, Department of Materials Science, Montanuniversität Leoben, 8700 Leoben, Austria
4 shared publications - Michael Meindlhumer
Department of Materials Science, Montanuniversität Leoben, Leoben, Austria
4 shared publications M. Reisinger
3 shared publications- Juraj Todt
Department of Materials Science, Montanuniversität Leoben, Franz Josef-Straße 18, 8700 Leoben, Austria
2 shared publications K. Hlushko
2 shared publicationsA.A. Medjahed
European Synchrotron Radiat Facil, 71 Ave Martyrs, F-38043 Grenoble, France
1 shared publication
Latest Publications
- Open Access
- 2 May 2025
- Published by Elsevier in Materials & Design
- Vol. 254
Multilayer design of sustainable multifunctional Zr–Cu–N coatings: A route for enhanced mechanical and antibacterial performance
- 2 May 2025
- Published by Elsevier in Materials & Design
- Vol. 254
Open AccessMultilayer design of sustainable multifunctional Zr–Cu–N coatings: A route for enhanced mechanical and antibacterial performance
- Open Access
- 31 January 2025
- Published by Elsevier in Materials & Design
- Vol. 251
20 kHz X-ray diffraction on Cu thin films explores thermomechanical fatigue at high strain-rates
- 31 January 2025
- Published by Elsevier in Materials & Design
- Vol. 251
Open Access20 kHz X-ray diffraction on Cu thin films explores thermomechanical fatigue at high strain-rates
- Open Access
- 8 June 2024
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 181
Backside metallization affects residual stress and bending strength of the recast layer in laser-diced Si
- 8 June 2024
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 181
Open AccessBackside metallization affects residual stress and bending strength of the recast layer in laser-diced Si
- 12 January 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (2)
Micromechanical properties of micro- and nanocrystalline CVD diamond thin films with gradient microstructures and stresses
Chemical vapor deposition produced diamonds attract considerable scientific and industrial interest due to their exceptional mechanical and functional properties. Here, hot filament (HF) chemical vapor deposition was used to synthesize two diamond thin films with different cross-sectional microstructure and residual stresses. Structural characterization by scanning electron microscopy, Raman spectroscopy, and cross-sectional synchrotron x-ray nanodiffraction revealed different diamond morphologies. While the microcrystalline diamond film exhibits pronounced microstructural gradients expressed by gradually increasing (i) intensities of the 111 Debye-Scherrer rings, (ii) ⟨110⟩ fiber texture sharpness, (iii) grain size, and (iv) slightly oscillating residual stress at the level of −0.5 GPa, the nanocrystalline diamond film showed no pronounced cross-sectional variation of microstructure above the nucleation zone of ∼0.5 μm and a steady stress level of 0.25 GPa. In situ micromechanical cantilever bending tests revealed highly different mechanical properties of the two films. In detail, Young's modulus of 830 ± 53 and 459 ± 53 GPa, fracture stress of 12.4 ± 0.8 and 7.8 ± 1.0 GPa, and fracture toughness values of 6.9 ± 0.4 and 3.6 ± 0.3 MPa⋅m½ were evaluated for the micro- and nanocrystalline diamond films, respectively. In summary, this study provides valuable insights into the microstructure-residual stress correlation in micro- and nanocrystalline diamond films, especially illuminating their influence on micromechanical properties.
- 12 January 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (2)
Micromechanical properties of micro- and nanocrystalline CVD diamond thin films with gradient microstructures and stresses
Chemical vapor deposition produced diamonds attract considerable scientific and industrial interest due to their exceptional mechanical and functional properties. Here, hot filament (HF) chemical vapor deposition was used to synthesize two diamond thin films with different cross-sectional microstructure and residual stresses. Structural characterization by scanning electron microscopy, Raman spectroscopy, and cross-sectional synchrotron x-ray nanodiffraction revealed different diamond morphologies. While the microcrystalline diamond film exhibits pronounced microstructural gradients expressed by gradually increasing (i) intensities of the 111 Debye-Scherrer rings, (ii) ⟨110⟩ fiber texture sharpness, (iii) grain size, and (iv) slightly oscillating residual stress at the level of −0.5 GPa, the nanocrystalline diamond film showed no pronounced cross-sectional variation of microstructure above the nucleation zone of ∼0.5 μm and a steady stress level of 0.25 GPa. In situ micromechanical cantilever bending tests revealed highly different mechanical properties of the two films. In detail, Young's modulus of 830 ± 53 and 459 ± 53 GPa, fracture stress of 12.4 ± 0.8 and 7.8 ± 1.0 GPa, and fracture toughness values of 6.9 ± 0.4 and 3.6 ± 0.3 MPa⋅m½ were evaluated for the micro- and nanocrystalline diamond films, respectively. In summary, this study provides valuable insights into the microstructure-residual stress correlation in micro- and nanocrystalline diamond films, especially illuminating their influence on micromechanical properties.
- Open Access
- 27 April 2023
- Published by Elsevier in Acta Materialia
- Vol. 253
Intragranular thermal fatigue of Cu thin films: Near-grain boundary hardening, strain localization and voiding
- 27 April 2023
- Published by Elsevier in Acta Materialia
- Vol. 253
Open AccessIntragranular thermal fatigue of Cu thin films: Near-grain boundary hardening, strain localization and voiding