Sukhendu Sadhukhan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sukhendu Sadhukhan has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
Ayan Mitra
5 shared publications- Pabitra Kumar Chakrabarti
Solid State Research Laboratory, Department of Physics, Burdwan University, Burdwan, India
5 shared publications Chandi Charan Dey
4 shared publicationsPabitra K. Chakrabarti
4 shared publicationsAbhik S. Mahapatra
3 shared publicationsArpita Mondal
3 shared publications
Latest Publications
- Open Access
- 15 October 2026
- Published by Wiley in Advanced Functional Materials
- p. e78986
A Miniaturized Autonomous Thermomagnetic Generator
Thermomagnetic generators (TMG) are promising devices for converting low‐grade waste heat into electricity. Self‐actuation using permanent magnets is the key to autonomy. Tailoring thermomagnetic materials in the form of flexible and freestanding films is a way toward high power‐density through fast, and efficient heat transfer. Design optimization, and the use of micromagnets represent a unique opportunity toward miniaturization. Here, the operation and performance of a TMG using a flexible freestanding Gd film as the active substance, and an array of NdFeB micromagnets as field source is presented. The Gd film self oscillates under the effect of the magnetic field gradient, entering in contact with the heat source, and the heat sink alternatively. At an operating frequency of Hz, a designed piezoelectric spring converts the mechanical oscillation into electrical energy, reaching up to power‐output with temperature difference. The magnetic field gradient acting over the thermal switch, and triggering the caloric response of this thick Gd film, is generated by an array of thick NdFeB micromagnets, which produces a T variation in field strength over a gap. The power density normalized to the combined volume of the Gd film and of the magnet reaches up to .
- 15 October 2026
- Published by Wiley in Advanced Functional Materials
- p. e78986
Open AccessA Miniaturized Autonomous Thermomagnetic Generator
Thermomagnetic generators (TMG) are promising devices for converting low‐grade waste heat into electricity. Self‐actuation using permanent magnets is the key to autonomy. Tailoring thermomagnetic materials in the form of flexible and freestanding films is a way toward high power‐density through fast, and efficient heat transfer. Design optimization, and the use of micromagnets represent a unique opportunity toward miniaturization. Here, the operation and performance of a TMG using a flexible freestanding Gd film as the active substance, and an array of NdFeB micromagnets as field source is presented. The Gd film self oscillates under the effect of the magnetic field gradient, entering in contact with the heat source, and the heat sink alternatively. At an operating frequency of Hz, a designed piezoelectric spring converts the mechanical oscillation into electrical energy, reaching up to power‐output with temperature difference. The magnetic field gradient acting over the thermal switch, and triggering the caloric response of this thick Gd film, is generated by an array of thick NdFeB micromagnets, which produces a T variation in field strength over a gap. The power density normalized to the combined volume of the Gd film and of the magnet reaches up to .
- 14 August 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (26) , 49480-49491
Field-dependent magnetic ordering and electrical properties of YCr0.95Mn0.05O3 nanoparticles
- 14 August 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (26) , 49480-49491
Field-dependent magnetic ordering and electrical properties of YCr0.95Mn0.05O3 nanoparticles
- 2 March 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (12) , 18699-18714
Modulated magnetic and wideband tunable microwave absorption properties of multiferroic nanocomposite (BiFeO3)0.5(ZnO)0.5 in the matrix of multiwalled carbon nanotube (MWCNT)
- 2 March 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (12) , 18699-18714
Modulated magnetic and wideband tunable microwave absorption properties of multiferroic nanocomposite (BiFeO3)0.5(ZnO)0.5 in the matrix of multiwalled carbon nanotube (MWCNT)
- Open Access
- 23 February 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (11) , 17595-17606
Electrocaloric cooling efficiency: Comparative insights on P(VDF-TrFE-CFE) polymer and BSTM ceramics
- 23 February 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (11) , 17595-17606
Open AccessElectrocaloric cooling efficiency: Comparative insights on P(VDF-TrFE-CFE) polymer and BSTM ceramics
- Open Access
- 7 February 2026
- Published by Elsevier in SSRN Electronic Journal
Electrocaloric Cooling efficiency: Comparative Insights on P(VDF-TrFE-CFE) polymer and BSTM ceramics
In response to the increasing demand for efficient and compact refrigeration and energy conversion devices, research has focused on identifying optimal electrocaloric (EC) materials among ferroelectric ceramics and polymers. This study investigates the EC properties of the Poly [(Vinylidene Fluoride)0.664-(Trifluoroethylene)0.245-(Chlorofluoroethylene)0.91] terpolymer and multi-layer Ba0.6Sr0.4Ti0.998Mn0.002O3 (BSTM) ceramics, comparing various parameters to assess their suitability for advanced energy applications. The multilayer ceramic capacitor contains a large amount of inactive material, which hinders the performance of the capacitor both in terms of ΔTad and efficiency. Finite-element modeling with direct temperature measurement was therefore employed to extract intrinsic electrocaloric response from geometric and diffusion effects, providing the ΔTad and diffusion-related energy losses required for evaluating the cooling efficiency. Adiabatic temperature change (ΔTad) obtained in an electric field representing long-term operation, reaches 4.91 °C for Terpo at 100 V/μm and 3.0 °C for BSTM at 30 °C. The loss in ferroelectric hysteresis is observed to be much lower in BSTM than in PVDF Terpolymer. Hence, the cooling efficiency relative to Carnot reveals that the PVDF Terpolymer achieves a relative cooling efficiency upper bound of 4.5% at 100 V/μm, whereas BSTM ceramics reach nearly 14 times, being 62.1% at 30 V/μm. The PVDF Terpolymer outperforms BSTM ceramics in terms of adiabatic temperature change and flexibility, but not in terms of expected cooling efficiency. Considering these complementary strengths, both BSTM ceramics and PVDF terpolymers emerge as promising electrocaloric materials for advanced energy applications, including solid-state cooling and energy harvesting.
- 7 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessElectrocaloric Cooling efficiency: Comparative Insights on P(VDF-TrFE-CFE) polymer and BSTM ceramics
In response to the increasing demand for efficient and compact refrigeration and energy conversion devices, research has focused on identifying optimal electrocaloric (EC) materials among ferroelectric ceramics and polymers. This study investigates the EC properties of the Poly [(Vinylidene Fluoride)0.664-(Trifluoroethylene)0.245-(Chlorofluoroethylene)0.91] terpolymer and multi-layer Ba0.6Sr0.4Ti0.998Mn0.002O3 (BSTM) ceramics, comparing various parameters to assess their suitability for advanced energy applications. The multilayer ceramic capacitor contains a large amount of inactive material, which hinders the performance of the capacitor both in terms of ΔTad and efficiency. Finite-element modeling with direct temperature measurement was therefore employed to extract intrinsic electrocaloric response from geometric and diffusion effects, providing the ΔTad and diffusion-related energy losses required for evaluating the cooling efficiency. Adiabatic temperature change (ΔTad) obtained in an electric field representing long-term operation, reaches 4.91 °C for Terpo at 100 V/μm and 3.0 °C for BSTM at 30 °C. The loss in ferroelectric hysteresis is observed to be much lower in BSTM than in PVDF Terpolymer. Hence, the cooling efficiency relative to Carnot reveals that the PVDF Terpolymer achieves a relative cooling efficiency upper bound of 4.5% at 100 V/μm, whereas BSTM ceramics reach nearly 14 times, being 62.1% at 30 V/μm. The PVDF Terpolymer outperforms BSTM ceramics in terms of adiabatic temperature change and flexibility, but not in terms of expected cooling efficiency. Considering these complementary strengths, both BSTM ceramics and PVDF terpolymers emerge as promising electrocaloric materials for advanced energy applications, including solid-state cooling and energy harvesting.
- 25 January 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (9) , 12033-12050
Improvement of magneto-electric properties of YFeO3 by co-doping with Gd3+ and Ti4+ in the system of Y0.95Gd0.05Fe0.95Ti0.05O3
- 25 January 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (9) , 12033-12050
Improvement of magneto-electric properties of YFeO3 by co-doping with Gd3+ and Ti4+ in the system of Y0.95Gd0.05Fe0.95Ti0.05O3
- 4 June 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (22) , 37834-37848
Enhanced multiferroicity of LaFeO3 nanoparticle system in La0.9Er0.1FeO3
- 4 June 2025
- Published by Elsevier in Ceramics International
- Vol. 51 (22) , 37834-37848
Enhanced multiferroicity of LaFeO3 nanoparticle system in La0.9Er0.1FeO3
- 23 January 2025
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 616
Microwave absorption and magnetic properties of Ni-NiO-GO nanocomposites
- 23 January 2025
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 616
Microwave absorption and magnetic properties of Ni-NiO-GO nanocomposites