ATAbrham Gebre Tarekegn

Abrham Gebre Tarekegn

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Abrham Gebre Tarekegn has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effects of Irregular Polygonal Coated Aggregates on Damping Behavior of Concrete: A Two-Dimensional Simulation

    by Yisihak Gebre Tarekegn, Tom Lahmer, Abrham Gebre Tarekegn

    The numerical representation of aggregate shape and surface characteristics is essential for predicting the dynamic behavior of concrete with coated aggregates. However, the effects of realistic irregular aggregate shape on the numerical prediction of damping behavior remain insufficiently investigated. This study presents a two-dimensional numerical investigation of the effects of aggregate coating and irregular polygonal aggregate shape on the dynamic behavior of concrete. Aggregates with irregular shapes were modeled with and without coating layers using finite element simulations in Abaqus/CAE 6.14-1. The irregular polygonal aggregate shapes were generated using Python 3.12.4 and incorporated into the numerical models. The aggregate size was selected within the range of 8.0–25.0 mm and the replacement level of coating aggregates varied from 5% to 20%. The numerical results were compared with circular and elliptical aggregate models and also with experimental results reported in previous studies. The irregular polygonal aggregate model showed strong agreement with experimental results, with numerical-to-experimental ratios ranging from 0.90 to 1.02 and deviations of approximately 1% to 10% across the investigated concrete with coated aggregates. Moreover, the statistical comparison indicates that the irregular polygonal aggregate model provides the closest agreement between the numerical and experimental damping ratios. It exhibits the lowest MAE (0.163%), RMSE (0.191%), and MAPE (3.522%), together with the highest coefficient of determination (R2 = 0.812). Furthermore, the results indicate that replacing 15% of the coarse aggregates with rubber-coated aggregates resulted in a damping ratio of 5.13%, representing a 16.86% increase compared with conventional concrete. The results demonstrate that aggregate geometry and coating material significantly influence the dynamic response of concrete, with elliptical and irregular aggregate representations providing closer agreement with experimental observations than circular inclusions.

  • Open Access

    Interactive Effects of Node, Location and Loading Orientation on the Flexural Properties of Ethiopian Highland Bamboo ( Oldeania alpina (K. Schum.) Stapleton)

    by Beharu Shikur, Girma Zerayohannes, Abrham Tarekegn

    The flexural behavior of 180 split bamboo samples was examined in this study, along with the impacts of loading orientation, culm location and node presence on Ol deania alpina flexural properties. The material’s anisotropic, functionally graded anatomy was confirmed by the results, which showed significant main effects of node presence and loading orientation on flexural stiffness ( MOE f ) and strength (MOR) (p < 0.001). Nodes improved both properties ( MOE f 62%; MOR 49%), establishing it as the primary contribution, while outer compression produced superior performance ( MOE f 26%; MOR 18%). The top sections deformed 37% more than the bottom sections due to a significant thickness gradient, and position significantly influenced the MOE f (p = 0.024), with the middle culm sections exhibiting the highest values. Crucially, the outer compression mode significantly increased the node's stiffening impact, with flexural stiffness and strength reaching values as high as 18.29 GPa and 234.26 MPa, according to a significant Node × Loading Orientation interaction. This, together with a Node × Location interaction, suggested that the node's ability to reinforce changes across the culm. The load-deflection curves and flexural stress-strain behaviour were explained by the hierarchical structure of bamboo. According to the study’s findings, Oldeania alpina is a hierarchically optimized natural composite whose remarkable performance results from the coordinated use of longitudinal direction, loading orientation and nodal architecture. These findings offer recommendations for the high-performance use of this bamboo in structural design.

  • Open Access

    Dynamic Response of 3D Concrete Beams with Coated Aggregates Under Wave Propagation Induced by Piezoelectric Actuators: A Simulation Study

    by Yisihak Gebre Tarekegn, Tom Lahmer, Abrham Gebre Tarekegn

    This research investigates the dynamic response of three-dimensional concrete beams with coated aggregates subjected to transient wave propagation induced by piezoelectric actuators (PZT-lead zirconate titanate). The aim was to assess the effects of coated aggregates on concrete’s damping behavior and wave attenuation. The effect of various coating materials (epoxy and rubber) and replacement levels ranging from 5% to 25% by volume of the natural coarse aggregates on wave attenuation and energy dissipation were investigated through Finite Element Modeling (FEM) using Abaqus/CAE 6.14-1 software. Moreover, the effect of coating thickness is investigated for thicknesses ranging from 1.0 mm to 3.5 mm. The findings show that the replacement level, coating thickness, and coating material have a major effect on damping characteristics of concrete. It was also observed that rubber-coated aggregates with a 3.0 mm coating thickness (20% replacement level) exhibited an optimal damping ratio of 6.15%, representing a 29.5% increase, and offer enhanced energy dissipation, better damping performance, and the ability to alter wave travel paths, all of which could be advantageous for Structural Health Monitoring (SHM) applications. In line with this, the damping ratio of concrete beam models with epoxy- and rubber-coated aggregates, embedded with PZT material, was significantly higher (by approximately 1% to 18%) compared to that of the concrete model without PZT materials. Additionally, the findings showed that the concrete’s damping properties were greatly impacted by the interaction between PZT materials and coated aggregates. All things considered, the dynamic response and damping performance of concrete with coated-aggregate surface properties were successfully assessed using PZT-based simulations.

  • Open Access

    Analyzing land use diversity around Addis Ababa Light Rail Transit stations: Integrating AHP and GIS

    by Ashenafi Wondimu Tekolla, Abrham Gebre Tarekegn, Segne Getu Tulu

    Land use diversity is the main prerequisite for sustainable urban development models such as Transit Oriented Development (TOD). Understanding the existing land use composition is essential when planning to implement TOD. This study assesses the level of land use diversity within an 800 m radius of four stations along the Addis Ababa Light Rail Transit (LRT), located in the central Business District (CBD). The methodology integrates the Analytic Hierarchy Process (AHP) with the Geographical Information System (GIS) using the Weighted Overlay Analysis tool. This method assigns relative weights to key land-use diversity indicators using the AHP method. The weighted layers are overlaid in GIS to generate composite land use diversity represented by three different colors (green, yellow, and red representing high, moderate, and low diversity, respectively) on a spatial map. The results of the analysis revealed that 68.18% of the study area exhibits a moderate level of land use diversity, followed by 18.91% high and 12.91% low levels. Spatial analysis also revealed the ratio of diversity variance among the four stations, indicating Autobus Tera station has the highest level of diversity among the others. The results offer a clear visual representation of diversity levels and provide valuable input for planners and decision-makers seeking to promote more diversified land use to enhance an integrated, transitsupportive urban form. This research demonstrates the effectiveness of integrating AHP-GIS as a decision-support tool for assessing land use diversity and guiding strategic interventions to improve.

  • Open Access

    Three-Dimensional Simulation on the Influence of Coated Rubber Chips on Concrete Properties

    by Yisihak Gebre Tarekegn, Tom Lahmer, Abrham Gebre Tarekegn, Esayas Gebreyouhannes Ftwi

    Rubber chips, when used as a partial replacement for coarse aggregates in concrete, tend to increase ductility, absorb energy, and can be beneficial due to their ability to reduce impact forces and dampen vibrations. However, they lead to a substantial decrease in compressive strength compared to ordinary concrete. Due to the weak bond between rubber particles and the concrete matrix, sand-coating surface treatment was applied to enhance the interfacial properties of the rubber surface. In this research, a detailed numerical analysis was conducted in order to predict the mechanical and dynamic behavior of concrete by incorporating partially replaced coarse aggregates with uncoated and sand-coated rubber chips. The study also seeks to examine the effects of rubber inclusion on key parameters such as damping ratio and compressive strength, thereby providing insights into the effectiveness of using recycled rubber as a sustainable alternative material in concrete production. The compressive strength and damping ratio of concrete were examined through a three-dimensional numerical simulation using ABAQUS/CAE 6.14-1. The results demonstrated that the optimal compressive strength was achieved with a 15% sand-coated rubber replacement, resulting in a 15.67% increment. Furthermore, the maximum improvements in damping ratios were observed to be 48.42% for uncoated rubber chips and 25% for coated ones, when compared to conventional concrete. These enhancements highlight the potential of both coated and uncoated rubber inclusions, due to rubber’s high elasticity. Moreover, at optimized levels, improved concrete properties can be achieved while promoting sustainability through material reuse.


  • Live Load Models for Ethiopian Highway Bridges using Truck Weigh-in-Motion Data

    by Abrham Gebre, Binyam Wesenseged, Yisihak Gebre, Getu Segni

    For the structural analysis of highway bridges, as heavy trucks cause large loads, development of live load models based on empirical data is critical. Therefore, weigh-in-motion (WIM) technology provides essential insights into axle configurations, vehicle weights, and traffic patterns that is vital in bridge construction and evaluation. This research examines the impact of truck loads on bridges, using information obtained from the WIM systems in Ethiopia. A new live load model specific to the country is developed based on 5 years of WIM data, encompassing 45,197 heavy truck loadings identified through systematic sampling methods. For simply supported bridges up to 50 m, the static load calculations are also performed, and a statistical extrapolation is used to obtain the results for a 75-year return period. Results showed that the extrapolated WIM data exceeds the factored HL-93 load effects by 15% on average. Finally, live load models which reflect the country’s actual loading conditions are proposed, with an error of below 9.48% compared with extrapolated data.


  • Open Access

    Effects of Coating Thickness and Aggregate Size on the Damping Properties of Concrete: A Numerical Simulation Approach

    by Yisihak Gebre Tarekegn, Tom Lahmer, Abrham Gebre Tarekegn, Esayas Gebreyouhannes Ftwi

    Concrete properties are investigated using intensive physical testing processes that require large amounts of labor and materials that are costly and time-consuming. Properly validated computer models can replace most of the existing physical testing procedures with computer simulations that are relatively quick and inexpensive. Therefore, in this study, the effects of coating thickness and aggregate size on the damping properties of concrete were investigated using numerical simulation with Abaqus/CAE 6.14-1 software. Two different groups of aggregates were used in the simulation, with maximum aggregate sizes of 25 mm and 32 mm. The coating thickness ranged from 0.4 mm to 5.0 mm, using epoxy, silicone, and rubber coatings. The results showed that coatings with smaller aggregate size led to an increase in the damping ratio compared to those with larger aggregate size. Moreover, replacing 20% of coarse aggregates with rubber-coated aggregates results in a damping ratio of 5.75% to 6.21%, reflecting an increase of 22.8% to 32.7%. This variation occurs with coating thicknesses ranging from 0.4 mm to 5.0 mm, with the optimal thickness of 5.0 mm leading to the maximum increase (32.7%) in the damping ratio of concrete.


  • Open Access

    Evaluating the effectiveness of speed humps and rumble strips in improving pedestrian safety in Addis Ababa, Ethiopia

    by Getu Segni Tulu, Robert Tama Lisinge, Abrham Gebre Tarekegn, Tigist Eshetu

    Pedestrian fatalities remain a major road safety problem in Addis Ababa. To address this problem, speed humps and rumble strips were introduced on high-crash road segments in the city in 2017. As a case study that can be useful elsewhere, the aim of this research is to evaluate the effectiveness of speed hump with rumble strips in Addis Ababa. This study uses descriptive and inferential statistics to evaluate the impact of these interventions. Crash data between 2014 and 2021, excluding 2017 when the measures were implemented, is used in the analysis. The interventions led to a 25.08% reduction in operating speeds, with statistically significant speed reductions for passenger cars. Our findings on the extent to which speed humps and rumble strips lowered the speed of buses and trucks are not conclusive. Notable speed drops were observed at humps in some road segments while humps had no appreciable effect on speed in others. This underscores the need for additional measures or other approaches to reduce the operating speed of buses and trucks. The equivalent crash number for pedestrian crashes reduced by 24.45% and total crashes dropped by 51.14%. While crashes involving pedestrians crossing roads reduced, those involving pedestrians walking along travel lanes increased by 15.94%. These mixed results suggests that the effectiveness of speed humps and rumble strips depends on the type of crash being addressed and the category of vehicle involved.


  • Open Access

    Non-Destructive Testing Techniques for Condition Assessment of Concrete Structures: A Review

    by Belay Tefera, Abrham Tarekegn

    Non-destructive testing (NDT) techniques have developed as important instruments in the evaluation of concrete structures, providing a way to analyze structural integrity and material qualities without causing damage. In analyzing the uniformity, homogeneity, approximate compressive strength, durability, the level of rebar corrosion in concrete, and other properties of damaged buildings, NDT technologies have a significant benefit. This paper offers a thorough examination of several NDT methods, emphasizing their usefulness in finding internal flaws, locating embedded items, and measuring surface-hardness and in-situ stress. Each method's applicability, limitations, and measured parameters are thoroughly addressed. The criteria for selecting appropriate NDT methods are discussed, followed by a comparison of different approaches to facilitate decision-making. The interpretation of NDT results is discussed, highlighting the significance of precise data processing and the relevance of sophisticated technology. Case studies were also provided to demonstrate the actual implementation and efficacy of NDT techniques in real-world circumstances. The assessment also suggests investing in advanced data visualization tools to better the interpretation and sharing of NDT results, as well as combining NDT data with Building Information Modeling systems to provide a more complete picture of structural problems. Finally, the paper indicates that NDT techniques are critical for assuring the safety, durability, and preservation of concrete structures, thereby significantly contributing to the upkeep of our built environment.


  • Reliability Assessment of Cracked Reinforced Concrete Slab and Verification using a Full-Scale in-Situ Load Test

    by Yisihak Gebre Tarekegn, Biruktawit Taye Tarekegn, Abrham Gebre Tarekegn, Asmerom Abay

    This paper presents a case study focused on the deterministic and probabilistic structural assessments of a cracked reinforced concrete (RC) slab and evaluation using in-situ load testing. The case study explores the practical application of in-situ load testing as a diagnostic tool for evaluating the condition of the slab and determining its ultimate load-carrying capacity in the presence of cracks, and service loads are used to verify its serviceability. Through comprehensive analysis and interpretation of test results, this study aims to provide valuable insights into the structural performance of cracked reinforced concrete slabs and inform effective repair and rehabilitation strategies. The building under examination is a G+4 reinforced concrete structure constructed using ready mix concrete transported to the construction site. Upon inspecting the slab, which had a total thickness of 170 mm, numerous deeply mapped cracks were evident, visible from the slab's surface and extending through its entire depth. Structural analysis indicated that the design included sufficient reinforcement and that the loads acting upon the slab were not expected to induce the cracking. Factors such as poor construction practices, potential issues with the cement used, and excessive evaporation may have contributed to the occurrence of these cracks, necessitating repairs. A full-scale in-situ load test was performed following ACI 318-08 testing procedures and results show that the slab under investigation is reasonably safe against serviceability and strength requirements with “no evidence” of failure.