Jatoth Heeraman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jatoth Heeraman has a total of 77 co-authors. Here are the top co-authors by number of shared publications:
- Praveen Barmavatu
Departamento de Mecánica, Facultad de Ingeniería, Universidad Tecnológica Metropolitana, Santiago, Chile
8 shared publications Sonali Anant Deshmukh
Babasaheb Phadtare Engineering & Technology
6 shared publicationsPraveen Barmavatu
Departamento de Mecánica, Facultad de Ingeniería, Universidad Tecnológica Metropolitana, Ñuñoa, Chile
4 shared publicationsRamalinga Viswanathan Mangalaraja
Faculty of Engineering and Architecture, Universidad Arturo Prat, Iquique, Chile
4 shared publications- Bhumiswor Sharma
Tribhuvan University
3 shared publications Dadapeer Doddamani
Mechanical and Chemical Engineering Unit, University of Technology and Applied Sciences, Muscat, Sultanate of Oman
3 shared publications
Latest Publications
- 20 October 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Thermophysics and Heat Transfer
- p. 1-11
Artificial Neural Networks for Performance Prediction of CO2 Transcritical Heat Pump System
The rising global demand for energy-efficient heating systems has increased interest in [Formula: see text]-based transcritical heat pumps due to their unique thermodynamic behavior and environmental advantages. However, conventional models struggle with the nonlinear nature of transcritical cycles, and existing artificial neural network (ANN) approaches often fail to capture key interacting parameters under varying conditions. This study presents an advanced ANN-based model to accurately predict the performance of a [Formula: see text] transcritical heat pump, validated against experimental data. A feed-forward neural network is developed to analyze nonlinear system relationships using six input parameters: initial charge state, throttle valve opening, evaporator and gas cooler water flow rates, and their respective temperatures. Five performance metrics are predicted: coefficient of performance, cooling capacity, heating capacity, compressor work input, and discharge pressure. The model is trained and validated using experimental data from 36 operating conditions, with dataset size determined through statistical power analysis to prevent overfitting. High prediction accuracy is achieved, with [Formula: see text] values ranging from 0.956 to 0.986 and MSE between [Formula: see text] and [Formula: see text]. Compared to conventional methods, the ANN model is more accurate, efficient, and practical and can be extended to optimize and analyze various transcritical [Formula: see text] system configurations.
- 20 October 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Thermophysics and Heat Transfer
- p. 1-11
Artificial Neural Networks for Performance Prediction of CO2 Transcritical Heat Pump System
The rising global demand for energy-efficient heating systems has increased interest in [Formula: see text]-based transcritical heat pumps due to their unique thermodynamic behavior and environmental advantages. However, conventional models struggle with the nonlinear nature of transcritical cycles, and existing artificial neural network (ANN) approaches often fail to capture key interacting parameters under varying conditions. This study presents an advanced ANN-based model to accurately predict the performance of a [Formula: see text] transcritical heat pump, validated against experimental data. A feed-forward neural network is developed to analyze nonlinear system relationships using six input parameters: initial charge state, throttle valve opening, evaporator and gas cooler water flow rates, and their respective temperatures. Five performance metrics are predicted: coefficient of performance, cooling capacity, heating capacity, compressor work input, and discharge pressure. The model is trained and validated using experimental data from 36 operating conditions, with dataset size determined through statistical power analysis to prevent overfitting. High prediction accuracy is achieved, with [Formula: see text] values ranging from 0.956 to 0.986 and MSE between [Formula: see text] and [Formula: see text]. Compared to conventional methods, the ANN model is more accurate, efficient, and practical and can be extended to optimize and analyze various transcritical [Formula: see text] system configurations.
- Open Access
- 24 September 2026
- Published by Springer Nature in Discover Mechanical Engineering
- Vol. 5 (1) , 179
Exploring the thermofluidic performance of hybrid nanofluids under variable flow conditions in a controlled thermal channel
- 24 September 2026
- Published by Springer Nature in Discover Mechanical Engineering
- Vol. 5 (1) , 179
Open AccessExploring the thermofluidic performance of hybrid nanofluids under variable flow conditions in a controlled thermal channel
- 10 August 2026
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 20 (11) , 6705-6719
A hybrid lean design thinking framework for solving axis misalignment through fixture design
- 10 August 2026
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 20 (11) , 6705-6719
A hybrid lean design thinking framework for solving axis misalignment through fixture design
- 5 August 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (18) , 15519-15533
Experimental and optimization study on heat transfer in liquid jet impingement using particle swarm optimization for thermal management
- 5 August 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (18) , 15519-15533
Experimental and optimization study on heat transfer in liquid jet impingement using particle swarm optimization for thermal management
- 5 July 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Thermophysics and Heat Transfer
- p. 1-12
Computational and Experimental Analysis of Thermohydraulic Enhancement in Solar Air Heaters
A novel compound roughness configuration, consisting of repeated chamfer rib–semicircular groove elements, is proposed to enhance the thermohydraulic performance of solar air heaters. Computational fluid dynamics (CFD) simulations were performed to optimize key geometric parameters (which will break the viscous sublayer and enhance heat transfer), including roughness height, chamfer angle, groove position, and groove depth under turbulent flow conditions ([ ]). The geometry that has been taken for optimization is repeated chamfer rib–semicircular groove roughness. The groove position was optimized, and it is kept exactly at the reattachment point. Providing a semicircular groove instead of a V-groove resulted in greater heat transfer enhancement, as more turbulence is created. Also, it resulted in a lower friction factor. Thus, the performance index for the semicircular groove is higher than that for the V-groove. CFD investigations reported a heat transfer enhancement of 3.6-fold and a friction factor ratio of 2.4-fold, whereas experimental studies reported a heat transfer enhancement of 3.5-fold and a friction factor ratio of 3-fold. As per the experimental results, the performance index obtained is 2.5, which is high compared to those of other geometries.
- 5 July 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Thermophysics and Heat Transfer
- p. 1-12
Computational and Experimental Analysis of Thermohydraulic Enhancement in Solar Air Heaters
A novel compound roughness configuration, consisting of repeated chamfer rib–semicircular groove elements, is proposed to enhance the thermohydraulic performance of solar air heaters. Computational fluid dynamics (CFD) simulations were performed to optimize key geometric parameters (which will break the viscous sublayer and enhance heat transfer), including roughness height, chamfer angle, groove position, and groove depth under turbulent flow conditions ([ ]). The geometry that has been taken for optimization is repeated chamfer rib–semicircular groove roughness. The groove position was optimized, and it is kept exactly at the reattachment point. Providing a semicircular groove instead of a V-groove resulted in greater heat transfer enhancement, as more turbulence is created. Also, it resulted in a lower friction factor. Thus, the performance index for the semicircular groove is higher than that for the V-groove. CFD investigations reported a heat transfer enhancement of 3.6-fold and a friction factor ratio of 2.4-fold, whereas experimental studies reported a heat transfer enhancement of 3.5-fold and a friction factor ratio of 3-fold. As per the experimental results, the performance index obtained is 2.5, which is high compared to those of other geometries.
- Open Access
- 2 June 2026
- Published by Elsevier in Next Materials
- Vol. 12
Development and thermo-mechanical characterisation of NaOH-treated Palmyra fibre reinforced Kondagogu gum based sustainable biocomposites
- 2 June 2026
- Published by Elsevier in Next Materials
- Vol. 12
Open AccessDevelopment and thermo-mechanical characterisation of NaOH-treated Palmyra fibre reinforced Kondagogu gum based sustainable biocomposites
- 2 March 2026
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 45 (4)
Comprehensive environmental and economic analysis of active‐mode greenhouse solar dryers for green peas processing
In the natural drying, as the agro products are directly bare to the sun, nutrition's have been lost and the quality is spoiled by dust particles, insects etc. In this work to perform drying experiments on red chili and green peas, four greenhouse solar dryers are designed with two dissimilar roof shapes and cover materials. The roof shapes investigated are even span and parabolic and covering materials such as polyethylene and poly vinyl chloride sheets. All the four dryers consist of three layers as black painted plywood at the bottom, black PVC sheet of 3 mm thickness in the middle and the upper layer is prepared with Stainless Steel mesh tray which is used to place the product to be dried. To study the results with two different roofs shape and cover materials by using green peas. The outcomes show that humidity is reduced from 76% to 8%(wet basis) in the dryer of parabolic shape with polyethylene cover material within 20 solar hours whereas open sun drying requires 36 solar hours, hence it is efficient in saving the drying time of 44.4%. Thermal and environmental analyses are carried out to ensure the efficiency of the dryer and environmental impact. The net CO 2 mitigation was calculated to be 22.07 tons, and the generated carbon credit was calculated to be Rs. 21,006. The total quantity of dried green peas from each greenhouse solar dryer is estimated as 52 kg and reimbursement period for the parabolic polyethylene greenhouse solar dryer is 2 years.
- 2 March 2026
- Published by Wiley in Environmental Progress & Sustainable Energy
- Vol. 45 (4)
Comprehensive environmental and economic analysis of active‐mode greenhouse solar dryers for green peas processing
In the natural drying, as the agro products are directly bare to the sun, nutrition's have been lost and the quality is spoiled by dust particles, insects etc. In this work to perform drying experiments on red chili and green peas, four greenhouse solar dryers are designed with two dissimilar roof shapes and cover materials. The roof shapes investigated are even span and parabolic and covering materials such as polyethylene and poly vinyl chloride sheets. All the four dryers consist of three layers as black painted plywood at the bottom, black PVC sheet of 3 mm thickness in the middle and the upper layer is prepared with Stainless Steel mesh tray which is used to place the product to be dried. To study the results with two different roofs shape and cover materials by using green peas. The outcomes show that humidity is reduced from 76% to 8%(wet basis) in the dryer of parabolic shape with polyethylene cover material within 20 solar hours whereas open sun drying requires 36 solar hours, hence it is efficient in saving the drying time of 44.4%. Thermal and environmental analyses are carried out to ensure the efficiency of the dryer and environmental impact. The net CO 2 mitigation was calculated to be 22.07 tons, and the generated carbon credit was calculated to be Rs. 21,006. The total quantity of dried green peas from each greenhouse solar dryer is estimated as 52 kg and reimbursement period for the parabolic polyethylene greenhouse solar dryer is 2 years.
- 19 February 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (6) , 4957-4972
Enhancing heat transfer efficiency: a thorough review on liquid jet impingement, nozzle inclination, and separation
- 19 February 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (6) , 4957-4972
Enhancing heat transfer efficiency: a thorough review on liquid jet impingement, nozzle inclination, and separation
- 4 February 2026
- Published by Taylor & Francis
- p. 1-22
Introduction to Heat Transfer in Sustainable Energy Systems
- 4 February 2026
- Published by Taylor & Francis
- p. 1-22
Introduction to Heat Transfer in Sustainable Energy Systems