Wang ZhiJie
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wang ZhiJie has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
C.L. Zhang
Freescale Inc
1 shared publicationCuckoo Du
Freescale Inc. Tianjin China
1 shared publicationM.C. Han
Freescale Inc. Tianjin China
1 shared publicationPeline Cao
Freescale Inc
1 shared publicationSuYing Yao
Institute of Electronics & Information Engineering, Tianjin University, Tianjin 300381, China
1 shared publicationVito Huang
Freescale Inc
1 shared publication
Latest Publications
- 1 August 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Cu low k device wire bonding process modeling
As semiconductor industry reaches 90 nm technology node and below, Cu low k technology has been widely used in integrated circuits to further reduce RC delay and power dissipation. Due to the intrinsic properties of low K material (poor adhesion with metal layer, lower modulus and higher CTE), wire bond process window gets narrowed. Crack/peeling between low k ILD layer and metal (barrier) layer are common wire bond defects which cause both packaging manufacturability and product reliability issues. In this paper, physical and mathematical models of wire bonding process were established. The regression equation of impact force and C/V (contact velocity) was obtained through simulation and actual wire bonding data. A Cu low k CMOS 90 nm test vehicle was chosen for the modeling. The bonding impact load curve was obtained through the regression of modeling and actual bonding response. The effect of impact force on the formation of smashed ball as well as the mechanical deformation imposed to the bond pad was studied. Through simulation, capillary dimension - ICA (inner chamfer angle) was found critical to achieve 25% BBR (ball height to ball size ratio) with 40 um BPO (bond pad opening) which is important for consistent IMC formation and stronger IMC integrity over heat excursion. Through the bond pad deformation simulation under different metal structure design, it is found local low K dielectric design can effectively reduce the bond pad deformation & cupping, thus widen the wire bond process window.
- 1 August 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Cu low k device wire bonding process modeling
As semiconductor industry reaches 90 nm technology node and below, Cu low k technology has been widely used in integrated circuits to further reduce RC delay and power dissipation. Due to the intrinsic properties of low K material (poor adhesion with metal layer, lower modulus and higher CTE), wire bond process window gets narrowed. Crack/peeling between low k ILD layer and metal (barrier) layer are common wire bond defects which cause both packaging manufacturability and product reliability issues. In this paper, physical and mathematical models of wire bonding process were established. The regression equation of impact force and C/V (contact velocity) was obtained through simulation and actual wire bonding data. A Cu low k CMOS 90 nm test vehicle was chosen for the modeling. The bonding impact load curve was obtained through the regression of modeling and actual bonding response. The effect of impact force on the formation of smashed ball as well as the mechanical deformation imposed to the bond pad was studied. Through simulation, capillary dimension - ICA (inner chamfer angle) was found critical to achieve 25% BBR (ball height to ball size ratio) with 40 um BPO (bond pad opening) which is important for consistent IMC formation and stronger IMC integrity over heat excursion. Through the bond pad deformation simulation under different metal structure design, it is found local low K dielectric design can effectively reduce the bond pad deformation & cupping, thus widen the wire bond process window.
- 1 June 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
BGA 44um Fine Pitch Low K Wire Bonding Process Development
With the further shrink of the IC dimension, the low K material has been widely used to replace the traditional SiO2 ILD in order to reduce the interconnect delay, the introduction of low k material into silicon imposed challenges on assembly wire bonding process which is further magnified with the shrink of the bond pad. In this paper, 44um fine pitch CMOS90 nm low k device is chosen to develop the wire bond process capability on BGA package. The low k material structure and its impact on fine pitch wire bonding are introduced, the critical factors (wire type, bonding tool, bonding equipment and bonding parameters) and critical responses Ball size, Ball height / Bonded ball diameter ratio, bond placement, wire pull and ball shear) affecting 44um fine pitch low k wire bonding quality and manufacturability were explored, DOE (design of Experiment) was used to optimize the wire bond process, thermal aging test coupled with wire pull/ ball shear test and their corresponding failure mode was studied. The IMC (Inter Metallic coverage) of the Au-Al was addressed also. The optimized process window/ recipe passed package reliability test with 44um fine pitch C90 low K device.
- 1 June 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
BGA 44um Fine Pitch Low K Wire Bonding Process Development
With the further shrink of the IC dimension, the low K material has been widely used to replace the traditional SiO2 ILD in order to reduce the interconnect delay, the introduction of low k material into silicon imposed challenges on assembly wire bonding process which is further magnified with the shrink of the bond pad. In this paper, 44um fine pitch CMOS90 nm low k device is chosen to develop the wire bond process capability on BGA package. The low k material structure and its impact on fine pitch wire bonding are introduced, the critical factors (wire type, bonding tool, bonding equipment and bonding parameters) and critical responses Ball size, Ball height / Bonded ball diameter ratio, bond placement, wire pull and ball shear) affecting 44um fine pitch low k wire bonding quality and manufacturability were explored, DOE (design of Experiment) was used to optimize the wire bond process, thermal aging test coupled with wire pull/ ball shear test and their corresponding failure mode was studied. The IMC (Inter Metallic coverage) of the Au-Al was addressed also. The optimized process window/ recipe passed package reliability test with 44um fine pitch C90 low K device.