Dongryul Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dongryul Lee has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Jihyun Kim
Department of Chemical and Biological Engineering, Seoul National University, Seoul 08826, Republic of Korea
4 shared publications Jihyun Kim
Seoul National University
3 shared publications- Woong Choi
Department of Chemical and Biological Engineering, Seoul National University, Seoul 08826, Republic of Korea
3 shared publications - Donggyu Lee
Department of Chemical and Biological Engineering, Seoul National University 1 , Seoul 08826
2 shared publications - Jungbae Kim
Korea University
2 shared publications Dae-Woo Jeon
Korea Institute of Ceramic Engineering and Technology, Jinju 52851, South Korea
1 shared publication
Latest Publications
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (34) , 1593
(Invited) From Plasma-Functionalized CNTs to Photonics and Plasma-Engineered 2D pH Sensor Platforms: Evolution of Surface-Engineered Solid-State Biosensing
As biosensing platforms based on solid-state electronics continue to evolve toward higher sensitivity, selectivity, and integration density, material-level innovation and surface functionalization have emerged as defining technological requirements. Until the early 2020s, carbon nanotubes (CNTs), graphene, nanomaterials, and metal nanoparticles have been extensively explored as promising signal and enzyme transducers due to their excellent electrical conductivity and large specific surface area. However, for practical biosensing applications, room-temperature process strategies that simultaneously enhance surface reactivity and enzyme loading while preserving or improving electrical transport properties remain insufficiently developed. In particular, CNT functionalization has often relied on high-temperature thermal treatments or high-energy chemical processes, resulting in limited efficiency relative to resource input and inherent constraints in improving loading capacity and sensing sensitivity.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (34) , 1593
(Invited) From Plasma-Functionalized CNTs to Photonics and Plasma-Engineered 2D pH Sensor Platforms: Evolution of Surface-Engineered Solid-State Biosensing
As biosensing platforms based on solid-state electronics continue to evolve toward higher sensitivity, selectivity, and integration density, material-level innovation and surface functionalization have emerged as defining technological requirements. Until the early 2020s, carbon nanotubes (CNTs), graphene, nanomaterials, and metal nanoparticles have been extensively explored as promising signal and enzyme transducers due to their excellent electrical conductivity and large specific surface area. However, for practical biosensing applications, room-temperature process strategies that simultaneously enhance surface reactivity and enzyme loading while preserving or improving electrical transport properties remain insufficiently developed. In particular, CNT functionalization has often relied on high-temperature thermal treatments or high-energy chemical processes, resulting in limited efficiency relative to resource input and inherent constraints in improving loading capacity and sensing sensitivity.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (33) , 1498
Junction-All-Around WSe2/β-Ga2O3 p-n Heterojunction Transistor with Ultra-High Mobility Enabling NDR-Based Multilevel Logic and Memory
β-gallium oxide (β-Ga2O3) has attracted significant attention as a next-generation wide-bandgap semiconductor owing to its ultra-wide bandgap (4.9 eV) and strong potential to overcome the intrinsic limitations of silicon (Si) in high-power and high-frequency electronics. With the rapid expansion of artificial intelligence (AI) and high-performance computing systems, there is an urgent demand for semiconductor platforms capable of sustaining high power density and fast switching operation, while simultaneously supporting increasingly complex computing paradigms beyond conventional Boolean logic, such as energy-efficient process-in-memory (PIM) architectures that integrate logic and memory within a single platform. While conventional Si-based devices are fundamentally limited by their low on/off ratio and mobility constraints, β-Ga2O3 offers a promising alternative in terms of operational robustness and power handling capability. Nevertheless, the inherently low field-effect mobility of β-Ga2O3—typically on the order of ~20 cm2/V∙s in conventional transistor architectures—remains a critical bottleneck, restricting both high-speed switching and the realization of advanced AI-oriented computing functionalities.
- 7 July 2026
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2026-01 (33) , 1498
Junction-All-Around WSe2/β-Ga2O3 p-n Heterojunction Transistor with Ultra-High Mobility Enabling NDR-Based Multilevel Logic and Memory
β-gallium oxide (β-Ga2O3) has attracted significant attention as a next-generation wide-bandgap semiconductor owing to its ultra-wide bandgap (4.9 eV) and strong potential to overcome the intrinsic limitations of silicon (Si) in high-power and high-frequency electronics. With the rapid expansion of artificial intelligence (AI) and high-performance computing systems, there is an urgent demand for semiconductor platforms capable of sustaining high power density and fast switching operation, while simultaneously supporting increasingly complex computing paradigms beyond conventional Boolean logic, such as energy-efficient process-in-memory (PIM) architectures that integrate logic and memory within a single platform. While conventional Si-based devices are fundamentally limited by their low on/off ratio and mobility constraints, β-Ga2O3 offers a promising alternative in terms of operational robustness and power handling capability. Nevertheless, the inherently low field-effect mobility of β-Ga2O3—typically on the order of ~20 cm2/V∙s in conventional transistor architectures—remains a critical bottleneck, restricting both high-speed switching and the realization of advanced AI-oriented computing functionalities.
- 3 May 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 13 (21) , 10561-10566
Annealing-free Ohmic contact of β-Ga 2 O 3 via nitrogen plasma treatment
High-quality Ohmic contact was achieved via direct nitrogen plasma treatment, significantly enhancing β-Ga 2 O 3 mobility (76 cm 2 V −1 s −1 ) and on/off ratio (1.7 × 10 10 ), demonstrating strong potential for future ultra-scaled integrated circuits.
- 3 May 2025
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 13 (21) , 10561-10566
Annealing-free Ohmic contact of β-Ga 2 O 3 via nitrogen plasma treatment
High-quality Ohmic contact was achieved via direct nitrogen plasma treatment, significantly enhancing β-Ga 2 O 3 mobility (76 cm 2 V −1 s −1 ) and on/off ratio (1.7 × 10 10 ), demonstrating strong potential for future ultra-scaled integrated circuits.
- 18 April 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (17) , 25500-25506
Mixed-Dimensional Contact Architecture to WSe2 for Efficient Hole Injection
Si-based electronic devices face inherent performance limitations at the nanoscale, primarily due to short-channel effects and interface defects. As a result, transition-metal dichalcogenides (TMDs) have emerged as promising alternatives, offering unique advantages such as dangling-bond-free surfaces and tunable bandgaps. Among TMDs, tungsten diselenide (WSe2) has garnered significant attention as a p-type semiconductor owing to its high hole mobility and favorable surface chemistry. However, its practical implementation is often hindered by Fermi-level pinning at metal contacts, leading to high contact resistance and limited carrier injection efficiency. In this study, we present a mixed-dimensional contact architecture that integrates one-dimensional (1D) edge contacts and two-dimensional (2D) surface contacts to enhance hole injection in WSe2 field-effect transistors (FETs). By controlling the ratio of the 1D/2D contact architecture, the optimal edge/surface contact ratio from the fabricated WSe2 FET was obtained when the ratio 1D-length/2D-area = 0.26, exhibiting high field-effect hole mobility (171 cm2/V·s) and low specific contact resistance (2.97 kΩ·μm). Ultraviolet/ozone treatment was employed to form tungsten oxide uniformly at the contact regions, facilitating hole doping and thereby reducing contact resistance. The fabricated WSe2 FETs demonstrated a high current on/off ratio of 5 × 108 and excellent Ohmic contact behavior, with an extracted Schottky barrier height of 0.09 eV. These findings feature the effectiveness of the mixed-dimensional contact architecture in optimizing carrier injection and overcoming the challenges associated with conventional contact schemes. By utilizing the complementary benefits of edge and surface contacts, this approach offers a promising strategy for achieving high-performance TMD-based complementary metal-oxide-semiconductor devices, paving the way for next-generation atomically thin electronic applications.
- 18 April 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (17) , 25500-25506
Mixed-Dimensional Contact Architecture to WSe2 for Efficient Hole Injection
Si-based electronic devices face inherent performance limitations at the nanoscale, primarily due to short-channel effects and interface defects. As a result, transition-metal dichalcogenides (TMDs) have emerged as promising alternatives, offering unique advantages such as dangling-bond-free surfaces and tunable bandgaps. Among TMDs, tungsten diselenide (WSe2) has garnered significant attention as a p-type semiconductor owing to its high hole mobility and favorable surface chemistry. However, its practical implementation is often hindered by Fermi-level pinning at metal contacts, leading to high contact resistance and limited carrier injection efficiency. In this study, we present a mixed-dimensional contact architecture that integrates one-dimensional (1D) edge contacts and two-dimensional (2D) surface contacts to enhance hole injection in WSe2 field-effect transistors (FETs). By controlling the ratio of the 1D/2D contact architecture, the optimal edge/surface contact ratio from the fabricated WSe2 FET was obtained when the ratio 1D-length/2D-area = 0.26, exhibiting high field-effect hole mobility (171 cm2/V·s) and low specific contact resistance (2.97 kΩ·μm). Ultraviolet/ozone treatment was employed to form tungsten oxide uniformly at the contact regions, facilitating hole doping and thereby reducing contact resistance. The fabricated WSe2 FETs demonstrated a high current on/off ratio of 5 × 108 and excellent Ohmic contact behavior, with an extracted Schottky barrier height of 0.09 eV. These findings feature the effectiveness of the mixed-dimensional contact architecture in optimizing carrier injection and overcoming the challenges associated with conventional contact schemes. By utilizing the complementary benefits of edge and surface contacts, this approach offers a promising strategy for achieving high-performance TMD-based complementary metal-oxide-semiconductor devices, paving the way for next-generation atomically thin electronic applications.
- Open Access
- 5 September 2023
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 4 (19) , 4520-4527
Photo-enhanced metal-assisted chemical etching of α-gallium oxide grown by halide vapor-phase epitaxy on a sapphire substrate and its applications
Our study presents photo-enhanced metal-assisted chemical etching of α-Ga2O3 and its properties at various temperatures. The results show great potential for use in α-Ga2O3-based optoelectronic device fabrication.
- 5 September 2023
- Published by Royal Society of Chemistry (RSC) in Materials Advances
- Vol. 4 (19) , 4520-4527
Open AccessPhoto-enhanced metal-assisted chemical etching of α-gallium oxide grown by halide vapor-phase epitaxy on a sapphire substrate and its applications
Our study presents photo-enhanced metal-assisted chemical etching of α-Ga2O3 and its properties at various temperatures. The results show great potential for use in α-Ga2O3-based optoelectronic device fabrication.
- 1 May 2023
- Published by Elsevier in Applied Surface Science
- Vol. 628
Damage-free remote SF6 plasma-treated CNTs for facile fabrication of electrochemical enzyme biosensors
- 1 May 2023
- Published by Elsevier in Applied Surface Science
- Vol. 628
Damage-free remote SF6 plasma-treated CNTs for facile fabrication of electrochemical enzyme biosensors