E. A. Pupysheva
Research Subjects
E. A. Pupysheva has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
- Elmira Fedorova
Saint-Petersburg Mining University, 2, 21st line, Saint-Petersburg, 199106, Russia
2 shared publications - Vladimir Morgunov
Department of Mineral Processing, Automation of Technological Processes and Production, Empress Catherine II St. Petersburg Mining University, 199106 St. Petersburg, Russia
2 shared publications
Latest Publications
- 30 June 2024
- Published by Ore and Metals Publishing House in Non-ferrous Metals
- No. 1,p. 28-34
Effect of variation of internal diameter along the length of a rotary kiln on material movement
Tubular rotary kilns are actively used in non-ferrous metallurgy, for example for sintering nepheline with limestone in alumina production. For the most effective heat exchange due to good mixing of the material in rotary kilns, a rolling regime characterized by the presence of an active layer and a stagnant area is maintained. Also the problem of formation of coating layers inside the kiln, which leads to a narrowing of the inner diameter of the aggregate, is known. In this paper, using the DEM-modeling method the influence of limes on the active layer parameters: the average speed of particles in the active layer and the share of the active layer in the aggregate at different rotational speeds and the degree of filling of the drum. With the increase of the coating layers thickness the average speed of particles in the active layer and the proportion of particles in the active layer in the entire profile of the kiln increases, changes in the shape of the profile of the speed of particles in the active layer and the proportion of particles in the active layer, depending on the thickness of coating layers are observed. The obtained conclusions are of qualitative nature and indicate a significant influence of the coating layers thickness on the active layer parameters and the need for further study of this process on the physical model with the real charge material.
- 30 June 2024
- Published by Ore and Metals Publishing House in Non-ferrous Metals
- No. 1,p. 28-34
Effect of variation of internal diameter along the length of a rotary kiln on material movement
Tubular rotary kilns are actively used in non-ferrous metallurgy, for example for sintering nepheline with limestone in alumina production. For the most effective heat exchange due to good mixing of the material in rotary kilns, a rolling regime characterized by the presence of an active layer and a stagnant area is maintained. Also the problem of formation of coating layers inside the kiln, which leads to a narrowing of the inner diameter of the aggregate, is known. In this paper, using the DEM-modeling method the influence of limes on the active layer parameters: the average speed of particles in the active layer and the share of the active layer in the aggregate at different rotational speeds and the degree of filling of the drum. With the increase of the coating layers thickness the average speed of particles in the active layer and the proportion of particles in the active layer in the entire profile of the kiln increases, changes in the shape of the profile of the speed of particles in the active layer and the proportion of particles in the active layer, depending on the thickness of coating layers are observed. The obtained conclusions are of qualitative nature and indicate a significant influence of the coating layers thickness on the active layer parameters and the need for further study of this process on the physical model with the real charge material.
- 28 April 2023
- Published by Ore and Metals Publishing House in Tsvetnye Metally
- No. 4,p. 77-84
Settling parameters determined during thickening and washing of red muds
This paper substantiates why it is necessary to reduce the concentration of sodium hydroxide in red mud before it can be transported to the mud disposal area and why the liquid-to-solid ratio should be maintained after each unit of the thickening and washing line. The main unit is a single-tier radial thickener comprised of flocculation, free settling, hindered settling and rake zones. The paper gives a brief overview of the basic mathematical formulas describing the hindered and free settling zones of the thickener, as well as the basic material balance equations for describing the countercurrent washers. At the studied site, no reagent is added at the washing stage and there is no flocculation zone in the washers. The first part of experimental study focused on red mud thickening with addition of dissolved flocculant that is normally used at the studied site, considering how it is prepared and injected. Sedimentation curves for red mud samples with different concentrations of solids in the feed stream were obtained. The authors substantiate the application of modified Kynch method for calculating empirical parameters based on sedimentation curves. The following parameters were calculated: settling rate, average Stokes diameter of a flocculated particle, critical concentration (gel point), hindered settling index. The Kynch flux density functions were calculated for different concentrations of solids in the initial slurry. The second part of experimental study focused on countercurrent washing of the earlier flocculated slurry. Following a series of periodic experiments on sedimentation of flocculated slurry involving 3, 4, 5 and 6 cycles of countercurrent washing, conclusions were drawn on the concentration of sodium hydroxide at each washing stage, and the washing efficiency was estimated. The described results will be used for building a mathematical model of a radial thickener at the thickening and washing stage.
- 28 April 2023
- Published by Ore and Metals Publishing House in Tsvetnye Metally
- No. 4,p. 77-84
Settling parameters determined during thickening and washing of red muds
This paper substantiates why it is necessary to reduce the concentration of sodium hydroxide in red mud before it can be transported to the mud disposal area and why the liquid-to-solid ratio should be maintained after each unit of the thickening and washing line. The main unit is a single-tier radial thickener comprised of flocculation, free settling, hindered settling and rake zones. The paper gives a brief overview of the basic mathematical formulas describing the hindered and free settling zones of the thickener, as well as the basic material balance equations for describing the countercurrent washers. At the studied site, no reagent is added at the washing stage and there is no flocculation zone in the washers. The first part of experimental study focused on red mud thickening with addition of dissolved flocculant that is normally used at the studied site, considering how it is prepared and injected. Sedimentation curves for red mud samples with different concentrations of solids in the feed stream were obtained. The authors substantiate the application of modified Kynch method for calculating empirical parameters based on sedimentation curves. The following parameters were calculated: settling rate, average Stokes diameter of a flocculated particle, critical concentration (gel point), hindered settling index. The Kynch flux density functions were calculated for different concentrations of solids in the initial slurry. The second part of experimental study focused on countercurrent washing of the earlier flocculated slurry. Following a series of periodic experiments on sedimentation of flocculated slurry involving 3, 4, 5 and 6 cycles of countercurrent washing, conclusions were drawn on the concentration of sodium hydroxide at each washing stage, and the washing efficiency was estimated. The described results will be used for building a mathematical model of a radial thickener at the thickening and washing stage.