EMElena Fernandez Mora

Elena Fernandez Mora

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Elena Fernandez Mora has a total of 51 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    High Field Cos-Theta FalconD-C Dipole Magnet Development at CERN

    by Arnaud Foussat, Nicola Sala, Sachin Gowrishankar, Juan Carlos Perez, Ariel Haziot, Carlos Fernandes, Lucio Fiscarelli, Mariusz Wozniak, Emmanuele Ravaioli, Oussama Id’BAhmane, et al.

    The FalconD (Future Accelerator post-LHC Cos-$\theta$ Optimized ${\mathrm{Nb}}_{3}$Sn Dipole magnet is part of the High Field Magnet (HFM) CERN programme. In collaboration with the Italian Institute for Nuclear Physics (INFN Genova and LASA Milano), CERN is developing a ${\cos \theta }$ dipole magnet beyond 12 T based on proven ${\mathrm{Nb}}_{3}$Sn technology in the MQXF quadrupole used in the high-luminosity upgrade of the LHC. The magnet, with design aperture diameter of 50 mm, provides a bore field of 12 T for a 73 TeV center-of-mass energy scenario for the Future FCC-hh Circular Collider. The project has specific objectives to investigate cos-$\theta$ short magnet model design based on a two-layers coil with a wide high current cable. Moreover, the study of mechanical dipole structures based on aluminum shell with bladders and key (B&K) developed for the HL-LHC MQXF quadrupole will be presented as a baseline. The structure pre-loading system assembly baseline shall be tested on sub-scale mechanical mock ups at 77 K prior to building two single aperture 1.5 m long ${\mathrm{Nb}}_{3}$Sn magnet models followed by a 2-in-1 dipole magnet assembly. In this paper, we provide an overview of the magnetic and structural design carried out at CERN on an increased aperture diameter variant supported by first preliminary winding trials and give insights of the project timeline. Some preliminary protection scheme assessment is presented as baseline to be tested. Following the cable winding outcomes and the mechanical properties measured, some alternative coil optimized magnetic cross-section is reported.


  • Conceptual Design of BOND: A 14 T Dipole for FCC-Hh

    by Juan Carlos Perez, Gloria Bellini, Elena Fernandez Mora, Jose Ferradas Troitino, Ariel Haziot, Susana Izquierdo Bermudez, Ezio Todesco

    High Field Nb$_{3}$Sn superconducting magnets are a core technology to increase the collision energy of particle accelerators beyond that of the Large Hadron Collider (LHC). In the framework of the conceptual design of a Future Circular Collider (FCC), or an energy upgrade of the LHC, different magnet layouts are being considered within the so-called High Field Magnet program. The target for all these designs is to provide a dipole field of ${\text{{14}}} \,\text{T}$ in a ${\text{50}} \,{\text{mm}}$ aperture. Cos-theta, block-type and common-coil magnets are explored. Following the successful test of the Racetrack Model Magnet (RMM) at CERN, which reached 16.5 T in a ${\text{50}} \,{\text{mm}}$ closed cavity, this paper details a block-type design made of 2 double-layers coils with flared-ends. The key challenges are addressed to provide an attractive solution for an accelerator type dipole aiming at a short-sample limit of ${\text{{18}}} \,\text{T}$ using available Nb$_{3}$Sn strand. A detailed 2D electromagnetic and mechanical analysis is presented for a single aperture demonstrator. In addition, the preliminary electromagnetic optimization for the final double aperture magnet is introduced.


  • Open Access

    Longitudinal and Transverse Dimensional Changes During Heat Treatment of the Nb3Sn Cables for the Graded Research Racetrack Dipole Demonstrator (R2D2)

    by E. Fernandez Mora, M. Durante, J. C. Perez, E. Rochepault, F. Rondeaux

    The Research Racetrack Dipole Demonstrator (R2D2) is a Nb 3 Sn graded magnet developed in the framework of the CEA-CERN collaboration with the goal to assess key technologies for future high field accelerator magnets. This demonstrator magnet features two 1.7 m long racetrack coils, designed in the graded configuration needed for compact and efficient high field magnets. Each coil is made of two different Nb 3 Sn cables wound around each other and submitted together to the high temperature heat treatment needed for Nb 3 Sn compound formation. The experience on Nb 3 Sn coils has taught us that the management of the deformations undergone by the Nb 3 Sn cable during its formation must be a priority in the definition and the dimensioning of the tools and the manufacturing processes of the coils. This paper reports the results of the test campaigns carried out at CEA Saclay to study the behavior of R2D2 cables during heat treatment. The first campaign consisted of reduced-coils made of a few turns of each cable, with representative lengths. For each coil, the winding is performed with gaps in the components, and the gaps are measured before and after the heat treatment to quantify the coil length variations. A second campaign consisted in measuring the thickness variations of cable stacks in various configurations. The results allowed validating the choices made for the final R2D2 coils and heat treatment tooling to manage the longitudinal contraction and the transverse expansion.


  • Mechanical Design of the Superconducting Magnet for the 28 GHz ECR Ion Source ASTERICS

    by T. Cadoux, N. Bakon, C. Berriaud, H. Felice, E. Fernandez Mora, P. Graffin, T. Guillo, G. Minier, F. Nunio, E. Rochepault, et al.

    ASTERICS is an Electron Cyclotron Resonance (ECR) ion source designed by CEA, GANIL, and LPSC for the NEWGAIN project in France. The design of the Nb-Ti superconducting magnet is inspired from two magnets built for 28 GHz ion sources (VENUS and FRIB ion sources) and is composed of a sextupole inside three solenoids to confine the plasma. The main improvement in terms of magnetic design comes from an increase of the plasma chamber radius from 71.85 mm to 91 mm aiming at increasing the metallic beam yield at both 18 and 28 GHz. This change in magnetic design leads to an increase of Lorentz forces, impacting the design of the mechanical structure. Like the FRIB ion source, the architecture uses an aluminum shell-based support structure with bladders and keys to compress the sextupole azimuthally, and endplates for its axial compression. The bladders and keys allow a disassembly of the sextupole coils, and an adjustment of the coils pre-stress. The solenoids are wound under tension around an aluminum mandrel acting as a shell for the sextupole pre-load. Interfaces between solenoids and mandrel are designed to allow detachment and low friction sliding during excitation. The scale-up of the support structure, to address the dimension increase, is presented here. The 2D and 3D mechanical models developed to perform the mechanical analysis and the results obtained are detailed along with the preliminary assembly process.


  • Progress in the Design of the ASTERICS 28 GHz ECR Ion Source Superconducting Magnet for the NEWGAIN Project at GANIL

    by D. Simon, H. Felice, H. Allain, N. Bakon, C. Berriaud, T. Cadoux, P. De Antoni, E. Fernandez Mora, T. Genestier, P. Graffin, et al.

    In the framework of the NEWGAIN project (NEW GAnil INjector), a new injector is under development to supply the SPIRAL2 LINAC at GANIL with heavy ion of a mass to charge-state ratio up to A/q = 7. In order to produce this heavy ion beam, a superconducting 28 GHz ECR Ion Source called ASTERICS is under development and its superconducting magnet used for plasma confinement is designed at CEA in collaboration with LPSC and GANIL. The magnetic design of the ion source is based on the well-proved sextupole-in-solenoids configuration used in different laboratories worldwide. The superconducting coils will be in Nb-Ti placed in a He bath cooled by 6 in-situ cryocoolers. A magnetic and protection optimization has been done to meet the NEWGAIN requirements which calls for a bigger plasma chamber than the existing superconducting ECR ion sources while maintaining the same temperature margin in the coils. This paper focuses on the magnetic analysis, the protection studies and the choice of the superconducting conductor for the sextupole and the solenoids. To validate the coil fabrication steps and the assumptions made in the magnetic design, some winding trials have been done. Both simulations and mock-up results are presented here.


  • Design of ASTERICS: A Superconducting 28 GHz ECR Ion Source Magnet for GANIL

    by D. Simon, T. Cadoux, E. Fernandez Mora, B. Hervieu, C. Berriaud, M. Segreti, G. Minier, E. Rochepault, R. Vallcorba, A. Sinanna, et al.

    In the framework of the NEWGAIN project, which aims to build a second injector with a mass to charge-state ratio A/q=7 for the SPIRAL2 linear accelerator at GANIL, CEA is developing in collaboration with LPSC and GANIL a new superconducting 28 GHz ECR Ion Source Magnet named ASTERICS. The magnetic design is based on an advanced concept of the VENUS ECR ion source operating at Berkeley and the FRIB source under commisionning at MSU. The ion source superconducting magnet consists of a sextupole inside three solenoids to confine the plasma and a shell-based support structure to apply a preload to the sextupole coils. The confinement coils will be made in Nb-Ti and will be operated at 4.2 K. The cryogenic environment will be ensured by liquid helium thermosiphon closed loop thanks to six in-situ cryocoolers. Specific HTS current leads are being designed to power the magnet. A cold integrated He buffer will also allow He almost-lossless quenches. The preliminary design choices of the ASTERICS superconducting magnet are presented here from the magnetic, mechanical and protection design to the cryogenic definition emphasizing the global approach used to obtain the final magnet configuration.