Hao Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hao Liu has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Guoqing Li
Key Laboratory of Light-Duty Gas-Turbine, Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190, China
3 shared publications - Xingen Lu
Key Laboratory of Light-Duty Gas-Turbine, Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190, China
3 shared publications - Ang Li
Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190, China; Beijing 100049, China
2 shared publications - Hui Li
Chinese Academy of Sciences Key Laboratory of Light-Duty Gas-Turbine, Institute of Engineering Thermophysics Beijing 100190 , China
2 shared publications Chenyang Kang
Key Laboratory of Light-duty Gas-turbine, Institute of Engineering Thermophysics, Chinese Academy of Sciences , Beijing 100190, China ; , Beijing 100049, China ; , Beijing 100190, China
1 shared publicationRuofan Wang
Key Laboratory of Light-duty Gas-turbine, Institute of Engineering Thermophysics, Chinese Academy of Sciences , Beijing 100190, China ; , Beijing 100049, China ; , Beijing 100190, China
1 shared publication
Latest Publications
- 3 October 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (3) , 1-37
Optimization of Smooth Straight-Through Labyrinth Seal Based on XGBoost and Improved Genetic Algorithm
Improving the sealing performance of labyrinth seal is beneficial in reducing the loss of downstream components as well as improving the aero-engines' efficiency. Meanwhile, the optimization of labyrinth seal is more cost-effective than optimizing other components of aero-engines. Based on extreme gradient boosting (XGBoost) and improved genetic algorithm (GA), an automatic optimizer for smooth straight-through labyrinth seal is proposed. According to the ordering of feature importance, the ten selected geometric parameters of smooth straight-through labyrinth seals with two gaps (0.1 mm, 0.25 mm) are optimized when the axial length of labyrinth seal is limited. The optimization results show that the leakage rate of the optimized labyrinth seal with two gaps is 19.67% and 23.80% lower than the reference labyrinth seal, respectively. It is found that the decrease of fin height, fin angle, fillet radius, and fin width, and the increase of fin pitch are beneficial to improve the sealing performance of smooth straight-through labyrinth seal. The analysis of flow field reveals the reasons for the improvement of sealing performance due to the change of geometric parameters. However, it must be noted that the optimization effect decreases as the pressure ratio increases, primarily as the result of the increase in carry-over coefficient. This work provides a new approach to optimize smooth straight-through labyrinth seal.
- 3 October 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (3) , 1-37
Optimization of Smooth Straight-Through Labyrinth Seal Based on XGBoost and Improved Genetic Algorithm
Improving the sealing performance of labyrinth seal is beneficial in reducing the loss of downstream components as well as improving the aero-engines' efficiency. Meanwhile, the optimization of labyrinth seal is more cost-effective than optimizing other components of aero-engines. Based on extreme gradient boosting (XGBoost) and improved genetic algorithm (GA), an automatic optimizer for smooth straight-through labyrinth seal is proposed. According to the ordering of feature importance, the ten selected geometric parameters of smooth straight-through labyrinth seals with two gaps (0.1 mm, 0.25 mm) are optimized when the axial length of labyrinth seal is limited. The optimization results show that the leakage rate of the optimized labyrinth seal with two gaps is 19.67% and 23.80% lower than the reference labyrinth seal, respectively. It is found that the decrease of fin height, fin angle, fillet radius, and fin width, and the increase of fin pitch are beneficial to improve the sealing performance of smooth straight-through labyrinth seal. The analysis of flow field reveals the reasons for the improvement of sealing performance due to the change of geometric parameters. However, it must be noted that the optimization effect decreases as the pressure ratio increases, primarily as the result of the increase in carry-over coefficient. This work provides a new approach to optimize smooth straight-through labyrinth seal.
- 2 November 2023
- Published by ASME International in Journal of Tribology
- Vol. 146 (2) , 1-43
Evolution and Action Mechanism of Relative Negative Pressure Zone in Spiral Groove Gas Face Seal for Aero-Engine
As an advanced sealing technology, the application of gas face seal in aero-engine is few; if possible, lower specific fuel consumption, higher thrust-weight ratio, and effective secondary flow control at minimal cost would be brought. A relative negative pressure zone (RNPZ) was found in the spiral groove gas face seal, and the evolution and action mechanism of RNPZ was investigated in detail, which may promote the above application. Three film thicknesses of spiral groove gas face seals at different rotational speeds and inlet pressures were numerically compared to obtain the pressure field in the groove area and the formation of RNPZ. Then, the radial and circumferential velocities in the groove were calculated to quantify the impact of the obstruction effect, viscous pumping, and shear effect, which revealed the evolution mechanism of the RNPZ stage by stage. At last, the action mechanism of RNPZ was clarified through the hydrodynamic performance analysis. It is found that the pressure field evolution in the gas face seal is in stage Ⅲ under the high rotational speed and low inlet pressure conditions in an aero-engine. Under the same film thickness, RNPZ can suppress leakage to a certain extent in stage Ⅱ, while in stage Ⅲ, it increases the opening force and stiffness-leakage ratio. This work can provide theory and data to help with the subsequent optimization design of gas face seals for aero-engine.
- 2 November 2023
- Published by ASME International in Journal of Tribology
- Vol. 146 (2) , 1-43
Evolution and Action Mechanism of Relative Negative Pressure Zone in Spiral Groove Gas Face Seal for Aero-Engine
As an advanced sealing technology, the application of gas face seal in aero-engine is few; if possible, lower specific fuel consumption, higher thrust-weight ratio, and effective secondary flow control at minimal cost would be brought. A relative negative pressure zone (RNPZ) was found in the spiral groove gas face seal, and the evolution and action mechanism of RNPZ was investigated in detail, which may promote the above application. Three film thicknesses of spiral groove gas face seals at different rotational speeds and inlet pressures were numerically compared to obtain the pressure field in the groove area and the formation of RNPZ. Then, the radial and circumferential velocities in the groove were calculated to quantify the impact of the obstruction effect, viscous pumping, and shear effect, which revealed the evolution mechanism of the RNPZ stage by stage. At last, the action mechanism of RNPZ was clarified through the hydrodynamic performance analysis. It is found that the pressure field evolution in the gas face seal is in stage Ⅲ under the high rotational speed and low inlet pressure conditions in an aero-engine. Under the same film thickness, RNPZ can suppress leakage to a certain extent in stage Ⅱ, while in stage Ⅲ, it increases the opening force and stiffness-leakage ratio. This work can provide theory and data to help with the subsequent optimization design of gas face seals for aero-engine.
- 19 July 2023
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (8) , 1-47
Effects of High Rotational Speed on Leakage and Windage Heating of Staggered Labyrinth Seals With Smooth and Honeycomb Lands
Being an important component of aero-engines, the labyrinth seal has always been the focus of research for leakage characteristics. Rotation is usually neglected or taken for minimal effect on seal leakage in previous studies. However, the effect of high rotational speed is inevitable to understand the leakage characteristics of labyrinth seal accurately. Meanwhile, due to high rotational speed, viscous heat is generated massively to result in the rapid temperature rise of leakage flow. Also, the influence of rotational speed on windage heating inside the seal clearance has not been indicated completely. Therefore, the leakage and windage heating of staggered labyrinth seals with smooth and honeycomb lands were experimentally and numerically studied. The large-scale and multifunctional sealing test rig were employed to carry out the experiments with rotational speed 12,000 rpm and pressure ratio range 1.1–2.2. The simulation data obtained by three-dimensional computational fluid dynamics methodology show great agreement with experimental results. Notably, the leakage coefficient is not monotonically decreasing with increased rotational speed, but exists a maximum peak at RPM = 8000. The variation of axial kinetic energy in seal clearance entrances provides a clear explanation of the phenomenon. Rotational speed plays an important role in windage heating, and honeycomb cell size is of secondary importance. Based on simulation data, the calculating formula of windage heating is fitted and shows great performance. This study can provide theory and data support for the follow-up structural optimum design of the labyrinth seal.
- 19 July 2023
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (8) , 1-47
Effects of High Rotational Speed on Leakage and Windage Heating of Staggered Labyrinth Seals With Smooth and Honeycomb Lands
Being an important component of aero-engines, the labyrinth seal has always been the focus of research for leakage characteristics. Rotation is usually neglected or taken for minimal effect on seal leakage in previous studies. However, the effect of high rotational speed is inevitable to understand the leakage characteristics of labyrinth seal accurately. Meanwhile, due to high rotational speed, viscous heat is generated massively to result in the rapid temperature rise of leakage flow. Also, the influence of rotational speed on windage heating inside the seal clearance has not been indicated completely. Therefore, the leakage and windage heating of staggered labyrinth seals with smooth and honeycomb lands were experimentally and numerically studied. The large-scale and multifunctional sealing test rig were employed to carry out the experiments with rotational speed 12,000 rpm and pressure ratio range 1.1–2.2. The simulation data obtained by three-dimensional computational fluid dynamics methodology show great agreement with experimental results. Notably, the leakage coefficient is not monotonically decreasing with increased rotational speed, but exists a maximum peak at RPM = 8000. The variation of axial kinetic energy in seal clearance entrances provides a clear explanation of the phenomenon. Rotational speed plays an important role in windage heating, and honeycomb cell size is of secondary importance. Based on simulation data, the calculating formula of windage heating is fitted and shows great performance. This study can provide theory and data support for the follow-up structural optimum design of the labyrinth seal.