Bertrand Jodoin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bertrand Jodoin has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
A. Tieu
VLN Advanced Technologies Inc. 2 , Ottawa, Ontario K1J 6X7, Canada
1 shared publication- Aleksandra Nastic
University of Ottawa
1 shared publication Antoine Corbeil
Brayton Energy Canada, 710 rue Vernon, Unité #7, Gatineau, Québec J9J 3K5, Canada
1 shared publicationAosong Li
1 shared publicationAslan Farjam
University of Ottawa, 161 Louis Pasteur Av., Ottawa, Ontario K1N 6N5, Canada
1 shared publicationJ. Son
University of Ottawa and National Research Council Canada, Ottawa, ON, Canada
1 shared publication
Latest Publications
- Open Access
Role of tamping effect in wear behavior of Cu-TiC composite coatings deposited by cold spray
- Open Access
- 8 November 2024
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 129 (1331) , 63-83
Isolating influences of varying pitch from the effects of non-zero compound angles on effusion cooling
Effusion cooling is the state-of-the-art cooling technology for gas turbine hot-gas path components. Typically, effusion cooling holes across the entire combustor liner are aligned with the combustor axis, rendering a nominal zero compound angle between highly directional miniature effusion cooling jets and the main flow direction. The pitch of effusion cooling holes is optimised accordingly. However, the swirling main flow results in a non-zero compound angle and an effectively different pitch from the design. The directional effect of effusion cooling as a result of swirling main flow on the adiabatic film cooling effectiveness (AFE) is a combined effect of a non-zero compound angle and a varied pitch. The current experimental study aims to investigate the isolated effects of compound angle on AFE by excluding the influences of varying pitch. With an improved understanding of the sole effects of non-zero compound angles on AFE, the roles that a varied pitch plays in modifying AFE are further discussed to guide future effusion cooling designs under swirling main flow conditions. Binary pressure sensitive paint (PSP) was used to determine AFE experimentally.
- 8 November 2024
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 129 (1331) , 63-83
Open AccessIsolating influences of varying pitch from the effects of non-zero compound angles on effusion cooling
Effusion cooling is the state-of-the-art cooling technology for gas turbine hot-gas path components. Typically, effusion cooling holes across the entire combustor liner are aligned with the combustor axis, rendering a nominal zero compound angle between highly directional miniature effusion cooling jets and the main flow direction. The pitch of effusion cooling holes is optimised accordingly. However, the swirling main flow results in a non-zero compound angle and an effectively different pitch from the design. The directional effect of effusion cooling as a result of swirling main flow on the adiabatic film cooling effectiveness (AFE) is a combined effect of a non-zero compound angle and a varied pitch. The current experimental study aims to investigate the isolated effects of compound angle on AFE by excluding the influences of varying pitch. With an improved understanding of the sole effects of non-zero compound angles on AFE, the roles that a varied pitch plays in modifying AFE are further discussed to guide future effusion cooling designs under swirling main flow conditions. Binary pressure sensitive paint (PSP) was used to determine AFE experimentally.
- Open Access
- 1 May 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (5)
High speed water droplet impact erosive behavior on dry and wet pulsed waterjet treated surfaces
During water droplet impact onto a dry or wet rough solid surface, several phenomena affect the surface erosion process, such as splashing, crown formation, and small droplet emission to name a few. These phenomena have been extensively studied for various simple target surface geometries. However, droplet impact studies on complex irregular and asymmetric target surface topographies resulting from a waterjet treatment have never been conducted. Furthermore, very limited reports are found on the role of target surface topography and water droplet deformation development on the resulting target stress state. In the present study, high speed droplet impingements on surfaces exhibiting coarse topographical features associated with ultrasonic pulsed waterjet treatment are modeled to understand the underlying mechanisms causing erosion. Impacts on surfaces with various roughness values and water film thicknesses are modeled using a three-dimensional coupled Eulerian–Lagrangian approach. A detailed comparative analysis of the model with experimental ultrasonic pulsed waterjet erosion features and material loss is provided. It was found that the synclastic curvature of the modeled coarse surface features increases the shock wave's strength as many compression wavelets are simultaneously emitted at each water droplet contact location with the surface, resulting in concentrated high-pressure zones. The ultrasonic pulsed waterjet treated surface features and water film thickness also greatly influence the onset of water droplet splashing, subsequent finger, secondary droplet characteristics, and crown stability. According to the numerical results, strong splashing patterns and droplet breakup are generated and create high stress zones capable of accelerating surface erosion, explaining the enhanced performance of ultrasonic pulsed waterjet process.
- 1 May 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (5)
Open AccessHigh speed water droplet impact erosive behavior on dry and wet pulsed waterjet treated surfaces
During water droplet impact onto a dry or wet rough solid surface, several phenomena affect the surface erosion process, such as splashing, crown formation, and small droplet emission to name a few. These phenomena have been extensively studied for various simple target surface geometries. However, droplet impact studies on complex irregular and asymmetric target surface topographies resulting from a waterjet treatment have never been conducted. Furthermore, very limited reports are found on the role of target surface topography and water droplet deformation development on the resulting target stress state. In the present study, high speed droplet impingements on surfaces exhibiting coarse topographical features associated with ultrasonic pulsed waterjet treatment are modeled to understand the underlying mechanisms causing erosion. Impacts on surfaces with various roughness values and water film thicknesses are modeled using a three-dimensional coupled Eulerian–Lagrangian approach. A detailed comparative analysis of the model with experimental ultrasonic pulsed waterjet erosion features and material loss is provided. It was found that the synclastic curvature of the modeled coarse surface features increases the shock wave's strength as many compression wavelets are simultaneously emitted at each water droplet contact location with the surface, resulting in concentrated high-pressure zones. The ultrasonic pulsed waterjet treated surface features and water film thickness also greatly influence the onset of water droplet splashing, subsequent finger, secondary droplet characteristics, and crown stability. According to the numerical results, strong splashing patterns and droplet breakup are generated and create high stress zones capable of accelerating surface erosion, explaining the enhanced performance of ultrasonic pulsed waterjet process.
- 1 August 2014
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 75, 235-244
Additive manufacturing of pyramidal pin fins: Height and fin density effects under forced convection
- 1 August 2014
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 75, 235-244
Additive manufacturing of pyramidal pin fins: Height and fin density effects under forced convection