Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kostyantyn Holenko has a total of 49 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Comparative Structural Response of Conventional and Hybrid Seat–Handrail Systems in a Low-Floor Urban Bus

    by Kostiantyn Holenko, Oleksandr Dykha, Anna PięTocha, Ivan Kernytskyy, Orest Horbay, Yuriy Royko, Taras Postranskyy, Andrii Sharybura, Ruslan Humeniuk, Vasyl Rys, et al.

    Integrating passenger seats with the load-bearing framework of low-floor urban buses changes seat-support connectivity and motivates comparison of alternative structural layouts. This study compares conventional floor-mounted seats with a hybrid seat–handrail system connected to both the floor and roof. Finite element analyses were performed using Ansys Explicit Dynamics for a simplified frontal impact at 30 km/h and Ansys Transient Structural for separate seat-back loading based on force prescriptions from UN Regulation No. 80 (R80). Tubular members were represented by beam elements, with common prescribed loading and boundary conditions used for each configuration pair. In the baseline force-based impact simulations, the hybrid configuration reduced peak seat-back displacements by 11.44% for the 1st seat and 1.90% for the 4th seat. The simulated peak structural backrest acceleration decreased from 10.2 g to 8.6 g. Under prescribed seat-back loading, peak Y-axis displacements of the upper backrest crossbars decreased from 518.71–518.72 mm to 51.12–55.99 mm, representing reductions of approximately 90% across the four seats. The comparison demonstrates that the structural influence of seat–handrail integration is strongly dependent on the loading scenario and seat location. These findings support further development of integrated seat-support layouts and investigation of attachment stiffness and load transfer.

  • Open Access

    Prestressed Cable-Spring Joints as a Lightweight Reinforcement Strategy for Tubular Body Structures in Conventional and Autonomous Buses

    by Kostiantyn Holenko, Oleksandr Dykha, Marco Guerrieri, Larysa Neduzha

    Bus body structures are commonly reinforced by increasing the dimensions or number of steel members, resulting in higher vehicle mass and material consumption. This study proposes a lightweight reinforcement concept based on prestressed Cable Spring (CS) joints for tubular bus body structures. An analytical model describing the stiffness contribution of tension-only prestressed cables was developed and implemented in Ansys Mechanical. The concept was evaluated using finite-element models of the low-entry city bus body “4289” under two representative loading conditions: diagonal racking and inertial loading prescribed by UNECE Regulation No. 100 (R100). Under diagonal racking, the proposed CS system reduced the maximum von Mises stress by 2.7%, the average stress by 16.2%, and the maximum total deformation by 28.4%. Under the R100 transverse 5 g loading condition, the combined catenary-curved and CS configuration decreased the maximum equivalent stress, average stress, and maximum deformation by 41.2%, 24.7%, and 75.1%, respectively, relative to the conventional rectangular body frame. The results demonstrate that prestressed CS joints constitute an effective lightweight reinforcement strategy for improving the structural efficiency of tubular body structures of conventional and autonomous buses, with these benefits being primarily associated with reduced structural material use.

  • Analytical and Numerical Evaluation of Multifunctional Spatial Trusses on Certified Truck Frames

    by Kostyantyn Holenko, Oleksandr Dykha, Maksym Dykha, Volodymyr Dytyniuk, Mykhailo Burian

  • Open Access

    Side-Impact Crashworthiness of Low-Emission Electric Bus with Battery-Integrated Inter-Window Pillars Under UNECE R95 Conditions

    by Kostiantyn Holenko, Oleksandr Dykha, Anna PięTocha, Ivan Kernytskyy, Orest Horbay, Wojciech Górski, Eugeniusz Koda

    This study investigates the side-impact crashworthiness of a low-floor electric bus with traction batteries integrated into the inter-window pillars of the body structure. A finite-element model of the bus body was developed in Ansys and used to evaluate six impact scenarios involving conventional diesel and battery-integrated configurations. The analysis included evaluation of von Mises stresses, structural safety margins, deformation fields, strain energy, and transient nodal velocity response. The battery-integrated configuration demonstrated improvements in key crashworthiness indicators across the investigated impact scenarios, with both the average maximum deformation and the averaged equivalent stress reduced by approximately one quarter compared with the conventional configuration. The stress state of the inter-window pillars remained below the local structural failure levels observed in the conventional configuration, with the maximum pillar stress criterion reduced by more than half. Simultaneously, lower transient nodal velocities indicated reduced transmission of impact momentum toward the occupant compartment and more efficient redistribution of impact energy through the body structure. The results demonstrate the feasibility of using battery-integrated inter-window pillars as multifunctional structural members that simultaneously serve as energy storage and enhance the side-impact crashworthiness of low-floor electric buses.


  • Open Access

    Conceptual Electric Bus Body Structure with Battery-Integrated Pillars: Beam-Based Finite Element Modelling and UNECE R66 Rollover Assessment

    by Kostiantyn Holenko, Oleksandr Dykha, Anna Markiewicz, Anna PięTocha, Ivan Kernytskyy, Orest Horbay, Eugeniusz Koda

    The electrification of urban buses under forthcoming Euro 7 regulations requires new structural solutions ensuring both safety and efficient mass distribution. This study proposes a novel conceptual electric bus body structure with battery-integrated inter-window pillars, in which energy storage systems are embedded. The concept was evaluated using finite element analysis in ANSYS under UNECE R66 rollover conditions by comparing an original diesel configuration (O-model) with a battery-integrated electric (B-model) one. Despite a substantial increase in body mass (from 1947 to 5464 kg), the B-model demonstrated improved structural performance. The maximum deformation decreased from 1489.5 to 1319.7 mm, while the difference between the control point displacements decreased from 32.21 to 12.68 mm. The average relative deformation of pillars decreased from 8.48% to 3.59%, and the intrusion amplitude was reduced from approximately 566 to 167 mm. Analysis showed comparable peak von Mises stresses (414.62 MPa vs. 439.19 MPa), but the B-model exhibited a 6.7% reduction in critical regions and a 16.9% decrease in average stress levels. The B-model remained within the elastic regime at the end of the simulation, whereas the O-model showed residual plastic deformation. The results indicate that integrating battery systems into load-bearing pillars leads to improved structural stiffness and deformation behaviour under rollover conditions, while full certification-level verification of UNECE R66 compliance is beyond the scope of the present study.


  • Open Access

    Wear prediction and material selection of contact inserts for electric transport based on energy model using the finite element method

    by Kostiantyn Holenko, Oleksandr Dykha, Orest Horbay, Oleksii Kovtun, Volodymyr Dytyniuk

    This study explores the contact pair «trolleybus contact insert «TCI-power wire». The task addressed relates to the lack of consideration of thermal effects, phase changes, and thermal softening of the material in the classical Archard and Karman models, which complicates wear prediction. To solve this problem, an energy-temperature wear model (ETW) has been constructed, which integrates mechanical, thermal, and energy processes in the contact zone. Unlike existing approaches, the model considers the temperature-dependent hardness H(T) and local fields of contact pressure and frictional stresses, determined by the finite element method (FEM) in the Ansys environment. The research features involve a hybrid approach to wear prediction – the integration of mathematical modeling and FEM simulation. The results include von Mises stresses σmax = 16.24 MPa (amorphous carbon), 18.99 MPa (electrographite – EG), and 30.53 MPa (copper-graphite composite Cu-40%C(f) 0.90 – CU). Under sliding conditions of Stotal = 0.2 m at contact pressure p = 0.5 MPa, the wear depth for EG is 1.99·10⁻5 mm, which is extrapolated to 47.8 mm at 450 km and exceeds the permissible 10 mm, while for CU the wear decreases to 2.2 mm. The wear reduction is associated with the greater hardness of CU (120–135 HV) and a uniform distribution of contact stresses, which confirms the ETW effectiveness. Practical significance of the results is the possibility of a reasonable choice of TCI materials, in particular copper-fullerene composites (Cu-0.5% FS), to increase wear resistance and stability of current collection with priority insert wear over the contact wire. The scope of practical implementation of the results includes the design of materials for current collection systems of electric transport

  • Open Access

    Evaluation of Influence of the Integrated Welded Handrail System in the Bus Body Frame on Strength and Passive Safety

    by Kostyantyn Holenko, Eugeniusz Koda, Oleksandr Dykha, Ivan Kernytskyy, Orest Horbay, Marek Chalecki, Yuriy Royko, Ruslan Humeniuk, Andrii Sharybura, Yaroslav Sholudko, et al.

    Achieving the EU 2030 target of a 30% CO2 reduction requires transitioning intercity buses to CNG- or fuel-cell-driven vehicles, and urban buses to electric vehicles. The increasing mass of roof-mounted energy systems, such as battery packs, creates additional loads on the body frame. This study investigates the integration of a welded handrail system into the bus body frame as an additional load-bearing element. A combined approach based on dynamic modeling and finite element analysis was applied to evaluate the structural body response under the UNECE R100 and R110 regulations. The results demonstrate that the structural concept significantly improves the stress–strain state of the body frame. Maximum roof displacements under 5g loading decreased by 34% for the gas-powered model and by 50% for the electric model, enhancing passive safety by reducing window-rack intrusion. Maximum stress decreased by 20%, shifting the stress state below the ultimate strength of S235 steel and preventing rupture. Uniform strength under vertical loading increased significantly (by 58%) due to a more favorable stress distribution within the structure. Overall, the results indicate that integrating a welded handrail truss into the bus body frame can effectively improve structural stiffness and redistribute loads within the frame.


  • Improving Heating of a Bus Interior Using a Combined Heating System

    by Yurii Voichyshyn, Vitaliy Popovych, Orest Horbay, Kostyantyn Holenko, Aleksandr Dykha


  • Open Access

    Analysis of frictional stresses and wear in the contact pair of a vehicle current collector

    by O.S. Kovtun, K.E. Holenko, A.L. Ganzyuk, M.O. Dykha, V.O. Dytyniuk

    The article presents the results of numerical modeling of the operation of the trolleybus current collector pair "contact insert - wire" using the Ansys software environment. The distribution of frictional stresses (Frictional Stress) and contact pressures for two types of insert materials is analyzed: electrographite (Electrographite, parallel to plane) and copper-graphite composite Cu–40%C(f) 0.90 laminate. It was established that the real area of the contact spot is smaller than the entire surface of the gutter, which significantly affects the calculated values of the average frictional stresses and, accordingly, the wear forecast. For the electrographite insert, the average value of Frictional Stress was 0.439 MPa, for the copper-graphite insert – 0.599 MPa. The calculations showed that at a mileage of 450 km, the wear of the electrographite insert exceeds the permissible value, while for the copper-graphite one it is 2.1564 mm and is within the normal range. However, due to the higher hardness of the copper-graphite material compared to the copper wire, the wire itself can become the main element of wear, which is undesirable. It was concluded that the optimal option may be to use a material with intermediate hardness, which will provide a balance between the wear resistance of the insert and the preservation of the contact wire resource.

  • Open Access

    Peculiarities of Assessing Body Strength When Converting a Bus from Diesel to Electric Traction Following the UNECE R100 Regulation

    by Kostyantyn Holenko, Oleksandr Dykha, Eugeniusz Koda, Ivan Kernytskyy, Orest Horbay, Yuriy Royko, Ruslan Humeniuk, Yaroslav Sholudko, Vasyl Rys, Serhii Berezovetskyi, et al.

    The problem of the conversion of diesel buses to electric ones in connection with the inevitable introduction of the EURO 7 emission standards entails an automatic requirement to follow several additional United Nations Economic Commission for Europe rules, like R100 regulations. They regulate the preservation of battery units at longitudinal 12 g and transverse 10 g accelerations without penetrating into the elements of the bus body. Three models (12 modes in total) of battery units with frames made of S235 steel were analysed. The maximum stress value varies between 364.89 MPa and 439.08 MPa in 10 g and 12 g modes, respectively, which is beyond the tensile strength (360 MPa) and provokes plastic deformations. The max deformations were recorded in the models with the highest average stress: 63.04 mm in the 12 g mode with an average stress of 83.18 MPa. The minimum deformations of 6.95 and 7.95 mm were found in the 10 g modes (left and right acceleration direction, respectively), which meet the manufacturer’s requirements (45–50 mm maximum). The study’s primary contribution lies in developing a practical method for assessing battery unit integrity and structural behaviour during the conversion of diesel buses to electric propulsion, fully compliant with R100 regulations. By combining transient structural simulation, mathematical centre modelling of acceleration propagation, and centre of gravity prediction, the proposed approach enables engineers to evaluate electric conversions’ safety and certification feasibility without modifying the existing bus body.