Dinislam I. Sadykov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Dinislam I. Sadykov has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Tatiana S. Orlova
Физико-технический институт им. А.Ф. Иоффе РАН, Санкт-Петербург, Россия
5 shared publications - Aydar M. Mavlyutov
Mathematics and Mechanics Faculty, Saint Petersburg State University, 199034 Saint Petersburg, Russia
4 shared publications - Demid Aleksandrovich Kirilenko
St. Petersburg State University, St Petersburg, 199034, Russia
4 shared publications - Maxim Yurievich Murashkin
Ufa University of Science and Technology, Ufa, Russia
3 shared publications - Nariman A. Enikeev
Laboratory of Metals and Alloys under Extreme Impacts, Ufa University of Science and Technology, 450076 Ufa, Russia
3 shared publications A.I. Lihachev
2 shared publications
Latest Publications
- Open Access
- 28 August 2026
- Published by Elsevier in SSRN Electronic Journal
Bright Light Emission Under Low-Voltage Breakdown of (100) β-Ga2O3 Single-Crystal Plates
Crystal plates cleaved from β-Ga2O3 boules grown from the melt are the most prospective for gallium-oxide-based semiconductor devices. In this study, we report low-voltage electrical breakdown, 80–100 V DC, in centimeter-scale (100) β-Ga2O3 single-crystal plates. This breakdown consists of reversible and catastrophic stages and is accompanied by intense light emission in a wide IR-UV range with a peak value at 1.39 eV and a spectral dip at 1.59 eV. We attribute this phenomenon to the formation of filamentary conducting paths in the central part of the plates. These paths emerge due to intense Joule heating localized by the low thermal conductivity inherent to β-Ga2O3.
- 28 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessBright Light Emission Under Low-Voltage Breakdown of (100) β-Ga2O3 Single-Crystal Plates
Crystal plates cleaved from β-Ga2O3 boules grown from the melt are the most prospective for gallium-oxide-based semiconductor devices. In this study, we report low-voltage electrical breakdown, 80–100 V DC, in centimeter-scale (100) β-Ga2O3 single-crystal plates. This breakdown consists of reversible and catastrophic stages and is accompanied by intense light emission in a wide IR-UV range with a peak value at 1.39 eV and a spectral dip at 1.59 eV. We attribute this phenomenon to the formation of filamentary conducting paths in the central part of the plates. These paths emerge due to intense Joule heating localized by the low thermal conductivity inherent to β-Ga2O3.
- 28 August 2025
- Published by Elsevier in Materials Letters
- Vol. 403
Influence of low temperatures on outstanding mechanical properties of ultrafine-grained Al-5Mg alloy
- 28 August 2025
- Published by Elsevier in Materials Letters
- Vol. 403
Influence of low temperatures on outstanding mechanical properties of ultrafine-grained Al-5Mg alloy
- Open Access
- 28 December 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 34, 2329-2343
Superior strength-ductility synergy in ultrafine-grained Al–5Mg alloy
- 28 December 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 34, 2329-2343
Open AccessSuperior strength-ductility synergy in ultrafine-grained Al–5Mg alloy
- 2 December 2024
- Published by Elsevier in Materials Letters
- Vol. 382
Achieving synergy of high strength and ductility in ultrafine-grained aluminium through annealing and cryorolling
- 2 December 2024
- Published by Elsevier in Materials Letters
- Vol. 382
Achieving synergy of high strength and ductility in ultrafine-grained aluminium through annealing and cryorolling
- Open Access
- 1 March 2024
- Published by KEAI Publishing in International Journal of Lightweight Materials and Manufacture
- Vol. 7 (2) , 221-232
Influence of ultrafine-grained structure parameters on the annealing-induced hardening and deformation-induced softening effects in pure Al
- 1 March 2024
- Published by KEAI Publishing in International Journal of Lightweight Materials and Manufacture
- Vol. 7 (2) , 221-232
Open AccessInfluence of ultrafine-grained structure parameters on the annealing-induced hardening and deformation-induced softening effects in pure Al
- Open Access
Effect of Deformation-Induced Plasticity in Low-Alloyed Al-Mg-Zr Alloy Processed by High-Pressure Torsion
The influence of additional deformation heat treatments (DHTs), implemented by two regimes: (1) annealing and small additional deformation by high-pressure torsion (HPT) at room temperature (RT) and (2) HPT at elevated temperature to 10 turns and small additional HPT at RT, has been studied on the microstructure, mechanical properties and electrical conductivity of ultrafine-grained (UFG) Al-0.53Mg-0.27Zr (wt.%) alloy structured by HPT to 10 turns at RT. As is shown, both types of additional DHT lead to a substantial increase in plasticity (2–5 times) while maintaining high electrical conductivity (~53% IACS) and strength comprising 75–85% of the value in the pre-DHT state of the UFG alloy. The possible physical reasons for the revealed changes in the physical and mechanical properties are analyzed. Comparison of the strength and plasticity changes with the microstructure evolution after DHT of both types indicates that the increase in the density of introduced grain boundary dislocations is the most probable factor providing a tremendous increase in plasticity while maintaining a high level of strength in the UFG alloy under study. An outstanding combination of high strength (370 MPa), high elongation to failure (~15%) and significant electrical conductivity (~53% IACS) was achieved for the Al-Mg-Zr alloy. This combination of properties exceeds those obtained to date for this system, as well as for a number of other commercial conductor alloys based on the Al-Zr system.
Open AccessEffect of Deformation-Induced Plasticity in Low-Alloyed Al-Mg-Zr Alloy Processed by High-Pressure Torsion
The influence of additional deformation heat treatments (DHTs), implemented by two regimes: (1) annealing and small additional deformation by high-pressure torsion (HPT) at room temperature (RT) and (2) HPT at elevated temperature to 10 turns and small additional HPT at RT, has been studied on the microstructure, mechanical properties and electrical conductivity of ultrafine-grained (UFG) Al-0.53Mg-0.27Zr (wt.%) alloy structured by HPT to 10 turns at RT. As is shown, both types of additional DHT lead to a substantial increase in plasticity (2–5 times) while maintaining high electrical conductivity (~53% IACS) and strength comprising 75–85% of the value in the pre-DHT state of the UFG alloy. The possible physical reasons for the revealed changes in the physical and mechanical properties are analyzed. Comparison of the strength and plasticity changes with the microstructure evolution after DHT of both types indicates that the increase in the density of introduced grain boundary dislocations is the most probable factor providing a tremendous increase in plasticity while maintaining a high level of strength in the UFG alloy under study. An outstanding combination of high strength (370 MPa), high elongation to failure (~15%) and significant electrical conductivity (~53% IACS) was achieved for the Al-Mg-Zr alloy. This combination of properties exceeds those obtained to date for this system, as well as for a number of other commercial conductor alloys based on the Al-Zr system.
- Open Access
Influence of Decreased Temperature of Tensile Testing on the Annealing-Induced Hardening and Deformation-Induced Softening Effects in Ultrafine-Grained Al–0.4Zr Alloy
The influence of decreased temperature of tensile testing on annealing-induced hardening (AIH) and deformation-induced softening (DIS) effects has been studied in an ultrafine-grained (UFG) Al–Zr alloy produced by high-pressure torsion. We show that the UFG Al–Zr alloy demonstrates a DIS effect accompanied by a substantial increase in the elongation to failure δ (up to δ ≈ 30%) depending on the value of additional straining. Both the AIH and DIS effects weaken with a decrease in the tensile test temperature. The critical deformation temperatures were revealed at which the AIH and DIS effects are suppressed. The activation energy Q of plastic flow has been estimated for the UFG Al–Zr alloy in the as-processed, subsequently annealed and additionally strained states. It was shown that the annealing decreases the Q-value from ~80 kJ/mol to 23–28 kJ/mol, while the subsequent additional straining restores the initial Q-value. Alloying with Zr results in the expansion of the temperature range of the AIH effect manifestation to lower temperatures and results in the change in the Q-value in all of the studied states compared to the HPT-processed Al. The obtained Q-values and underlying flow mechanisms are discussed in correlation with specific microstructural features and in comparison to the UFG Al.
Open AccessInfluence of Decreased Temperature of Tensile Testing on the Annealing-Induced Hardening and Deformation-Induced Softening Effects in Ultrafine-Grained Al–0.4Zr Alloy
The influence of decreased temperature of tensile testing on annealing-induced hardening (AIH) and deformation-induced softening (DIS) effects has been studied in an ultrafine-grained (UFG) Al–Zr alloy produced by high-pressure torsion. We show that the UFG Al–Zr alloy demonstrates a DIS effect accompanied by a substantial increase in the elongation to failure δ (up to δ ≈ 30%) depending on the value of additional straining. Both the AIH and DIS effects weaken with a decrease in the tensile test temperature. The critical deformation temperatures were revealed at which the AIH and DIS effects are suppressed. The activation energy Q of plastic flow has been estimated for the UFG Al–Zr alloy in the as-processed, subsequently annealed and additionally strained states. It was shown that the annealing decreases the Q-value from ~80 kJ/mol to 23–28 kJ/mol, while the subsequent additional straining restores the initial Q-value. Alloying with Zr results in the expansion of the temperature range of the AIH effect manifestation to lower temperatures and results in the change in the Q-value in all of the studied states compared to the HPT-processed Al. The obtained Q-values and underlying flow mechanisms are discussed in correlation with specific microstructural features and in comparison to the UFG Al.
- Open Access
- 1 April 2022
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2231 (1) , 012005
Strength, thermal resistance and electrical conductivity of aluminum-based composite wire
In this work, we demonstrate the possibility of producing a composite high strength and thermal resistant Al-based wire with ultrafine-grained (UFG) structure. Such composite wire consists of two aluminum alloys. Its clad is made of Al-1.17Mg-0.35Zr (wt.%) alloy, and the core is of Al-0.4Zr (wt.%). The specimens of Al alloys separately and as parts of a composite wire were subjected to thermomechanical treatment (TMT) that included annealing at 400°C, equal-channel angular pressing via “Conform” scheme (ECAP-C) and cold drawing (CD). The ratio between the core and clad materials in the composite wire was determined experimentally as well as calculated from the rule of mixtures (additivity). It has been shown that, an ultimate tensile strength over 360 MPa and a long-term operation temperature of 150°C can be achieved in a composite wire at a rational ratio between the chosen aluminum alloys with the UFG structures. Such combination of strength and thermal resistance is accompanied with an electrical conductivity of no less than 50% IACS in a composite wire.
- 1 April 2022
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2231 (1) , 012005
Open AccessStrength, thermal resistance and electrical conductivity of aluminum-based composite wire
In this work, we demonstrate the possibility of producing a composite high strength and thermal resistant Al-based wire with ultrafine-grained (UFG) structure. Such composite wire consists of two aluminum alloys. Its clad is made of Al-1.17Mg-0.35Zr (wt.%) alloy, and the core is of Al-0.4Zr (wt.%). The specimens of Al alloys separately and as parts of a composite wire were subjected to thermomechanical treatment (TMT) that included annealing at 400°C, equal-channel angular pressing via “Conform” scheme (ECAP-C) and cold drawing (CD). The ratio between the core and clad materials in the composite wire was determined experimentally as well as calculated from the rule of mixtures (additivity). It has been shown that, an ultimate tensile strength over 360 MPa and a long-term operation temperature of 150°C can be achieved in a composite wire at a rational ratio between the chosen aluminum alloys with the UFG structures. Such combination of strength and thermal resistance is accompanied with an electrical conductivity of no less than 50% IACS in a composite wire.