Junyu Fu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Junyu Fu has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Bin Zhao
College of Mechanical and Vehicle Engineering, Taiyuan University of Technology, Taiyuan 030024, China
1 shared publication - Feng Li
College of Mechanical and Vehicle Engineering, Taiyuan University of Technology, Taiyuan, China
1 shared publication - Guangjun Liu
College of Mechanical Engineering, Taiyuan University of Technology, Taiyuan, China
1 shared publication - Haojie Li
College of Mechanical Engineering, Taiyuan University of Technology, Taiyuan, China
1 shared publication - Honglei Zhen
College of Mechanical and Vehicle Engineering, Taiyuan University of Technology, Taiyuan 030024, China
1 shared publication - Long Quan
Taiyuan University of Technology
1 shared publication
Latest Publications
- 2 June 2023
- Published by Springer Nature in Macromolecular Research
- Vol. 31 (9) , 883-896
Investigating the miscibility of poly (butylene adipate-co-terephthalate)/poly (lactic acid) mixtures through multi-scale simulation and experiments
- 2 June 2023
- Published by Springer Nature in Macromolecular Research
- Vol. 31 (9) , 883-896
Investigating the miscibility of poly (butylene adipate-co-terephthalate)/poly (lactic acid) mixtures through multi-scale simulation and experiments
- Open Access
Effect of 3D Printing Process Parameters and Heat Treatment Conditions on the Mechanical Properties and Microstructure of PEEK Parts
Fused deposition modeling (FDM) processed Poly-ether-ether-ketone (PEEK) materials are widely used in aerospace, automobile, biomedical, and electronics industries and other industries due to their excellent mechanical properties, thermal properties, chemical resistance, wear resistance, and biocompatibility, etc. However, the manufacture of PEEK materials and parts utilizing the FDM process faces the challenge of fine-tuning a list of process parameters and heat treatment conditions to reach the best-suiting mechanical properties and microstructures. It is non-trivial to make the selection only according to theoretical analysis while counting on a vast number of experiments is the general situation. Therefore, in this paper, the extrusion rate, filling angle, and printing orientation are investigated to adjust the mechanical properties of 3D-printed PEEK parts; then, a variety of heat treatment conditions were applied to tune the crystallinity and strength. The results show that the best mechanical performance is achieved at 1.0 times the extrusion rate, varied angle cross-fillings with ±10° intervals, and vertical printing. Horizontal printing performs better with reduced warpage. Additionally, both crystallinity and mechanical properties are significantly improved after heat treatment, and the best state is achieved after holding at 300 °C for 2 h. The resulting tensile strength is close to 80% of the strength of injection-molded PEEK parts.
Open AccessEffect of 3D Printing Process Parameters and Heat Treatment Conditions on the Mechanical Properties and Microstructure of PEEK Parts
Fused deposition modeling (FDM) processed Poly-ether-ether-ketone (PEEK) materials are widely used in aerospace, automobile, biomedical, and electronics industries and other industries due to their excellent mechanical properties, thermal properties, chemical resistance, wear resistance, and biocompatibility, etc. However, the manufacture of PEEK materials and parts utilizing the FDM process faces the challenge of fine-tuning a list of process parameters and heat treatment conditions to reach the best-suiting mechanical properties and microstructures. It is non-trivial to make the selection only according to theoretical analysis while counting on a vast number of experiments is the general situation. Therefore, in this paper, the extrusion rate, filling angle, and printing orientation are investigated to adjust the mechanical properties of 3D-printed PEEK parts; then, a variety of heat treatment conditions were applied to tune the crystallinity and strength. The results show that the best mechanical performance is achieved at 1.0 times the extrusion rate, varied angle cross-fillings with ±10° intervals, and vertical printing. Horizontal printing performs better with reduced warpage. Additionally, both crystallinity and mechanical properties are significantly improved after heat treatment, and the best state is achieved after holding at 300 °C for 2 h. The resulting tensile strength is close to 80% of the strength of injection-molded PEEK parts.