ASAngan Sengupta

Angan Sengupta

*This is an algorithmically generated author record based on publicly available information.

Angan Sengupta has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Molecular Simulations Revealing Adsorbent Heterogeneity-Induced Changes in Adsorption and Nonideal Behavior of Captured CO2 from Industrial Flue Gases with Varying Moisture

    by Shefali Gupta, Angan Sengupta, Gopinath Halder

    Selective CO2 capture from dry blast furnace gas (BFG) and moisture-varying steam methane reforming (SMR) flue gases using six heterogeneous silica adsorbents of comparable porosity, viz., StH and EnH, is quantified via classical molecular simulations. In these adsorbents, CO2-philicity from pure and mixture feeds is enhanced (compared to the previously shown silica slit pores) due to the heterogeneity-induced higher surface oxygen-to-surface-modified groups (−OH or O–Na+) ratio at pore surfaces, thereby increasing adsorbent selectivity for CO2 by decreasing the CO2 thermodynamic equilibrium ratio. In addition to increased CO2-philicity of StH and EnH adsorbents, CO2 adsorption in EnH is governed by combined “gating” and “crowding” effects depending on adsorption T and P, feed gas compositions, Si content, and sodium concentration near pore surfaces. However, the presence of water in the SMR mixture leads to competitive adsorption in the pores of StH and EnH, in contrast to dry BFG flue gas adsorption, hence making surface–CO2 interactions more attractive in the case of BFG adsorption than SMR adsorption. A closer arrangement of adsorbed CO2 near the pore surfaces and cluster formations of adsorbed water molecules have been observed in all adsorbents. Non-monotonic adsorption depends on adsorbate–adsorbate–adsorbent, adsorbate–adsorbate, and adsorbent–adsorbate interactions for pure CO2, whereas the latter two interactions dominate in defining H2O adsorption behaviour in all adsorbents. Spreading pressures (Π) are shown to vary with T, P, molar adsorbed area (A′), and excluded molar area (b′), with A′-b′ predominantly controlling positive Π variations. The estimated activity coefficient indicates nonideal behaviour of selectively adsorbed CO2 from BFG and SMR mixtures, with the activity coefficient ratio being inversely proportional to selectivity.

  • Conducting Yarn-Based Smart Wearables

    by Anupam Kumari, Angan Sengupta, Ajay Agarwal

    With the evolution in textile technology, clothing is expected to be more than just a shield or cover for the body. Integrating conducting yarns into textiles enables garments to act as point-of-care wearables, human–machine interaction, and ambient computing. Even though numerous studies about metallic, polymeric, and hybrid yarns-based laboratory prototypes exist, the transition from proof-of-concept devices to laundry-ready consumer products remains a significant challenge. This chapter presents a translational approach for yarn-based smart wearables, focusing on the transition from a controlled laboratory environment to reliable and real-world textile technology. The chapter begins with an overview of practical design matrices for conducting yarn materials and process selection for real-world use. Certain trade-offs among conductivity, flexibility, washability, scalability, and sustainability are also discussed. The central part of the chapter focuses on the durability and reliability of yarn-based sensors and international testing standards to meet the requirements. Some common wear and tear failure mechanisms, such as delamination, oxidation, and fatigue in yarns, have also been addressed. Drift, hysteresis, and user-to-user variability, which is often seen in yarn-based sensors, have been reviewed in this chapter with machine learning-driven calibration frameworks. The perspective further focuses on approaches for sustainable conducting yarn-based wearables, discussing eco-friendly fibers as substrate, biodegradable encapsulation, and circular design principles. The translational applications in terms of durability, user comfort, and eco-sustainability are discussed for healthcare, sports, industrial safety, and interactive fashion. Finally, a future roadmap is proposed, highlighting self-powered yarn, digital twin modeling, and standardized open data protocols that can boost the commercialization of conducting yarn-based wearables.

  • Open Access

    A Molecular Simulation Study on Sodium-Montmorillonite Clay Soil Stabilization through Calcium-Based Stabilizers

    by Aparna Singh, Angan Sengupta, Debanjan Guha Roy

    The most prevalent clay mineral found in soil is montmorillonite. Montmorillonite-rich soils also known as expansive soils can pose hazards that bring geotechnical challenges because their swelling or shrinking behaviour arises due to the large water retention capacity of montmorillonite-rich soils. This soil swelling reduces the shear strength of soil and results in differential settlement of foundation, which compromises the structural integrity of the infrastructure. Montmorillonite is made up of multiple-layer structures, and these interlayers contain free cations that enable attachment of water molecules, which cause volumetric expansion of the soil. To prevent swelling, calcium-based stabilizers are often utilized for sodium-montmorillonite (Na-MMT) clay stabilization. These calcium-based stabilizers replace sodium ions with calcium ions with creating a diffuse layer around clay particles that affects the water adsorption capacity of Na-MMT. Therefore, to ensure structural safety and soil stability, it is essential to predict accurate soil properties, which depend on soil-water interactions; a pore-scale study of soil stabilization provides an enhanced understanding of soil-water interactions and water adsorption in the clay, which is responsible for swelling in Na-MMT. This study examines water adsorption and soil-water interactions inside montmorillonite clay pores using the Monte Carlo molecular simulations to quantify the systematic exchange of sodium with calcium cations and their influence on swelling behaviour in montmorillonite. The pore width (multiple of d-spacing) ranges from 10 to 20 Å, and varied pH environment via change in Ca²⁺ cation exchange compositions upto 100% have been simulated under in-situ conditions of temperature range of 288 to 308 K and at a pressure of 1 atm. The ClayFF forcefield was used to modelled Na-MMT clay pore, and the SPCE forcefield was used to modelled the water molecules. The simulated bulk densities of water were validated with literature data at the considered thermodynamic conditions. The Ca²⁺ exchange indicated an influence on the hydration behaviour of Na-MMT and altered the molecular ordering of water inside the pore. The adsorption of water shows dependency on interactions between water and the pore surface, as well as the available pore volume. Furthermore, these simulations analysed the percentage change in cation composition on the surface using local density distribution profiles and pore pressure across the height of the pore. This study aims to provide molecular insights into the performance of calcium-based stabilisers on expansive soils and clay-water interactions, which will help to predict pore pressure, swelling and softening and improved stability of expansive soils.

  • A Molecular Simulation Study for Understanding the Effects of Two Water Channel Morphologies in Nafion with Various Hydration Levels on Adsorption and Nonideal Behaviour of Methanol at Operating Conditions of Direct Methanol Fuel Cells

    by Sarangi Veliyil Santhamma, Sahana Hanumanthappa Kenchgundi, Angan Sengupta

    Fuel loss inside direct methanol fuel cells (DMFCs) having Nafion membranes with two distinct water channel morphologies (viz., lamellar water channel morphology (LWCM) and random water channel morphology (RWCM), both validated against the literature having comparable equivalent weights and membrane densities) has been quantified through a methanol adsorption (ρCH3OH) study using GCMC simulations. Subsequently, variations in nonideality of adsorbed methanol as a function of Nafion-water-methanol local mole fractions are estimated at DMFC operating conditions, which are governed by ρCH3OH inside different morphologies. For all temperatures with given hydration (λ), ρCH3OH values are significantly higher inside LWCM with a single ordered channel compared to RWCM with localized hydrophilic regions and inherent tortuosity. While ρCH3OH decreases with increasing λ inside LWCM, inside RWCM, ρCH3OH is constantly lower at λ = 3 and varies relatively for λ = 6 and 9, depending on the DMFC operating temperature. Pore volume and active site availability in hydrated Nafion result in a competitive arrangement of methanol with respect to the bound water and hydronium mixture, only at the LWCM centre and at localized hydrophilic sites of RWCM. These observations have been justified further by estimating the preferential solvation parameters. Interestingly, the molecular ordering of bound water inside all Nafion remained invariant upon methanol adsorption. However, enhanced molecular ordering of adsorbed methanol in comparison to its pure bulk phase also indicates the possibility of activity coefficients (γCH3OH) < 1 inside hydrated Nafion. Calculations of excess entropy substantiate ρCH3OH,LWCM > ρCH3OH,RWCM, at constant water compositions.


  • Open Access

    Adsorption Isotherms Analysis of Liquid Nitrogen inside Montmorillonite and Kaolinite Rock Pores using Molecular Simulations

    by Aparna Singh, Angan Sengupta, Debanjan Guha Roy

    Hydraulic fracturing or fracking for shale gas and oil production is a water intensive and environmentally damaging process. It is often blamed for groundwater contamination and artificial earthquakes. Therefore, cryogenic fracking using liquid nitrogen (LN2) has recently emerged as much safer and greener alternative. This novel process enhances rock permeability by creating thermal fractures by subjecting hydrocarbon-bearing rocks to repeated freeze-thaw cycles. However, the extent and efficiency of this process depends on the constituent minerals of the rock. Clay minerals such as montmorillonite and kaolinite constitute on average approximately 30 to 35 % of shale. These phyllosilicate group of minerals, despite their common layered structures, vary in composition and arrangement, resulting in distinct properties. Therefore, total adsorption of LN2 in the clay minerals of shale must combine insights on their individual adsorption responses. It is essential to estimate the total and residual LN2 volumes trapped in pores that will impact the mobility of hydrocarbons. In this work, we studied adsorption behaviour of nitrogen inside the montmorillonite and kaolinite nanopores using Grand Canonical Monte Carlo (GCMC) simulations. The slit pores, with 5 nm, 8 nm, and 12 nm opening were simulated for reservoir pressures ranging from 50 to 95 MPa and temperatures from 300 to 355 K. The influence of pore size, composition, pressure, temperature, and fluid type were studied to understand the relationship between adsorption isotherms and excess properties. The Canonical Ensemble simulations were performed in conjunction with Widom’s insertion technique performed to estimate the average chemical potential and interaction among the N2 molecules calculated via pair distribution function. The N2 was precisely represented by TraPPE force field model. The simulated bulk phase densities of N2 were observed to be in good agreement with literature values. As shown by the pair correlation function obtained from the Canonical Ensemble simulations, the bulk phase N2 was in a supercritical thermodynamic state at rock-fluid equilibrium temperature and pressure. The results indicated that the pore volume on both surfaces played a crucial role in the behaviour of N2 adsorption. It was observed that the adsorption capacity of N2 was affected by the amount of available pore space, revealing insights into interactions between pore surface and adsorbed N2. Additionally, the study also confirmed that the extent of adsorption was dependent on surface area and morphology of the material. The adsorption isotherms exhibited a well-defined relationship with excess properties of adsorbed N2. Further, these simulations analysed the thermodynamic nature of adsorbed fluid within the pores using the molecular density distribution profiles across the height of the pore.