Aleksey B. Arbuzov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Aleksey B. Arbuzov has a total of 73 co-authors. Here are the top co-authors by number of shared publications:
- Vladimir A. Drozdov
Siberian Branch, Russian Academy of Sciences
7 shared publications - Dmitriy A. Shlyapin
Boreskov Institute of Catalysis
4 shared publications - Aleksandr V. Lavrenov
Center of New Chemical Technologies, Boreskov Institute of Catalysis, Siberian Branch, Russian Academy of Sciences, 644040, Omsk, Russia
3 shared publications - Evgeniy A. Buluchevskiy
Russian Academy of Sciences
3 shared publications - Mikhail V. Trenikhin
Center of New Chemical Technologies BIC, Boreskov Institute of Catalysis, Omsk, Russia
3 shared publications - T. I. Gulyaeva
Russian Academy of Sciences
3 shared publications
Latest Publications
- 10 August 2026
- Published by Taylor & Francis in Fullerenes, Nanotubes and Carbon Nanostructures
- p. 1-10
Analysis of CH groups of electrically conductive carbon black
Recently, the need of carbon black as a component of electrodes in various electrical devices has increased significantly.[1] This carbon material is widely used in lithium- and sodium-ion batterie...
- 10 August 2026
- Published by Taylor & Francis in Fullerenes, Nanotubes and Carbon Nanostructures
- p. 1-10
Analysis of CH groups of electrically conductive carbon black
Recently, the need of carbon black as a component of electrodes in various electrical devices has increased significantly.[1] This carbon material is widely used in lithium- and sodium-ion batterie...
- 1 October 2025
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 65 (10) , 1152-1159
The Efficiency of Fe/MFI Additives in Reducing NOx in Cracking Catalyst Regeneration Flue Gas
A series of additives based on an iron-modified MFI zeolite were investigated for their ability to reduce NOx in cracking catalyst regeneration flue gases. Their efficiency was dependent on the iron loading, the zeolite SiO2/Al2O3 ratio, and the initial cationic form used for modification. The Fe/MFI additives prepared from an NH4-form zeolite with a low SiO2/Al2O3 ratio (23) demonstrated excellent performance. Under industrially relevant catalyst regeneration conditions, the additive with an optimized iron oxide content (within a tested range of 0.5 to 2.5 wt %) reached a NOx reduction efficiency of 45.4%.
- 1 October 2025
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 65 (10) , 1152-1159
The Efficiency of Fe/MFI Additives in Reducing NOx in Cracking Catalyst Regeneration Flue Gas
A series of additives based on an iron-modified MFI zeolite were investigated for their ability to reduce NOx in cracking catalyst regeneration flue gases. Their efficiency was dependent on the iron loading, the zeolite SiO2/Al2O3 ratio, and the initial cationic form used for modification. The Fe/MFI additives prepared from an NH4-form zeolite with a low SiO2/Al2O3 ratio (23) demonstrated excellent performance. Under industrially relevant catalyst regeneration conditions, the additive with an optimized iron oxide content (within a tested range of 0.5 to 2.5 wt %) reached a NOx reduction efficiency of 45.4%.
- Open Access
- 3 September 2025
- Published by ITMO University in Nanosystems: Physics, Chemistry, Mathematics
- Vol. 16 (4) , 498-509
La and Co-based materials for ammonia decomposition: activity, stability and structural changes
The La0.9Sr0.1Sc0.9Co0.1O3-δ (LS) and La0.9Sr0.1CoO3-δ (LC) phases and composite materials based on them were synthesized. There are data in the literature on the activity of pure or modified forms of LC in ammonia decomposition, but there are no data on the activity of the LS phase and LS–LC composites. Therefore, the stability and activity of LS–LC composites and initial LS and LC in ammonia decomposition were investigated. The best result in the decomposition of ammonia at 700◦C and WHSV of 60000 ml NH3·g-1cat ·h-1 shows LC – 99%, the worst LS – 80%. Under the same conditions, the activity of samples LC, 40LS–60LC and 50LS–50LC remains unchanged for 40 hours. It was found that during ammonia decomposition, the LC phase decomposes to form cobalt and La(OH)3 nanoparticles, but the LS phase does not undergo significant changes, which is confirmed by X-ray diffraction, IR spectroscopy, Raman spectroscopy and TEM.
- 3 September 2025
- Published by ITMO University in Nanosystems: Physics, Chemistry, Mathematics
- Vol. 16 (4) , 498-509
Open AccessLa and Co-based materials for ammonia decomposition: activity, stability and structural changes
The La0.9Sr0.1Sc0.9Co0.1O3-δ (LS) and La0.9Sr0.1CoO3-δ (LC) phases and composite materials based on them were synthesized. There are data in the literature on the activity of pure or modified forms of LC in ammonia decomposition, but there are no data on the activity of the LS phase and LS–LC composites. Therefore, the stability and activity of LS–LC composites and initial LS and LC in ammonia decomposition were investigated. The best result in the decomposition of ammonia at 700◦C and WHSV of 60000 ml NH3·g-1cat ·h-1 shows LC – 99%, the worst LS – 80%. Under the same conditions, the activity of samples LC, 40LS–60LC and 50LS–50LC remains unchanged for 40 hours. It was found that during ammonia decomposition, the LC phase decomposes to form cobalt and La(OH)3 nanoparticles, but the LS phase does not undergo significant changes, which is confirmed by X-ray diffraction, IR spectroscopy, Raman spectroscopy and TEM.
- 24 September 2024
- Published by Springer Nature in Journal of Materials Science
- Vol. 59 (37) , 17517-17530
Influence of the structure of carbon black on its electrical conductivity and adsorption properties
- 24 September 2024
- Published by Springer Nature in Journal of Materials Science
- Vol. 59 (37) , 17517-17530
Influence of the structure of carbon black on its electrical conductivity and adsorption properties
- Open Access
- 1 August 2023
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 63 (8) , 982-992
Hydrogenation of Acetylene over Pd–Ag/Sibunit Catalysts: Effect of the Deposition Sequence of Active Component Precursors
The study investigates interactions between palladium and silver in Pd–Ag bimetallic catalysts supported on a mesoporous carbon material Sibunit and, in particular, the dependence of these interactions on the deposition sequence of the metal precursors. Using XRD and TEM results, it was shown that impregnating the support with an aqueous solution that contained nitrate salts of both metals, followed by hydrogen treatment at 500°C, generates uniformly sized Pd 0.6 Ag 0.4 particles ( d av = 5.6 nm). These particles exhibit high selectivity (79%) in the reaction of acetylene hydrogenation to ethylene. The catalysts synthesized by sequential impregnation of the support with solutions of Pd and Ag nitrates interleaved with heat treatment in H 2 exhibited a lower selectivity (68–73%) due to the formation of particles non-uniform both in composition and size (about 4 to 60 nm). The IR spectroscopy data suggest this effect is presumably associated with the removal of O-containing functional groups from the carbon surface during the reduction of the supported precursor. Given that O-groups act as anchoring sites for the precursors of active components and suppress the ability of Sibunit to reduce metals from their salt solutions, the subsequent deposition of the second metal salt causes a non-uniform distribution of this metal on the surface and the generation of larger particles.
- 1 August 2023
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 63 (8) , 982-992
Open AccessHydrogenation of Acetylene over Pd–Ag/Sibunit Catalysts: Effect of the Deposition Sequence of Active Component Precursors
The study investigates interactions between palladium and silver in Pd–Ag bimetallic catalysts supported on a mesoporous carbon material Sibunit and, in particular, the dependence of these interactions on the deposition sequence of the metal precursors. Using XRD and TEM results, it was shown that impregnating the support with an aqueous solution that contained nitrate salts of both metals, followed by hydrogen treatment at 500°C, generates uniformly sized Pd 0.6 Ag 0.4 particles ( d av = 5.6 nm). These particles exhibit high selectivity (79%) in the reaction of acetylene hydrogenation to ethylene. The catalysts synthesized by sequential impregnation of the support with solutions of Pd and Ag nitrates interleaved with heat treatment in H 2 exhibited a lower selectivity (68–73%) due to the formation of particles non-uniform both in composition and size (about 4 to 60 nm). The IR spectroscopy data suggest this effect is presumably associated with the removal of O-containing functional groups from the carbon surface during the reduction of the supported precursor. Given that O-groups act as anchoring sites for the precursors of active components and suppress the ability of Sibunit to reduce metals from their salt solutions, the subsequent deposition of the second metal salt causes a non-uniform distribution of this metal on the surface and the generation of larger particles.
- 6 May 2023
- Published by Elsevier in Best Practice & Research Clinical Obstetrics & Gynaecology
- Vol. 88, 102346
Detoxification treatment in Gynecology using a modified molded sorbent
- 6 May 2023
- Published by Elsevier in Best Practice & Research Clinical Obstetrics & Gynaecology
- Vol. 88, 102346
Detoxification treatment in Gynecology using a modified molded sorbent
- Open Access
Ceria–Zirconia-Supported Ruthenium Catalysts for Hydrogen Production by Ammonia Decomposition
Commercial cerium–zirconium oxide supports (Ce0.5Zr0.5O2, Ce0.75Zr0.25O2, and Ce0.4Zr0.5Y0.05La0.05O2) were used to prepare Ru/CeZrOx catalysts. According to the XRD and IR spectroscopy data, the supports consist of ceria-based substitutional solid solutions. The specific surface areas of supports and catalysts are similar and range from 71–89 m2/g. As shown by TEM and XRD methods, the size of support particles equals 6–11 nm. According to the TEM data, the size of ruthenium particles does not exceed 1.3 nm. The catalyst activity in the ammonia decomposition process was studied. The Ru/Ce0.75Zr0.25O2 catalyst at temperature 500 °C and GHSV 120,000 h−1 demonstrated the highest hydrogen productivity of 53.3 mmol H2/(gcat·min) and compares well with the best results reported in the literature. The kinetics of ammonia decomposition reaction were calculated using the Temkin–Pyzhov exponential expression. The developed mathematical model well described the experimental data. The studied catalysts demonstrated high activity for the ammonia decomposition reaction.
Open AccessCeria–Zirconia-Supported Ruthenium Catalysts for Hydrogen Production by Ammonia Decomposition
Commercial cerium–zirconium oxide supports (Ce0.5Zr0.5O2, Ce0.75Zr0.25O2, and Ce0.4Zr0.5Y0.05La0.05O2) were used to prepare Ru/CeZrOx catalysts. According to the XRD and IR spectroscopy data, the supports consist of ceria-based substitutional solid solutions. The specific surface areas of supports and catalysts are similar and range from 71–89 m2/g. As shown by TEM and XRD methods, the size of support particles equals 6–11 nm. According to the TEM data, the size of ruthenium particles does not exceed 1.3 nm. The catalyst activity in the ammonia decomposition process was studied. The Ru/Ce0.75Zr0.25O2 catalyst at temperature 500 °C and GHSV 120,000 h−1 demonstrated the highest hydrogen productivity of 53.3 mmol H2/(gcat·min) and compares well with the best results reported in the literature. The kinetics of ammonia decomposition reaction were calculated using the Temkin–Pyzhov exponential expression. The developed mathematical model well described the experimental data. The studied catalysts demonstrated high activity for the ammonia decomposition reaction.
- 16 December 2022
- Published by Pleiades Publishing Ltd in Catalysis in Industry
- Vol. 14 (4) , 363-368
Creating a Heterohomogeneous Catalytic System for the Alkylation of Benzene with Ethylene through the Reaction beteen Carbon Tetrachloride and Aluminum Alloys
The in situ formation of a catalytic heterohomogeneous system containing Al–M alloy (M is Ni, Co, Cu) and Al(M)/Cl complex in a benzene–ethylene medium at a temperature of 80°C and a pressure of 0.2–0.3 MPa is studied. The characteristic patterns of interaction between Al–M alloys activated with a liquid metal Ga–In eutectic and a chlorinating agent (CCl4) with the formation of catalytically active metal–aluminum chloride Al(M)/Cl complexes are established. Results from spectrokinetic measurements show the order of the reactivity of activated alloys with respect to excess CCl4 is Al–Cu ≈ Al–Ni > Al > Al–Co. The highest catalytic activity is displayed by nickel–aluminum chloride complexes whose selectivity toward ethylbenzene is 48%. Data from IR and UV-VIS spectroscopy show that the structure and composition of metal chloride complexes formed in situ in the aromatic reaction medium is determined by a combination of coupled ionic pairs \([{\text{AlC}}{{{\text{l}}}_{4}}]_{{{\text{tetr}}}}^{ - }{\text{/[NiC}}{{{\text{l}}}_{{\text{6}}}}]_{{{\text{oct}}}}^{{4-}}\) and \(\left[ {{\text{AlC}}{{{\text{l}}}_{{\text{4}}}}} \right]_{{{\text{tetr}}}}^{ - }/\left[ {{\text{CuC}}{{{\text{l}}}_{{\text{2}}}}} \right]_{{{\text{lin}}}}^{ - }\), which are stabilized by (C6H5)3C+ carbocation.- 16 December 2022
- Published by Pleiades Publishing Ltd in Catalysis in Industry
- Vol. 14 (4) , 363-368
Creating a Heterohomogeneous Catalytic System for the Alkylation of Benzene with Ethylene through the Reaction beteen Carbon Tetrachloride and Aluminum Alloys
The in situ formation of a catalytic heterohomogeneous system containing Al–M alloy (M is Ni, Co, Cu) and Al(M)/Cl complex in a benzene–ethylene medium at a temperature of 80°C and a pressure of 0.2–0.3 MPa is studied. The characteristic patterns of interaction between Al–M alloys activated with a liquid metal Ga–In eutectic and a chlorinating agent (CCl4) with the formation of catalytically active metal–aluminum chloride Al(M)/Cl complexes are established. Results from spectrokinetic measurements show the order of the reactivity of activated alloys with respect to excess CCl4 is Al–Cu ≈ Al–Ni > Al > Al–Co. The highest catalytic activity is displayed by nickel–aluminum chloride complexes whose selectivity toward ethylbenzene is 48%. Data from IR and UV-VIS spectroscopy show that the structure and composition of metal chloride complexes formed in situ in the aromatic reaction medium is determined by a combination of coupled ionic pairs \([{\text{AlC}}{{{\text{l}}}_{4}}]_{{{\text{tetr}}}}^{ - }{\text{/[NiC}}{{{\text{l}}}_{{\text{6}}}}]_{{{\text{oct}}}}^{{4-}}\) and \(\left[ {{\text{AlC}}{{{\text{l}}}_{{\text{4}}}}} \right]_{{{\text{tetr}}}}^{ - }/\left[ {{\text{CuC}}{{{\text{l}}}_{{\text{2}}}}} \right]_{{{\text{lin}}}}^{ - }\), which are stabilized by (C6H5)3C+ carbocation.- 1 January 2018
- Published by Ivanovo State University of Chemistry and Technology in ChemChemTech
- Vol. 61 (9-10) , 64-69
INTERACTION OF ALUMINUM-COBALT AND ALUMINUM-NICKEL ALLOYS ACTIVATED BY LIQUID GALLIUM-INDIUM EUTECTIC WITH TERT-BUTYL CHLORIDE FOR FORMATION OF CATALYTIC METAL - ALUMO-CHLORIDE COMPLEXES
It is known that binary alloys of aluminum and metals of the iron group (cobalt, nickel) after their activation with the liquid eutectic gallium-indium by the removal of "passivating" oxide layers sharply increase the reactivity with respect to organochlorines. Corresponding reactions lead to the formation of metal-alumo-chloride complexes as inorganic products, which are active in many practically important catalytic reactions of liquid-phase conversion of hydrocarbons such as: alkylation, isomerization, oligomerization. This approach which was previously developed by the authors for the polycrystalline aluminum, is of interest in metal-complex catalysis since the formation of catalytic alumo-chloride and/or metal-alumo-chloride complexes can be carried out directly in the reaction medium, i.e. in situ. In this work, the local composition, structure and morphology of surface layers of aluminum-cobalt and aluminum-nickel alloys activated with liquid gallium-indium eutectic were studied using the methods of scanning electron microscopy and X-ray energy-dispersive spectrometry to determine the physicochemical regularities of the dynamics of their interaction with tert-butyl chloride at room temperatures. The formation of metal chloride complexes in the interphase area "activated alloy - tert-butyl chloride" was studied by ATR-FT-IR method in situ. The results obtained indicate that mono- and bi- nuclear alumo-chloride anions stabilized by cobalt and nickel cations are formed during the interaction. It is assumed that the ionic complex pairs formed are the active centers in liquid-phase reactions of hydrocarbons transformation at low temperatures. These structures are responsible for significantly change in the selectivity of catalytic processes compared to aluminum chloride catalyst.
- 1 January 2018
- Published by Ivanovo State University of Chemistry and Technology in ChemChemTech
- Vol. 61 (9-10) , 64-69
INTERACTION OF ALUMINUM-COBALT AND ALUMINUM-NICKEL ALLOYS ACTIVATED BY LIQUID GALLIUM-INDIUM EUTECTIC WITH TERT-BUTYL CHLORIDE FOR FORMATION OF CATALYTIC METAL - ALUMO-CHLORIDE COMPLEXES
It is known that binary alloys of aluminum and metals of the iron group (cobalt, nickel) after their activation with the liquid eutectic gallium-indium by the removal of "passivating" oxide layers sharply increase the reactivity with respect to organochlorines. Corresponding reactions lead to the formation of metal-alumo-chloride complexes as inorganic products, which are active in many practically important catalytic reactions of liquid-phase conversion of hydrocarbons such as: alkylation, isomerization, oligomerization. This approach which was previously developed by the authors for the polycrystalline aluminum, is of interest in metal-complex catalysis since the formation of catalytic alumo-chloride and/or metal-alumo-chloride complexes can be carried out directly in the reaction medium, i.e. in situ. In this work, the local composition, structure and morphology of surface layers of aluminum-cobalt and aluminum-nickel alloys activated with liquid gallium-indium eutectic were studied using the methods of scanning electron microscopy and X-ray energy-dispersive spectrometry to determine the physicochemical regularities of the dynamics of their interaction with tert-butyl chloride at room temperatures. The formation of metal chloride complexes in the interphase area "activated alloy - tert-butyl chloride" was studied by ATR-FT-IR method in situ. The results obtained indicate that mono- and bi- nuclear alumo-chloride anions stabilized by cobalt and nickel cations are formed during the interaction. It is assumed that the ionic complex pairs formed are the active centers in liquid-phase reactions of hydrocarbons transformation at low temperatures. These structures are responsible for significantly change in the selectivity of catalytic processes compared to aluminum chloride catalyst.
- 1 December 2017
- Published by Pleiades Publishing Ltd in Russian Journal of Applied Chemistry
- Vol. 90 (12) , 1926-1930
In Situ Formation of Al(Fe)/Cl Metal Chloride Complexes and Evaluation of Their Catalytic Properties in the Reaction of Ethylene Oligomerization
According to FT-IR and UV spectroscopic data, the interaction of the Al/Fe alloy with tert-butyl chloride results in that AlCl4–, Al2Cl7–, and FeCl2+ ion complexes, Fe3+ ions, and AlCl3molecular...
- 1 December 2017
- Published by Pleiades Publishing Ltd in Russian Journal of Applied Chemistry
- Vol. 90 (12) , 1926-1930
In Situ Formation of Al(Fe)/Cl Metal Chloride Complexes and Evaluation of Their Catalytic Properties in the Reaction of Ethylene Oligomerization
According to FT-IR and UV spectroscopic data, the interaction of the Al/Fe alloy with tert-butyl chloride results in that AlCl4–, Al2Cl7–, and FeCl2+ ion complexes, Fe3+ ions, and AlCl3molecular...