Zhenfeng Gu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Zhenfeng Gu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Bo Tao
State Key Laboratory of Intelligent Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China
6 shared publications - Zeyu Gong
Huazhong University of Science and Technology
6 shared publications - Han Ding
Huazhong University of Science and Technology
5 shared publications - Ke Tan
State Key Laboratory of Intelligent Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China
5 shared publications - Ying Shi
State Key Laboratory of Intelligent Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China
4 shared publications - Chong Wu
State Key Laboratory of Intelligent Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China
2 shared publications
Latest Publications
- 20 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Automation Science and Engineering
- Vol. 22 (15455955) , 11264-11275
LESO-Based NMPC Tracking Control of Climbing Robot on Large Components With Variable Curvature
Wheeled climbing robots have great application prospects in the machining of large components with variable curvature. However, its accurate motion control on variable curvature surfaces faces two fatal challenges. The varied contact states between the robot’s wheels and the variable curvature surfaces make it difficult to establish an accurate kinematics model. Additionally, there exists a different degree of robot slippage when the robot moves in different attitudes due to the dragging effect of gravity. To overcome the above problems, we first present a kinematics modeling method with instantaneous plane constraints on a variable curvature surface. Subsequently, a linear extended state observer (LESO)-based nonlinear model predictive control (NMPC) scheme is designed, in which the NMPC is used to calculate the nominal control inputs and the LESO is used to estimate and compensate for lumped disturbance brought by the robot slippage and surface constraints. Experiments on a real wind turbine blade with variable curvature show that the proposed control scheme can well eliminate the influence of lumped disturbance, and the climbing robots can achieve unbiased (AVG < 0.1 mm) and high-precision (RMSE < 2 mm) trajectory tracking. provides a solution for automatic and high-precision trajectory tracking for climbing robot with localization system in factories, offering the potential for high-quality machining of large components.
- 20 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Automation Science and Engineering
- Vol. 22 (15455955) , 11264-11275
LESO-Based NMPC Tracking Control of Climbing Robot on Large Components With Variable Curvature
Wheeled climbing robots have great application prospects in the machining of large components with variable curvature. However, its accurate motion control on variable curvature surfaces faces two fatal challenges. The varied contact states between the robot’s wheels and the variable curvature surfaces make it difficult to establish an accurate kinematics model. Additionally, there exists a different degree of robot slippage when the robot moves in different attitudes due to the dragging effect of gravity. To overcome the above problems, we first present a kinematics modeling method with instantaneous plane constraints on a variable curvature surface. Subsequently, a linear extended state observer (LESO)-based nonlinear model predictive control (NMPC) scheme is designed, in which the NMPC is used to calculate the nominal control inputs and the LESO is used to estimate and compensate for lumped disturbance brought by the robot slippage and surface constraints. Experiments on a real wind turbine blade with variable curvature show that the proposed control scheme can well eliminate the influence of lumped disturbance, and the climbing robots can achieve unbiased (AVG < 0.1 mm) and high-precision (RMSE < 2 mm) trajectory tracking. provides a solution for automatic and high-precision trajectory tracking for climbing robot with localization system in factories, offering the potential for high-quality machining of large components.
- 19 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (7) , 7200-7209
A Differential Geometry Modeling Method for Wheeled Climbing Robots Tracking Control on Variable Curvature Surfaces
Wheeled climbing robots equipped with tools can achieve high-coverage machining of large components with free-form surfaces. Trajectory tracking is the foundation for machining. However, there is a lack of a universal yet accurate model for robots while moving on variable curvature surfaces, making it difficult to guarantee tracking performance. Thus, this article proposes a universal contact frame based on differential geometry and establishes a kinematics model that uses surface parameters as state variables for robots moving on variable curvature surfaces. Based on this model, a tracking controller utilizing surface parameters error is then designed, enabling it to be applicable for tracking of climbing robots on free-form surfaces. Experiments with a wheeled climbing robot on a portion of a real wind turbine blade with a radius of more than 1.1 m demonstrate the effectiveness of the proposed method, with a root mean squared error (RMSE) of tracking accuracy of less than 1 mm.
- 19 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (7) , 7200-7209
A Differential Geometry Modeling Method for Wheeled Climbing Robots Tracking Control on Variable Curvature Surfaces
Wheeled climbing robots equipped with tools can achieve high-coverage machining of large components with free-form surfaces. Trajectory tracking is the foundation for machining. However, there is a lack of a universal yet accurate model for robots while moving on variable curvature surfaces, making it difficult to guarantee tracking performance. Thus, this article proposes a universal contact frame based on differential geometry and establishes a kinematics model that uses surface parameters as state variables for robots moving on variable curvature surfaces. Based on this model, a tracking controller utilizing surface parameters error is then designed, enabling it to be applicable for tracking of climbing robots on free-form surfaces. Experiments with a wheeled climbing robot on a portion of a real wind turbine blade with a radius of more than 1.1 m demonstrate the effectiveness of the proposed method, with a root mean squared error (RMSE) of tracking accuracy of less than 1 mm.
- 4 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (5) , 5032-5040
An Optimal Adsorption Force Planning Method for Wheeled Climbing Robot on Large Components With Curved Surfaces
The wheeled negative pressure adsorption climbing robots possess unique advantages for processing extra-large components due to the surface adsorption and motion ability. The large components usually have complex variable curvature surfaces, significantly amplifying the propensity for wheel slip of climbing robots. An adsorption forces planning method was proposed to restrain the slip and then approach stable motion. To address adsorption forces planning demand, we propose a motion performance indicator associated with the wheels’ slip, and establish a dynamic model based on the nonlinear tire model, revealing the quantified effect of adsorption forces on slip ratios. Furthermore, a constrained optimization problem is established to solve optimal adsorption forces using the particle swarm optimization. The proposed method has been validated adequately on a part of a large wind turbine blade, which is a typical large component with variable curvature. The results show a great performance upgrade, the average and the standard deviation of the slip ratios were reduced by 73% and 70% at maximum, respectively. Additionally, the error of yaw angles was reduced by 84% at maximum. The experiment demonstrates the proposed method greatly improves motion performance.
- 4 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (5) , 5032-5040
An Optimal Adsorption Force Planning Method for Wheeled Climbing Robot on Large Components With Curved Surfaces
The wheeled negative pressure adsorption climbing robots possess unique advantages for processing extra-large components due to the surface adsorption and motion ability. The large components usually have complex variable curvature surfaces, significantly amplifying the propensity for wheel slip of climbing robots. An adsorption forces planning method was proposed to restrain the slip and then approach stable motion. To address adsorption forces planning demand, we propose a motion performance indicator associated with the wheels’ slip, and establish a dynamic model based on the nonlinear tire model, revealing the quantified effect of adsorption forces on slip ratios. Furthermore, a constrained optimization problem is established to solve optimal adsorption forces using the particle swarm optimization. The proposed method has been validated adequately on a part of a large wind turbine blade, which is a typical large component with variable curvature. The results show a great performance upgrade, the average and the standard deviation of the slip ratios were reduced by 73% and 70% at maximum, respectively. Additionally, the error of yaw angles was reduced by 84% at maximum. The experiment demonstrates the proposed method greatly improves motion performance.
- 23 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 29 (6) , 4099-4109
A Climbing Machining Robot for Large Components With Variable Curvature Surface
This article proposes a climbing machining robot that can adsorb and move on the variable curvature surface of large and complex components to perform machining tasks. Active compliance suction units, which consist of twofold innovation, are proposed for this robot to overcome the bottleneck involving adsorption on the variable curvature surface. To solve the dilemma between high vacuum tolerance and surface compliance capability, we designed a novel trachea-inspired anisotropic stiffness sealing lip for the suction chamber, and it showed flexibility in the adsorption direction for adoption to complex surfaces and presented a high stiffness that can withstand large vacuum forces at its sides. Furthermore, to avoid vacuum leaks due to overstretching and overcompressing of the sealing lip, we developed an active compliance actuator to align the axis direction of the suction chamber with the normal direction of the adsorbed surface and maintain a suitable distance. To meeting strict weight and dimension demands, the actuator innovatively combines cable-driven units and 3-revolute-revolute-spherical parallel mechanism to reach a high load/weight ratio. The prototype of the climbing machining robot was developed and tested on a real large wind-turbine blade with variable curvatures ranging from 1 to 15 m. The experimental results show that the 10 kg-weight climbing machining robot with three ACSUs can provide over 1000 N adsorption force in total, and the fluctuation of adsorption forces can be reduced by 96% compared with that of robots with traditional pure passive compliance suction units. A comparative polishing experiment was executed on different curvature regions of the wind turbine blade, and the results prove that the proposed method can apply uniform polishing. In addition, a polishing-quality verification experiment was realized using the proposed climbing machining robot with a force-controlled polisher. These polishing experiments proved the machining capability of the proposed climbing robot.
- 23 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 29 (6) , 4099-4109
A Climbing Machining Robot for Large Components With Variable Curvature Surface
This article proposes a climbing machining robot that can adsorb and move on the variable curvature surface of large and complex components to perform machining tasks. Active compliance suction units, which consist of twofold innovation, are proposed for this robot to overcome the bottleneck involving adsorption on the variable curvature surface. To solve the dilemma between high vacuum tolerance and surface compliance capability, we designed a novel trachea-inspired anisotropic stiffness sealing lip for the suction chamber, and it showed flexibility in the adsorption direction for adoption to complex surfaces and presented a high stiffness that can withstand large vacuum forces at its sides. Furthermore, to avoid vacuum leaks due to overstretching and overcompressing of the sealing lip, we developed an active compliance actuator to align the axis direction of the suction chamber with the normal direction of the adsorbed surface and maintain a suitable distance. To meeting strict weight and dimension demands, the actuator innovatively combines cable-driven units and 3-revolute-revolute-spherical parallel mechanism to reach a high load/weight ratio. The prototype of the climbing machining robot was developed and tested on a real large wind-turbine blade with variable curvatures ranging from 1 to 15 m. The experimental results show that the 10 kg-weight climbing machining robot with three ACSUs can provide over 1000 N adsorption force in total, and the fluctuation of adsorption forces can be reduced by 96% compared with that of robots with traditional pure passive compliance suction units. A comparative polishing experiment was executed on different curvature regions of the wind turbine blade, and the results prove that the proposed method can apply uniform polishing. In addition, a polishing-quality verification experiment was realized using the proposed climbing machining robot with a force-controlled polisher. These polishing experiments proved the machining capability of the proposed climbing robot.
- 3 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 19 (12) , 11765-11775
RF-SLAM: UHF-RFID Based Simultaneous Tags Mapping and Robot Localization Algorithm for Smart Warehouse Position Service
In this article, we propose an RFID-based simultaneous localization and mapping (RF-SLAM) method that allows us, for the first time, to estimate the robot's position and the tags’ 3D position in the warehouse environment simultaneously without any reference tags and external sensors, using only COTS RFID device. RF-SLAM is designed to transform the RFID measurement into the relative tag position constraint and use a corresponding graph based model to solve the SLAM problem. Specifically, a multiantenna-based relative localization method using phase measurement and odometer data in a short time is proposed as the front end. The back end is a novel graph model based on the relative tags position constraint and odometer constraint. Experiments in different types of warehouses show the localization accuracy of robot and tags’ 3D position is about 5 cm and 10 cm, respectively. The experimental results in a more challenging and actual environment are still competitive.
- 3 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 19 (12) , 11765-11775
RF-SLAM: UHF-RFID Based Simultaneous Tags Mapping and Robot Localization Algorithm for Smart Warehouse Position Service
In this article, we propose an RFID-based simultaneous localization and mapping (RF-SLAM) method that allows us, for the first time, to estimate the robot's position and the tags’ 3D position in the warehouse environment simultaneously without any reference tags and external sensors, using only COTS RFID device. RF-SLAM is designed to transform the RFID measurement into the relative tag position constraint and use a corresponding graph based model to solve the SLAM problem. Specifically, a multiantenna-based relative localization method using phase measurement and odometer data in a short time is proposed as the front end. The back end is a novel graph model based on the relative tags position constraint and odometer constraint. Experiments in different types of warehouses show the localization accuracy of robot and tags’ 3D position is about 5 cm and 10 cm, respectively. The experimental results in a more challenging and actual environment are still competitive.
- 12 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 19 (5) , 6762-6772
Global Localization Based on Tether and Visual-Inertial Odometry With Adsorption Constraints for Climbing Robots
Localization in a large-scale 3D scene is a key challenge faced by climbing robots on large workpieces. This paper proposes a global localization method for climbing robots based on tether displacement sensor, visual-inertial odometry (VIO), and Computer-Aided Design (CAD) model of workpieces. Tether displacement sensor measures the distance between robot and tether anchor with little drift, which enables robot to acquire global pose. Adsorption constraints on robot motion are extracted using CAD model to reduce the drift of VIO. The approach realizes global localization with high accuracy for the robots when climbing on large workpieces without other external locating equipment. The performance is verified with a prototype of climbing robot testing on real large workpieces. In all experiments, our method with adsorption constraints outperforms existing visual-inertial odometry. The largest drift of merged trajectory is as low as 0.51% in global localization on a wind turbine blade with length of 8m.
- 12 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Informatics
- Vol. 19 (5) , 6762-6772
Global Localization Based on Tether and Visual-Inertial Odometry With Adsorption Constraints for Climbing Robots
Localization in a large-scale 3D scene is a key challenge faced by climbing robots on large workpieces. This paper proposes a global localization method for climbing robots based on tether displacement sensor, visual-inertial odometry (VIO), and Computer-Aided Design (CAD) model of workpieces. Tether displacement sensor measures the distance between robot and tether anchor with little drift, which enables robot to acquire global pose. Adsorption constraints on robot motion are extracted using CAD model to reduce the drift of VIO. The approach realizes global localization with high accuracy for the robots when climbing on large workpieces without other external locating equipment. The performance is verified with a prototype of climbing robot testing on real large workpieces. In all experiments, our method with adsorption constraints outperforms existing visual-inertial odometry. The largest drift of merged trajectory is as low as 0.51% in global localization on a wind turbine blade with length of 8m.