Min Wei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Min Wei has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Yuehui Gao
College of Physics, University of Electronic Science and Technology, Chengdu, China
3 shared publications - Junlin Wang
Inner Mongolia University
2 shared publications - Tao Liu
College of Electronic Information Engineering, Inner Mongolia University, Hohhot, China
2 shared publications Xin Wang
College of Electronic Information Engineering, Inner Mongolia University, Hohhot, China
2 shared publications- Yuhang Lu
College of Electronic Information Engineering, Inner Mongolia University, Hohhot, China
2 shared publications Junlin Wang
College of Electronic Information Engineering, Inner Mongolia University, Hohhot, China
1 shared publication
Latest Publications
- 15 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (8) , 2326-2330
Extremely Low-Profile Micro Dual-Band Patch Antenna for 5G Mobile Terminals
In this letter, a extremely low profile dual-band patch antenna is proposed for 5G terminal applications. Target bands are part of the 5G N78 band (3.4-3.6 GHz) and part of the 5G N79 band (4.8-5.0 GHz). Use the two resonant modes of the half-mode patch and adjust their size to separate the resonant frequencies. Loads parasitic patches to extend their efficiency and impedance bandwidths. In order to make the antenna occupy less space, two pairs of perpendicular slots are etched in the middle of the antenna to extend the current path and reduce the resonance frequencies. The average efficiency of the designed antenna is higher than most of the reported patch antennas. Physical fabrication and device testing were performed to prove the feasibility of the proposed antenna.
- 15 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (8) , 2326-2330
Extremely Low-Profile Micro Dual-Band Patch Antenna for 5G Mobile Terminals
In this letter, a extremely low profile dual-band patch antenna is proposed for 5G terminal applications. Target bands are part of the 5G N78 band (3.4-3.6 GHz) and part of the 5G N79 band (4.8-5.0 GHz). Use the two resonant modes of the half-mode patch and adjust their size to separate the resonant frequencies. Loads parasitic patches to extend their efficiency and impedance bandwidths. In order to make the antenna occupy less space, two pairs of perpendicular slots are etched in the middle of the antenna to extend the current path and reduce the resonance frequencies. The average efficiency of the designed antenna is higher than most of the reported patch antennas. Physical fabrication and device testing were performed to prove the feasibility of the proposed antenna.
- 27 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (6) , 1834-1838
Low-Profile Dual-Band Microstrip Patch Antenna With Shorting Pins
A single-layer low-profile dual-band patch antenna is proposed in this paper. A Π-shaped slot is engraved on the radiating patch, separating it into a main patch and a parasitic patch to achieve the dual-band characteristics. The purpose of loading five shorting pins between the two vertical slots on the main patch is to turn down the two frequencies, which can generate TM01 mode and TM11 mode. To improve the impedance matching in the lower band and broaden the dual-band bandwidth, four shorting pins are placed on the edge of the long side of the parasitic patch, which can excite the TM10 mode. The combination of the TM01, TM11 and TM10 modes achieves the 3.45∼3.7 GHz and 4.7∼5.33 GHz dual-band. Manufacturing and measuring a prototype. The results of the measurements indicate that the antenna achieves a dual-band with reflection coefficient less than -6dB which are 3.5∼3.75 GHz (250 MHz, 7.0%) and 4.73∼5.41 GHz (680 MHz, 13.4%) with peak gains of 6.23 dB and 5.06 dB in the low and high bands, respectively. The average total efficiencies in the dual bands are 64.2% and 77.3%, respectively.
- 27 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (6) , 1834-1838
Low-Profile Dual-Band Microstrip Patch Antenna With Shorting Pins
A single-layer low-profile dual-band patch antenna is proposed in this paper. A Π-shaped slot is engraved on the radiating patch, separating it into a main patch and a parasitic patch to achieve the dual-band characteristics. The purpose of loading five shorting pins between the two vertical slots on the main patch is to turn down the two frequencies, which can generate TM01 mode and TM11 mode. To improve the impedance matching in the lower band and broaden the dual-band bandwidth, four shorting pins are placed on the edge of the long side of the parasitic patch, which can excite the TM10 mode. The combination of the TM01, TM11 and TM10 modes achieves the 3.45∼3.7 GHz and 4.7∼5.33 GHz dual-band. Manufacturing and measuring a prototype. The results of the measurements indicate that the antenna achieves a dual-band with reflection coefficient less than -6dB which are 3.5∼3.75 GHz (250 MHz, 7.0%) and 4.73∼5.41 GHz (680 MHz, 13.4%) with peak gains of 6.23 dB and 5.06 dB in the low and high bands, respectively. The average total efficiencies in the dual bands are 64.2% and 77.3%, respectively.
- 20 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (5) , 1020-1024
A Low-Profile Broadband Multimode Patch Antenna for 5G Mobile Applications
A low profile broadband multimode patch antenna is proposed for 5G mobile applications. The proposed antenna is made up of a single metal patch, a FR-4 dielectric substrate layer, an air cavity, and eight metal pins. The patch can form a magnetic wall by adding the eight metal pins, which can also generate a pair of TM 1/2,0 modes and TM 10 mode. Based on these modes, two narrow rectangles with 0.169λ (about 0.011λ at 3.9 GHz) are etched on the patch, which can simultaneously form two kinds of new modes (TM 1/2,1 and TM 1/2,2 ) to achieve the broadband operation (3.3∼4.2 GHz). To ensure the accuracy of this principle, the antenna sample is made and measured. The measured outcomes are in good accordance with the simulated ones, and the sample can still operate at 3.3∼4.2 GHz, covering the 5G N77 band. The in-band total efficiency can reach up to -0.491 dB (89.3%). The maximum gain in the entire band is 9.4 dB.
- 20 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 22 (5) , 1020-1024
A Low-Profile Broadband Multimode Patch Antenna for 5G Mobile Applications
A low profile broadband multimode patch antenna is proposed for 5G mobile applications. The proposed antenna is made up of a single metal patch, a FR-4 dielectric substrate layer, an air cavity, and eight metal pins. The patch can form a magnetic wall by adding the eight metal pins, which can also generate a pair of TM 1/2,0 modes and TM 10 mode. Based on these modes, two narrow rectangles with 0.169λ (about 0.011λ at 3.9 GHz) are etched on the patch, which can simultaneously form two kinds of new modes (TM 1/2,1 and TM 1/2,2 ) to achieve the broadband operation (3.3∼4.2 GHz). To ensure the accuracy of this principle, the antenna sample is made and measured. The measured outcomes are in good accordance with the simulated ones, and the sample can still operate at 3.3∼4.2 GHz, covering the 5G N77 band. The in-band total efficiency can reach up to -0.491 dB (89.3%). The maximum gain in the entire band is 9.4 dB.