İmRen Ozturk Yilmaz
İmRen Ozturk Yilmaz has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Abdullah Bi̇lİcİ
Beycelik Gestamp A.Ş.
1 shared publication - Hakan Aydin
Bursa Uludag Universitesi
1 shared publication - Mumin Yilmaz
Department of Mechanical Engineering, Bursa Technical University, Bursa 16310, Turkey
1 shared publication - Onur Saray
Karadeniz Technical University
1 shared publication
Latest Publications
- 19 April 2026
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 14 (2) , 340-351
The Effects of Electric Resistance Spot Welding on the Microstructure and Mechanical Properties of CR3 and Coated TBF Steel Sheets
This study investigates the resistance spot welding behavior of dissimilar low-carbon CR3 steel and coated transformation-induced plasticity-aided bainitic ferrite (TBF) steel sheets widely used in automotive body applications. The effects of welding current (6-7-8-9 kA) and welding time (240–400 ms) on weld microstructure, nugget size, indentation depth, and mechanical performance were systematically examined. Metallographic analysis revealed no macroscopic weld defects; however, limited mixing was observed in the fusion zone, particularly at lower heat inputs. Increasing heat input enhanced material mixing and widened the heat-affected zone (HAZ), especially on the TBF side, but also promoted liquid metal embrittlement (LME)-induced surface microcracks associated with Zn-coating penetration along grain boundaries. The maximum nugget size reached 8.34 mm at 9 kA–400 ms, while the indentation depth remained within automotive acceptance limits, with a maximum value of 21.65%. Tensile-shear tests showed that all fractures occurred in the HAZ of the thinner CR3 sheet in a tearing mode, with a maximum failure load of 4.25 kN at 7 kA–240 ms. Despite the presence of microcracks in the TBF HAZ, the joint strength was governed by the lower-strength CR3 sheet. The results highlight the importance of optimized welding parameters to balance sufficient nugget growth and minimize LME susceptibility in dissimilar advanced high-strength steel (AHSS)–mild steel combinations.
- 19 April 2026
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 14 (2) , 340-351
The Effects of Electric Resistance Spot Welding on the Microstructure and Mechanical Properties of CR3 and Coated TBF Steel Sheets
This study investigates the resistance spot welding behavior of dissimilar low-carbon CR3 steel and coated transformation-induced plasticity-aided bainitic ferrite (TBF) steel sheets widely used in automotive body applications. The effects of welding current (6-7-8-9 kA) and welding time (240–400 ms) on weld microstructure, nugget size, indentation depth, and mechanical performance were systematically examined. Metallographic analysis revealed no macroscopic weld defects; however, limited mixing was observed in the fusion zone, particularly at lower heat inputs. Increasing heat input enhanced material mixing and widened the heat-affected zone (HAZ), especially on the TBF side, but also promoted liquid metal embrittlement (LME)-induced surface microcracks associated with Zn-coating penetration along grain boundaries. The maximum nugget size reached 8.34 mm at 9 kA–400 ms, while the indentation depth remained within automotive acceptance limits, with a maximum value of 21.65%. Tensile-shear tests showed that all fractures occurred in the HAZ of the thinner CR3 sheet in a tearing mode, with a maximum failure load of 4.25 kN at 7 kA–240 ms. Despite the presence of microcracks in the TBF HAZ, the joint strength was governed by the lower-strength CR3 sheet. The results highlight the importance of optimized welding parameters to balance sufficient nugget growth and minimize LME susceptibility in dissimilar advanced high-strength steel (AHSS)–mild steel combinations.
- 28 February 2022
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 37 (2) , 609-624
Elektrik direnç punta kaynağı ile birleştirilen TBF/DP600 çeliklerinin mikroyapı ve mekanik özelliklerinin incelenmesi
In the study, the effects of welding parameters on microstructure and mechanical properties of electrical resistance spot welded TBF/DP600 steel sheets of 1.2 mm thickness were investigated. TBF steel used in the study was welded both with and without electro-galvanized. Microhardness measurements and tensile shear tests were taken as basis in determining the mechanical properties, while optical microscope was used for microstructural characterization. The nugget size of the spot-welded samples was determined by image processing technique, while the indentation depths at the electrode pressure points of the samples were measured by ultrasonic technique. It was observed from the fusion zone microstructure images that the two steels did not mix completely. Increasing the welding current and welding time increased the mixing ratio in fusion zone, expanded the heat affected zone and increased the nugget size, indentation depth and load bearing capacity. TBF steel was more affected by the thermal cycle during welding than DP600 steel. At high heat input, liquid metal embrittlement based microcrack formations initiating from the surface in the heat affected zone of galvanized TBF steels were observed, while corrosion started rapidly in the welding region of ungalvanized TBF steels. The highest hardness values were observed in ITAB on the TBF steel side. However, a significant softening occurred in the transition zone between the ITAB and base metal on the TBF steel side. The nugget size, indentation depth and load bearing capacity were found to be relatively higher in the galvanized TBF steel group. In dissimilar electrical resistance spot welded TBF/DP600 steel sheets having the same thickness, DP600 steel with lower strength has determined the welding strength. In high heat input during welding process, fractures are of the fusion zone button type with higher welding strength, while fractures are of partial fusion zone button type with lower welding strength in low heat input. If TBF steel is galvanized, relatively higher welding strength was obtained in the welding parameters that provide relatively lower heat input.
- 28 February 2022
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 37 (2) , 609-624
Elektrik direnç punta kaynağı ile birleştirilen TBF/DP600 çeliklerinin mikroyapı ve mekanik özelliklerinin incelenmesi
In the study, the effects of welding parameters on microstructure and mechanical properties of electrical resistance spot welded TBF/DP600 steel sheets of 1.2 mm thickness were investigated. TBF steel used in the study was welded both with and without electro-galvanized. Microhardness measurements and tensile shear tests were taken as basis in determining the mechanical properties, while optical microscope was used for microstructural characterization. The nugget size of the spot-welded samples was determined by image processing technique, while the indentation depths at the electrode pressure points of the samples were measured by ultrasonic technique. It was observed from the fusion zone microstructure images that the two steels did not mix completely. Increasing the welding current and welding time increased the mixing ratio in fusion zone, expanded the heat affected zone and increased the nugget size, indentation depth and load bearing capacity. TBF steel was more affected by the thermal cycle during welding than DP600 steel. At high heat input, liquid metal embrittlement based microcrack formations initiating from the surface in the heat affected zone of galvanized TBF steels were observed, while corrosion started rapidly in the welding region of ungalvanized TBF steels. The highest hardness values were observed in ITAB on the TBF steel side. However, a significant softening occurred in the transition zone between the ITAB and base metal on the TBF steel side. The nugget size, indentation depth and load bearing capacity were found to be relatively higher in the galvanized TBF steel group. In dissimilar electrical resistance spot welded TBF/DP600 steel sheets having the same thickness, DP600 steel with lower strength has determined the welding strength. In high heat input during welding process, fractures are of the fusion zone button type with higher welding strength, while fractures are of partial fusion zone button type with lower welding strength in low heat input. If TBF steel is galvanized, relatively higher welding strength was obtained in the welding parameters that provide relatively lower heat input.
- Open Access
- 20 June 2019
- Published by European Mechanical Science in European Mechanical Science
- Vol. 3 (2) , 56-61
Biaxial deformation behavior of friction stir processed TRIP steel sheets
In this study, effects of Friction Stir Processing (FSP) on the biaxial deformation behavior of 1.95 mm thick TRIP 780 steel sheets were investigated. FSP induced large plastic shear strains imposed at elevated temperature of about 945°C have drastically changed both microstructure and flow behavior of the steel. For these reason, after the FSP, significant changes in the microstructural and mechanical properties were obtained. After FSP, initial microstructure of the TRIP-steel transformed into a microstructure that mainly dominated by martensite grains. This transformation resulted with nearly two-fold hardness increase in stir zone. Similarly, lath martensite dominated microstructure elevated the FSPed condition into an ultra-high strength level with expense of room temperature ductility. After FSP, yield strength and UTS increased from 415MPa and 829 MPa to about 1280 MPa and 1475 MPa. Uniform elongation and elongation to failure decreased from 23% and 11% to 34% and 22% respectively. In accordance to decreased ductility, Erichsen index (EI) of the steel decreased from 9.16 mm to 4.90 mm under biaxial stretching conditions In contrast to strength enhancement punch force at EI of TRIP-780 also decreased from 80.6 kN to 45.4 kN respectively. This simultaneous decrease in both Ei and FEi attributed to increase in cracking tendency of the FSP induced microstructure.
- 20 June 2019
- Published by European Mechanical Science in European Mechanical Science
- Vol. 3 (2) , 56-61
Open AccessBiaxial deformation behavior of friction stir processed TRIP steel sheets
In this study, effects of Friction Stir Processing (FSP) on the biaxial deformation behavior of 1.95 mm thick TRIP 780 steel sheets were investigated. FSP induced large plastic shear strains imposed at elevated temperature of about 945°C have drastically changed both microstructure and flow behavior of the steel. For these reason, after the FSP, significant changes in the microstructural and mechanical properties were obtained. After FSP, initial microstructure of the TRIP-steel transformed into a microstructure that mainly dominated by martensite grains. This transformation resulted with nearly two-fold hardness increase in stir zone. Similarly, lath martensite dominated microstructure elevated the FSPed condition into an ultra-high strength level with expense of room temperature ductility. After FSP, yield strength and UTS increased from 415MPa and 829 MPa to about 1280 MPa and 1475 MPa. Uniform elongation and elongation to failure decreased from 23% and 11% to 34% and 22% respectively. In accordance to decreased ductility, Erichsen index (EI) of the steel decreased from 9.16 mm to 4.90 mm under biaxial stretching conditions In contrast to strength enhancement punch force at EI of TRIP-780 also decreased from 80.6 kN to 45.4 kN respectively. This simultaneous decrease in both Ei and FEi attributed to increase in cracking tendency of the FSP induced microstructure.