David Gustafsson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
David Gustafsson has a total of 68 co-authors. Here are the top co-authors by number of shared publications:
Henrik Grosen
Drone Systems Aps
3 shared publications- Peter Bauer-Gottwein
University of Copenhagen, Department of Geosciences and Natural Resource Management, Rolighedsvej 23, 1958 Frederiksberg C, Denmark
3 shared publications Sune Nielsen
Drone Systems Aps
3 shared publications- Zhen Zhou
DTU Sustain, Technical University of Denmark
3 shared publications - Alexander Rietz Vesterhauge
DTU Space Technical University of Denmark Kgs. Lyngby Denmark
2 shared publications Alexey Dobrovolskiy
SPH Engineering Riga Latvia
2 shared publications
Latest Publications
- Open Access
- 15 September 2025
- Published by Wiley
Contactless river discharge from Unoccupied Aerial Systems hydrometry: performance evaluation using a large and diverse set of river cross sections
Unoccupied Aerial Systems offer promising opportunities for monitoring inland water hydrometry. UAS-borne Doppler radar, water-penetrating radar, and radar altimetry enable contactless observation of key hydraulic variables, providing valuable data under hard-to-access or critical conditions. However, a systematic assessment of UAS-based river discharge estimation across diverse river types is still lacking. To address this gap, we present a framework for estimating discharge from UAS-derived water surface velocity, water surface elevation, and river bathymetry with local water surface slope computed from the water level profile. Four surface-to-bulk velocity conversion methods: 0.85 method, log law method, power law method and entropy method were applied. The overall accuracy of UAS discharge estimation algorithm was benchmarked at 46 cross-sections across four river systems with gauge records. We quantified uncertainty propagation from each input variable, assessed their relative contributions, and performed an error propagation experiment with ±30% perturbations to simulate high-bias measurement scenarios. To identify factors controlling performance, we calculated Spearman’s rank correlations between discharge bias, uncertainty metrics, and cross-sectional properties. Results show that, across most sites, at least one method achieved discharge bias within 30%, though no single method consistently outperformed the others. The 0.85 method proved most robust overall, with performance patterns linked to morphology: 0.85 and entropy methods generally better at larger rivers, while high water surface slopes reduced the accuracy of the log law and power law methods. Correlation analysis revealed that surface velocity uncertainty dominated to discharge uncertainty in deep rivers, whereas water surface elevation was more influential in shallow ones.
- 15 September 2025
- Published by Wiley
Open AccessContactless river discharge from Unoccupied Aerial Systems hydrometry: performance evaluation using a large and diverse set of river cross sections
Unoccupied Aerial Systems offer promising opportunities for monitoring inland water hydrometry. UAS-borne Doppler radar, water-penetrating radar, and radar altimetry enable contactless observation of key hydraulic variables, providing valuable data under hard-to-access or critical conditions. However, a systematic assessment of UAS-based river discharge estimation across diverse river types is still lacking. To address this gap, we present a framework for estimating discharge from UAS-derived water surface velocity, water surface elevation, and river bathymetry with local water surface slope computed from the water level profile. Four surface-to-bulk velocity conversion methods: 0.85 method, log law method, power law method and entropy method were applied. The overall accuracy of UAS discharge estimation algorithm was benchmarked at 46 cross-sections across four river systems with gauge records. We quantified uncertainty propagation from each input variable, assessed their relative contributions, and performed an error propagation experiment with ±30% perturbations to simulate high-bias measurement scenarios. To identify factors controlling performance, we calculated Spearman’s rank correlations between discharge bias, uncertainty metrics, and cross-sectional properties. Results show that, across most sites, at least one method achieved discharge bias within 30%, though no single method consistently outperformed the others. The 0.85 method proved most robust overall, with performance patterns linked to morphology: 0.85 and entropy methods generally better at larger rivers, while high water surface slopes reduced the accuracy of the log law and power law methods. Correlation analysis revealed that surface velocity uncertainty dominated to discharge uncertainty in deep rivers, whereas water surface elevation was more influential in shallow ones.
- Open Access
- 15 November 2024
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 60 (11)
Measuring River Surface Velocity Using UAS‐Borne Doppler Radar
Using Unoccupied Aerial Systems (UAS) equipped with optical RGB cameras and Doppler radar, surface velocity can be efficiently measured at high spatial resolution. UAS‐borne Doppler radar is particularly attractive because it is suitable for real‐time velocity determination, because the measurement is contactless, and because it has fewer limitations than image velocimetry techniques. In this paper, five cross‐sections (XSs) were surveyed within a 10 km stretch of Rönne River in Sweden. Ground‐truth surface velocity observations were retrieved with an electromagnetic velocity sensor (OTT MF Pro) along the XS at one m spacing. Videos from a UAS RGB camera were analyzed using both Particle Image Velocimetry (PIV) and Space‐Time Image Velocimetry (STIV) techniques. Furthermore, we recorded full waveform signal data using a Doppler radar at multiple waypoints across the river. An algorithm fits two alternative models to the average amplitude curve to derive the correct river surface velocity based on Gaussian models with: (a) one peak, and (b) two peaks. Results indicate that river flow velocity and propwash velocity caused by the drone can be found in XS where the flow velocity is low, while the drone‐induced propwash velocity can be neglected in fast and highly turbulent flows. To verify the river flow velocity derived from Doppler radar, a mean PIV value within the footprint of the Doppler radar at each waypoint was calculated. Finally, quantitative comparisons of OTT MF Pro data with STIV, mean PIV and Doppler radar revealed that UAS‐borne Doppler radar could reliably measure the river surface velocity.
- 15 November 2024
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 60 (11)
Open AccessMeasuring River Surface Velocity Using UAS‐Borne Doppler Radar
Using Unoccupied Aerial Systems (UAS) equipped with optical RGB cameras and Doppler radar, surface velocity can be efficiently measured at high spatial resolution. UAS‐borne Doppler radar is particularly attractive because it is suitable for real‐time velocity determination, because the measurement is contactless, and because it has fewer limitations than image velocimetry techniques. In this paper, five cross‐sections (XSs) were surveyed within a 10 km stretch of Rönne River in Sweden. Ground‐truth surface velocity observations were retrieved with an electromagnetic velocity sensor (OTT MF Pro) along the XS at one m spacing. Videos from a UAS RGB camera were analyzed using both Particle Image Velocimetry (PIV) and Space‐Time Image Velocimetry (STIV) techniques. Furthermore, we recorded full waveform signal data using a Doppler radar at multiple waypoints across the river. An algorithm fits two alternative models to the average amplitude curve to derive the correct river surface velocity based on Gaussian models with: (a) one peak, and (b) two peaks. Results indicate that river flow velocity and propwash velocity caused by the drone can be found in XS where the flow velocity is low, while the drone‐induced propwash velocity can be neglected in fast and highly turbulent flows. To verify the river flow velocity derived from Doppler radar, a mean PIV value within the footprint of the Doppler radar at each waypoint was calculated. Finally, quantitative comparisons of OTT MF Pro data with STIV, mean PIV and Doppler radar revealed that UAS‐borne Doppler radar could reliably measure the river surface velocity.
- Open Access
- 5 March 2024
- Published by Wiley
Measuring river surface velocity using UAS-borne Doppler radar
Using Unmanned Aerial Systems (UAS) equipped with optical RGB cameras and Doppler radar, surface velocity can be efficiently measured at high spatial resolution. UAS-borne Doppler radar is particularly attractive because it is suitable for real-time velocity determination, because the measurement is contactless, and because it has fewer limitations than image velocimetry techniques. In this paper, five cross-sections (XSs) were surveyed within a 10 km stretch of Rönne Å in Sweden. Ground-truth surface velocity observations were retrieved with an electromagnetic velocity sensor (OTT MF Pro) along the XS at 1 m spacing. Videos from a UAS RGB camera were analyzed using both Particle Image Velocimetry (PIV) and Space-Time Image Velocimetry (STIV) techniques. Furthermore, we recorded full waveform signal data using a Doppler radar at multiple waypoints across the river. An algorithm fits two alternative models to the average amplitude curve to derive the correct river surface velocity: a Gaussian one peak model, or a Gaussian two peak model. Results indicate that river flow velocity and propwash velocity caused by the drone can be found in XS where the flow velocity is low, while the drone-induced propwash velocity can be neglected in fast and highly turbulent flows. To verify the river flow velocity derived from Doppler radar, a mean PIV value within the footprint of the Doppler radar at each waypoint was calculated. Finally, quantitative comparisons of OTT MF Pro data with STIV, mean PIV and Doppler radar revealed that UAS-borne Doppler radar could reliably measure the river surface velocity.
- 5 March 2024
- Published by Wiley
Open AccessMeasuring river surface velocity using UAS-borne Doppler radar
Using Unmanned Aerial Systems (UAS) equipped with optical RGB cameras and Doppler radar, surface velocity can be efficiently measured at high spatial resolution. UAS-borne Doppler radar is particularly attractive because it is suitable for real-time velocity determination, because the measurement is contactless, and because it has fewer limitations than image velocimetry techniques. In this paper, five cross-sections (XSs) were surveyed within a 10 km stretch of Rönne Å in Sweden. Ground-truth surface velocity observations were retrieved with an electromagnetic velocity sensor (OTT MF Pro) along the XS at 1 m spacing. Videos from a UAS RGB camera were analyzed using both Particle Image Velocimetry (PIV) and Space-Time Image Velocimetry (STIV) techniques. Furthermore, we recorded full waveform signal data using a Doppler radar at multiple waypoints across the river. An algorithm fits two alternative models to the average amplitude curve to derive the correct river surface velocity: a Gaussian one peak model, or a Gaussian two peak model. Results indicate that river flow velocity and propwash velocity caused by the drone can be found in XS where the flow velocity is low, while the drone-induced propwash velocity can be neglected in fast and highly turbulent flows. To verify the river flow velocity derived from Doppler radar, a mean PIV value within the footprint of the Doppler radar at each waypoint was calculated. Finally, quantitative comparisons of OTT MF Pro data with STIV, mean PIV and Doppler radar revealed that UAS-borne Doppler radar could reliably measure the river surface velocity.
- Open Access
- 11 May 2023
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 59 (5)
Which Potential Evapotranspiration Formula to Use in Hydrological Modeling World‐Wide?
Although many potential evapotranspiration (PET) formulas are available, there is still a lack of knowledge on when and where to use them in catchment modeling world‐wide. Here we experimented with three different formulas in a global hydrological model (the World‐wide HYPE), using 15 years of observations from 5,338 streamflow gauges and global evapotranspiration from Earth‐observations (MOD16). We tested model performance in a multi‐process approach to select the best formula for catchments covering the global landmass. From comparing the results with land‐cover, climate classification, water‐energy limitations, we found that climate is the main driver behind the spatial patterns in model performance. Hargreaves was the best PET formula in 50% of the catchments, most of them located in the Amazonas, central Europe, and Oceania; Jensen‐Haise was better for catchments in northern latitudes (36%). Finally, Priestley‐Taylor was the best formula for India and latitudes above 65° North. The selection of a PET formula seems to be more critical in tropical regions close to the equator, where the differences in performance are above 50%. This is also where PET is highest. We found a strong connection between the five main Köppen regions and the PET formulas, further supported by landcover analysis. Hence, the PET formulas differed in their capacity to provide useful input to the water balance modeling, with complex formulas only giving improved predictions in temperate and polar regions; however, for the rest of the globe simpler formulas were better. We thus recommend to apply different PET formulas based on climatic regions world‐wide.
- 11 May 2023
- Published by American Geophysical Union (AGU) in Water Resources Research
- Vol. 59 (5)
Open AccessWhich Potential Evapotranspiration Formula to Use in Hydrological Modeling World‐Wide?
Although many potential evapotranspiration (PET) formulas are available, there is still a lack of knowledge on when and where to use them in catchment modeling world‐wide. Here we experimented with three different formulas in a global hydrological model (the World‐wide HYPE), using 15 years of observations from 5,338 streamflow gauges and global evapotranspiration from Earth‐observations (MOD16). We tested model performance in a multi‐process approach to select the best formula for catchments covering the global landmass. From comparing the results with land‐cover, climate classification, water‐energy limitations, we found that climate is the main driver behind the spatial patterns in model performance. Hargreaves was the best PET formula in 50% of the catchments, most of them located in the Amazonas, central Europe, and Oceania; Jensen‐Haise was better for catchments in northern latitudes (36%). Finally, Priestley‐Taylor was the best formula for India and latitudes above 65° North. The selection of a PET formula seems to be more critical in tropical regions close to the equator, where the differences in performance are above 50%. This is also where PET is highest. We found a strong connection between the five main Köppen regions and the PET formulas, further supported by landcover analysis. Hence, the PET formulas differed in their capacity to provide useful input to the water balance modeling, with complex formulas only giving improved predictions in temperate and polar regions; however, for the rest of the globe simpler formulas were better. We thus recommend to apply different PET formulas based on climatic regions world‐wide.
- Open Access
- 22 September 2022
- Published by Copernicus GmbH
Experiences from co-developing hydrological forecasting systems across West Africa and eastern Siberia
Changes in hydrology and society are growing concerns in West Africa and eastern Siberia. Floods cause loss of lives, damaged infrastructure, and reduced food security. A warming climate impacts river ice conditions, affecting ice roads and summertime river transportation. Operational hydrological forecasting systems are needed to boost climate adaptation and resilience in these regions.Within the projects FANFAR (www.fanfar.eu) and HYPE-ERAS (www.hype-eras.org), we work with key stakeholders (e.g. hydrological services and disaster managers) to jointly design, develop, operate and evaluate hydrological forecasting systems in each domain.In West Africa, we used Multi-Criteria Decision Analysis (MCDA) to engage users in the definition and development of the forecasting system. MCDA was employed to clarify and prioritize objectives and system configurations. We found that the most highly prioritized objectives were: high accuracy, clear flood risk information, reliable access, and timely production and distribution of the information. The stakeholders also contributed to forecast evaluation, e.g. by comparing forecasts with field experiences and local observations. Skills vary, with higher probability of detection (POD) in unregulated areas, and lower POD downstream of wetlands and reservoirs. Overall, 75% of the West African agencies considered the forecast accuracy to be “good” or “very good”. This also translated into changed operational warning practices, e.g. in Nigeria where FANFAR information was used to save thousands of lives and property on at least two occasions in 2020.In eastern Siberia, a key target variable to forecast is river ice breakup date. To this end we combined meteorological data (HydroGFD and ECMWF 1-10day forecasts), hydrological modelling (Artic-HYPE), and local observations of river discharge, water level, ice thickness and river ice breakup dates. In both 2020 and 2021, the model successfully predicted the river ice breakup in the Lena River near Yakutsk up to 10 days in advance. We also found a systematic trend of too early breakup in upstream locations, and too late breakup in downstream locations, indicating problems in ice melt and/or growth calibration.Here we summarize the research design, results and experiences gained in FANFAR and HYPE-ERAS; indicating that operational forecasting can be useful to boost climate adaptation and resilience.
- 22 September 2022
- Published by Copernicus GmbH
Open AccessExperiences from co-developing hydrological forecasting systems across West Africa and eastern Siberia
Changes in hydrology and society are growing concerns in West Africa and eastern Siberia. Floods cause loss of lives, damaged infrastructure, and reduced food security. A warming climate impacts river ice conditions, affecting ice roads and summertime river transportation. Operational hydrological forecasting systems are needed to boost climate adaptation and resilience in these regions.Within the projects FANFAR (www.fanfar.eu) and HYPE-ERAS (www.hype-eras.org), we work with key stakeholders (e.g. hydrological services and disaster managers) to jointly design, develop, operate and evaluate hydrological forecasting systems in each domain.In West Africa, we used Multi-Criteria Decision Analysis (MCDA) to engage users in the definition and development of the forecasting system. MCDA was employed to clarify and prioritize objectives and system configurations. We found that the most highly prioritized objectives were: high accuracy, clear flood risk information, reliable access, and timely production and distribution of the information. The stakeholders also contributed to forecast evaluation, e.g. by comparing forecasts with field experiences and local observations. Skills vary, with higher probability of detection (POD) in unregulated areas, and lower POD downstream of wetlands and reservoirs. Overall, 75% of the West African agencies considered the forecast accuracy to be “good” or “very good”. This also translated into changed operational warning practices, e.g. in Nigeria where FANFAR information was used to save thousands of lives and property on at least two occasions in 2020.In eastern Siberia, a key target variable to forecast is river ice breakup date. To this end we combined meteorological data (HydroGFD and ECMWF 1-10day forecasts), hydrological modelling (Artic-HYPE), and local observations of river discharge, water level, ice thickness and river ice breakup dates. In both 2020 and 2021, the model successfully predicted the river ice breakup in the Lena River near Yakutsk up to 10 days in advance. We also found a systematic trend of too early breakup in upstream locations, and too late breakup in downstream locations, indicating problems in ice melt and/or growth calibration.Here we summarize the research design, results and experiences gained in FANFAR and HYPE-ERAS; indicating that operational forecasting can be useful to boost climate adaptation and resilience.
- Open Access
- 21 February 2014
- Published by American Chemical Society (ACS) in ACS Medicinal Chemistry Letters
- Vol. 5 (5) , 538-543
Discovery of the Fibrinolysis Inhibitor AZD6564, Acting via Interference of a Protein–Protein Interaction
A class of novel oral fibrinolysis inhibitors has been discovered, which are lysine mimetics containing an isoxazolone as a carboxylic acid isostere. As evidenced by X-ray crystallography the inhibitors bind to the lysine binding site in plasmin thus preventing plasmin from binding to fibrin, hence blocking the protein–protein interaction. Optimization of the series, focusing on potency in human buffer and plasma clotlysis assays, permeability, and GABAa selectivity, led to the discovery of AZD6564 (19) displaying an in vitro human plasma clot lysis IC50 of 0.44 μM, no detectable activity against GABAa, and with DMPK properties leading to a predicted dose of 340 mg twice a day oral dosing in humans.
- 21 February 2014
- Published by American Chemical Society (ACS) in ACS Medicinal Chemistry Letters
- Vol. 5 (5) , 538-543
Open AccessDiscovery of the Fibrinolysis Inhibitor AZD6564, Acting via Interference of a Protein–Protein Interaction
A class of novel oral fibrinolysis inhibitors has been discovered, which are lysine mimetics containing an isoxazolone as a carboxylic acid isostere. As evidenced by X-ray crystallography the inhibitors bind to the lysine binding site in plasmin thus preventing plasmin from binding to fibrin, hence blocking the protein–protein interaction. Optimization of the series, focusing on potency in human buffer and plasma clotlysis assays, permeability, and GABAa selectivity, led to the discovery of AZD6564 (19) displaying an in vitro human plasma clot lysis IC50 of 0.44 μM, no detectable activity against GABAa, and with DMPK properties leading to a predicted dose of 340 mg twice a day oral dosing in humans.
- Open Access
- 1 January 2003
- Published by American Meteorological Society in Journal of Applied Meteorology and Climatology
- Vol. 42 (1) , 95-112
Boreal Forest Surface Parameterization in the ECMWF Model—1D Test with NOPEX Long-Term Data
The objective of the present study was to assess the performance and recent improvements of the land surface scheme used operationally in the European Centre for Medium-Range Weather Forecasts (ECMWF) in a Scandinavian boreal forest climate/ecosystem. The previous (the 1999 scheme of P. Viterbo and A. K. Betts) and the new (Tiled ECMWF Surface Scheme for Exchange Processes over Land, TESSEL) surface schemes were validated by single-column runs against data from NOPEX (Northern Hemisphere Climate-Processes Land-Surface Experiment). Driving and validation datasets were prepared for a 3-yr period (1994–96). The new surface scheme, with separate surface energy balances for subgrid fractions (tiling), improved predictions of seasonal as well as diurnal variation in surface energy fluxes in comparison with the old scheme. Simulated wintertime evaporation improved significantly as a consequence of the introduced additional aerodynamic resistance for evaporation from snow lying under high vegetation. Simulated springtime evaporation also improved because the limitation of transpiration in frozen soils was now accounted for. However, downward sensible heat flux was still underestimated during winter, especially at nighttime, whereas soil temperatures were underestimated in winter and overestimated in summer. The new scheme also underestimated evaporation during dry periods in summer, whereas soil moisture was overestimated. Sensitivity tests showed that further improvements of simulated surface heat fluxes and soil temperatures could be obtained by calibration of parameters governing the coupling between the surface and the atmosphere and the ground heat flux, and parameters governing the water uptake by the vegetation. Model performance also improved when the seasonal variation in vegetation properties was included.
- 1 January 2003
- Published by American Meteorological Society in Journal of Applied Meteorology and Climatology
- Vol. 42 (1) , 95-112
Open AccessBoreal Forest Surface Parameterization in the ECMWF Model—1D Test with NOPEX Long-Term Data
The objective of the present study was to assess the performance and recent improvements of the land surface scheme used operationally in the European Centre for Medium-Range Weather Forecasts (ECMWF) in a Scandinavian boreal forest climate/ecosystem. The previous (the 1999 scheme of P. Viterbo and A. K. Betts) and the new (Tiled ECMWF Surface Scheme for Exchange Processes over Land, TESSEL) surface schemes were validated by single-column runs against data from NOPEX (Northern Hemisphere Climate-Processes Land-Surface Experiment). Driving and validation datasets were prepared for a 3-yr period (1994–96). The new surface scheme, with separate surface energy balances for subgrid fractions (tiling), improved predictions of seasonal as well as diurnal variation in surface energy fluxes in comparison with the old scheme. Simulated wintertime evaporation improved significantly as a consequence of the introduced additional aerodynamic resistance for evaporation from snow lying under high vegetation. Simulated springtime evaporation also improved because the limitation of transpiration in frozen soils was now accounted for. However, downward sensible heat flux was still underestimated during winter, especially at nighttime, whereas soil temperatures were underestimated in winter and overestimated in summer. The new scheme also underestimated evaporation during dry periods in summer, whereas soil moisture was overestimated. Sensitivity tests showed that further improvements of simulated surface heat fluxes and soil temperatures could be obtained by calibration of parameters governing the coupling between the surface and the atmosphere and the ground heat flux, and parameters governing the water uptake by the vegetation. Model performance also improved when the seasonal variation in vegetation properties was included.