Konstantina Fani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Konstantina Fani has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Eleana Kordouli
Department of Chemistry, University of Patras, GR-26504 Patras, Greece
3 shared publications John Zafeiropoulos
Hellenic Open University Parodos Aristotelous 18
2 shared publicationsKyriakos Bourikas
Hellenic Open University Parodos Aristotelous 18
2 shared publications- Aikaterini Ntempou
Department of Chemistry, University of Patras, GR-26504 Patras, Greece
1 shared publication Alexandros K. Bikogiannakis
1 shared publication- Alexandros Katsaounis
Department of Chemical Engineering, University of Patras, 26504 Patras, Greece
1 shared publication
Latest Publications
- Open Access
- 22 October 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (21) , 10741
Sustainable Green Diesel Production via Hydrotreating of Biodiesel over Fe–Ni Catalysts Supported on Natural Mordenite
Monometallic Ni catalysts supported on zeolites may undergo deactivation through carbon deposition and particle growth during hydrotreating. In this study, FeNi catalysts supported on modified natural mordenite (MO), with total metal loadings of 20–40 wt.%, were prepared by co-deposition–precipitation and evaluated for biodiesel conversion to green diesel. XRD and TEM analyses showed that Fe incorporation was associated with smaller Ni crystallites and a narrower particle size distribution compared with the monometallic 30Ni/MO reference. NH3-TPD measurements indicated changes in ammonia desorption behavior, particularly a reduced high-temperature contribution, while CO chemisorption revealed the highest uptake (137.5 μmol g−1) for 30FeNi/MO. Under the investigated conditions (310 °C, 40 bar H2, 9 h), this catalyst achieved approximately 99% biodiesel conversion and a 97 wt.% diesel-range hydrocarbon fraction. The product carbon-number distribution suggested a greater relative contribution of carbon-removing deoxygenation pathways following Fe incorporation, although definitive mechanistic assignments require additional evidence. Reusability tests revealed substantial deterioration in hydrocarbon production upon direct reuse. Washing and re-activation restored nearly complete biodiesel conversion but only partially recovered hydrocarbon production (66 wt.%). These findings demonstrate promising initial catalytic performance while highlighting limitations in catalyst stability and regeneration.
- 22 October 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (21) , 10741
Open AccessSustainable Green Diesel Production via Hydrotreating of Biodiesel over Fe–Ni Catalysts Supported on Natural Mordenite
Monometallic Ni catalysts supported on zeolites may undergo deactivation through carbon deposition and particle growth during hydrotreating. In this study, FeNi catalysts supported on modified natural mordenite (MO), with total metal loadings of 20–40 wt.%, were prepared by co-deposition–precipitation and evaluated for biodiesel conversion to green diesel. XRD and TEM analyses showed that Fe incorporation was associated with smaller Ni crystallites and a narrower particle size distribution compared with the monometallic 30Ni/MO reference. NH3-TPD measurements indicated changes in ammonia desorption behavior, particularly a reduced high-temperature contribution, while CO chemisorption revealed the highest uptake (137.5 μmol g−1) for 30FeNi/MO. Under the investigated conditions (310 °C, 40 bar H2, 9 h), this catalyst achieved approximately 99% biodiesel conversion and a 97 wt.% diesel-range hydrocarbon fraction. The product carbon-number distribution suggested a greater relative contribution of carbon-removing deoxygenation pathways following Fe incorporation, although definitive mechanistic assignments require additional evidence. Reusability tests revealed substantial deterioration in hydrocarbon production upon direct reuse. Washing and re-activation restored nearly complete biodiesel conversion but only partially recovered hydrocarbon production (66 wt.%). These findings demonstrate promising initial catalytic performance while highlighting limitations in catalyst stability and regeneration.
- 25 August 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (35) , 15886-15898
Transformation of Residual Fatty Biomass into Green Diesel: Optimization of the Reaction Parameters over a MoNi/SiO2 Catalyst
To advance the circular bioeconomy and mitigate fossil fuel dependency, this study evaluates the catalytic valorization of diverse residual fatty biomasses into high-quality renewable (green) diesel. A high-loading bimetallic MoNi/SiO2 catalyst (metal loading: 50 wt %, atomic ratio: Ni/(Ni + Mo) = 0.95) was developed via wet impregnation for hydrodeoxygenation reactions. Under optimized experimental conditions (350 °C, 40 bar), the catalyst achieved a 100 wt % diesel-range hydrocarbon in the liquid product from waste cooking oil (WCO), chicken fat (CHF), and pork fat (POF). Conversely, fatty acid distillates (FAD) and spent coffee ground oil (SCGO) resulted in lower efficiencies (85 and 78 wt %, respectively). The catalyst demonstrated excellent stability during WCO, CHF, and POF hydrodeoxygenation; a minor efficiency decline after the second run was fully restored via thermal regeneration, identifying coking as the primary cause of temporary deactivation. In contrast, FAD and SCGO processing induced a more pronounced efficiency drop after the second cycle, with only partial performance recovery post-regeneration. This behavior confirms that irreversible deactivation is triggered by nitrogenous compounds, supplemented by moisture-induced effects in SCGO. These insights stress the possibility of exploring hazardous fatty wastes by converting them into drop-in biofuels, directly supporting industrial decarbonization efforts.
- 25 August 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (35) , 15886-15898
Transformation of Residual Fatty Biomass into Green Diesel: Optimization of the Reaction Parameters over a MoNi/SiO2 Catalyst
To advance the circular bioeconomy and mitigate fossil fuel dependency, this study evaluates the catalytic valorization of diverse residual fatty biomasses into high-quality renewable (green) diesel. A high-loading bimetallic MoNi/SiO2 catalyst (metal loading: 50 wt %, atomic ratio: Ni/(Ni + Mo) = 0.95) was developed via wet impregnation for hydrodeoxygenation reactions. Under optimized experimental conditions (350 °C, 40 bar), the catalyst achieved a 100 wt % diesel-range hydrocarbon in the liquid product from waste cooking oil (WCO), chicken fat (CHF), and pork fat (POF). Conversely, fatty acid distillates (FAD) and spent coffee ground oil (SCGO) resulted in lower efficiencies (85 and 78 wt %, respectively). The catalyst demonstrated excellent stability during WCO, CHF, and POF hydrodeoxygenation; a minor efficiency decline after the second run was fully restored via thermal regeneration, identifying coking as the primary cause of temporary deactivation. In contrast, FAD and SCGO processing induced a more pronounced efficiency drop after the second cycle, with only partial performance recovery post-regeneration. This behavior confirms that irreversible deactivation is triggered by nitrogenous compounds, supplemented by moisture-induced effects in SCGO. These insights stress the possibility of exploring hazardous fatty wastes by converting them into drop-in biofuels, directly supporting industrial decarbonization efforts.
- Open Access
- 10 May 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (10) , 1603
Influence of Natural Mordenite Activation Mode on Its Efficiency as Support of Nickel Catalysts for Biodiesel Upgrading to Renewable Diesel
In the present work, natural mordenite originated from volcanic soils in Greek islands, activated using HCl solution and HCl solution followed by NaOH solution, was used as support for preparing two metallic nickel catalysts (30 wt.% Ni). The catalysts were thoroughly characterized (XRF, N2 adsorption–desorption, SEM, XRD, TEM, H2-TPR, NH3-TPD) and evaluated for biodiesel upgrading to green (renewable) diesel. Double activation of natural mordenite optimized its supporting characteristics, finally resulting in a supported nickel catalyst with (i) enhanced specific surface area (124 m2 g−1) and enhanced mean pore diameter (14 nm) facilitating mass transfer; (ii) easier nickel phase reduction; (iii) enhanced Ni0 dispersion and thus high active surface; (iv) balanced population of moderate and strong acid sites; (v) resistance to sintering; and (vi) low coke formation. Over the corresponding catalyst, the production of a liquid consisting of 94 wt.% renewable diesel was achieved, after 9 h of reaction at 350 °C and 40 bar H2 pressure, in a semi-batch reactor under solvent-free conditions.
- 10 May 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (10) , 1603
Open AccessInfluence of Natural Mordenite Activation Mode on Its Efficiency as Support of Nickel Catalysts for Biodiesel Upgrading to Renewable Diesel
In the present work, natural mordenite originated from volcanic soils in Greek islands, activated using HCl solution and HCl solution followed by NaOH solution, was used as support for preparing two metallic nickel catalysts (30 wt.% Ni). The catalysts were thoroughly characterized (XRF, N2 adsorption–desorption, SEM, XRD, TEM, H2-TPR, NH3-TPD) and evaluated for biodiesel upgrading to green (renewable) diesel. Double activation of natural mordenite optimized its supporting characteristics, finally resulting in a supported nickel catalyst with (i) enhanced specific surface area (124 m2 g−1) and enhanced mean pore diameter (14 nm) facilitating mass transfer; (ii) easier nickel phase reduction; (iii) enhanced Ni0 dispersion and thus high active surface; (iv) balanced population of moderate and strong acid sites; (v) resistance to sintering; and (vi) low coke formation. Over the corresponding catalyst, the production of a liquid consisting of 94 wt.% renewable diesel was achieved, after 9 h of reaction at 350 °C and 40 bar H2 pressure, in a semi-batch reactor under solvent-free conditions.