Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Olcay Gençyılmaz has a total of 36 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Fabrication, Electrical Performance and Comparison of Ag/p-NiO/ n-ITO/Ag, Ag/p-NiO/n-FTO/Ag, Ag/p-NiO/Glass/Ag Heterostructure Thin Films

    by Olcay Gençyilmaz, İlKer Kara, Ahmed Majeed Fadhil Alsamarai

    In this study, we fabricated and analysed heterostructure thin films based on nickel oxide (NiO) films using the low-cost successive ionic layer adsorption and reaction (SILAR) method. NiO films were deposited on three substrates: indium tin oxide (ITO), fluorine tin oxide (FTO) and glass. The structural, optical, electrical and surface properties of the NiO films were investigated, revealing that all films have a cubic crystal structure with grain sizes varying between 30-60 nm. The optical energy range of the films was determined to be between 3.56-4 eV by analysing their optical properties. Furthermore, it was observed that the use of ITO base in Ag/p-NiO/n-ITO/Ag heterostructure thin films significantly increased their transmittance values to approximately 40%. The I-V characteristics of Ag/p-NiO/n-ITO/Ag, Ag/p-NiO/n-FTO/Ag and Ag/p-NiO/Glass/Ag heterostructures were examined. The maximum barrier height (ΦB) for the Ag/p-NiO/n-ITO/Ag heterostructure thin film was found to be 0.55 eV. In addition, the minimum ideality factor for this film was obtained to be 1.44 eV. The I-V analysis revealed that the Ag/p-NiO/n-ITO/Ag heterostructure is particularly suitable as a photoanode for solar cell applications.


  • Open Access

    Comparison of high antioxidant ZnONPs produced from different fungi as alternative biomaterials

    by Olcay Gençyılmaz, Mohanad Fawzi Mutar Mutar

    In this study, zinc oxide nanoparticles (ZnONPs), a promising alternative biomaterial, were synthesized using a non-toxic, cost-effective green synthesis approach using various fungal species (Penicillium citrinum, Fusarium solani, Aspergillus flavus and Aspergillus niger). The effect of different fungal species on the structural, optical, morphological and antimicrobial properties of ZnO nanoparticles (ZnONPs) was compared. ZnO nanoparticles (ZnONPs) crystallized in a hexagonal wurtzite structure with grain sizes ranging from 45 to 61 nm. Fungal species had a significant effect on the surface plasmon resonance (SPR) peak observed at 302 nm. ZnONPs were obtained in different morphologies such as nanodiscs, nanospheres, nanorchins and nanonuts, and it was determined that fungal species had a significant effect on these structures. The antibacterial activity of ZnONPs against Candida albicans, Streptococcus mutans, Pseudomonas aeruginosa, Eosinophilic pneumonia and Staphylococcus aureus was investigated. The effect of these nanoparticle shapes on antibacterial activity was evaluated. ZnONPs were found to have a significant antimicrobial effect especially on Candida albicans and Streptococcus mutans. ZnONPs produced only with Aspergillus niger fungus were found to have a strong antimicrobial effect especially on Staphylococcus aureus. Based on these results, the biosynthesis of ZnO nanoparticles (ZnONPs) using Penicillium citrinum, Fusarium solani, Aspergillus flavus and Aspergillus niger fungal species is proposed for the production of ZnONPs as a biomaterial with remarkable antibacterial properties and various morphologies.


  • Open Access

    ZnO/ITO, Sn and Cu Doped ZnO/ITO Films as an Photoanode for Solar Cell: Production and Characterizations

    by İlKer Kara, Dheyaaldain Mohammed Hussein Alhasani, Ahmet Furkan Kayis, Özcan Yalçınkaya, Olcay Gençyılmaz, Abjar Ibrahim Rashid Hafedh

    Undoped ZnO and Sn- and Cu-doped ZnO thin films were fabricated on ITO substrates via the SILAR method for this study. The films were then subjected to structural, surface, optical, and electrical characterization. The undoped ZnO thin films displayed a spherical surface morphology, while the Sn-doped ZnO thin films exhibited a nano-flower surface morphology. On the other hand, the Cu-doped ZnO thin films demonstrated a relatively thicker and flat layer, as well as a fractured surface morphology that resulted in voids. The level of crystallization and transmittance values augmented upon doping. With Cu doping, n-p heterojunction structure was obtained from ZnO/ITO films. Hence, it is inferred that the generated Cu doped ZnO/ITO films can serve as alternative transparent conductive films (TCO) due to their low resistivity.


  • Open Access

    Analyzing antimicrobial activity of ZnO/FTO, Sn–Cu‐doped ZnO/FTO thin films: Production and characterizations

    by Ilker Kara, Abjar Ibrahim Rashid Hafedh, Nooralhuda Kareem Hanoon Alhusseinawi, Ahmet Furkan Kayış, Özcan Yalçınkaya, Berat Cinar Acar, Zehranur Yuksekdag, Yunus Ozen, Olcay Gençyılmaz, Engin Can Ozkan, et al.

    In the developing field of nanotechnology, ZnO (zinc oxide) based semiconductor samples have emerged as the foremost choice due to their immense potential for advancing the development of cutting‐edge nanodevices. Due to its excellent chemical stability, low cost, and non‐toxicity to biological systems, it is also utilized in various investigations. In this study, the successive ionic layer adsorption and reaction (SILAR) method was used to generate FTO (fluorine‐doped tin oxide)/ZnO, and tin (Sn)–copper (Cu)‐doped ZnO thin films at varying concentrations on FTO substrates. After being stacked 40 times in varying concentrations on the FTO substrate, FTO/ZnO thin films and Sn–Cu‐doped thin films were annealed at 300°C. Using Scanning Electron Microscopy (SEM) Energy Dispersive Spectroscopy‐(EDS), the agar diffusion test, and the viability cell counting method, the minimum inhibitory concentration, structural properties, surface morphology, antibacterial properties, bacterial adhesion, and survival organism count of FTO/ZnO thin films and Sn–Cu‐doped thin films were investigated. Both doped and FTO/ZnO films with varying Sn–Cu concentrations expanded harmonically on the FTO substrate, according to the SEM‐EDS investigation. The doping concentration affected their morphological properties, causing changes depending on the doping level. Antibacterial activity was observed in the powder metals, but no antibacterial activity was found in the thin film form. The highest adhesion rate of bacterial organisms on the produced samples was observed when the FTO/ZnO/Sn–Cu doping rate was 1%. In addition, the lowest adhesion rate was observed when the FTO/ZnO/Sn–Cu additive ratio was 3%.Research Highlights: ZnO based semiconductors highlight significant potential in advancing nanodevice technology due to their chemical stability, cost‐effectiveness, and biocompatibility. Employing the SILAR method, the study innovatively fabricates FTO/ZnO and Sn–Cu‐doped ZnO thin films on FTO substrates, exploring a novel approach in semiconductor manufacturing. Post annealing at 300°C, the research examines the structural and surface morphological changes in the films, contributing to the understanding of semiconductor behavior under varying conditions. The study delves into the antibacterial properties of ZnO thin films, offering insights into the potential biomedical applications of these materials. SEM‐EDS analysis reveals that doping concentrations crucially influence the morphological properties of ZnO thin films, shedding light on the optimization of semiconductor performance. Findings indicate a specific doping rate (1% Sn–Cu) enhances bacterial adhesion, while a 3% additive ratio minimizes it, suggesting implications for biomedical device engineering and antibacterial surface design.


  • Open Access

    Binary ZnS–ZnO films as an alternative buffer layer for solar cell applications

    by Olcay Gençyılmaz, İdRis Akyüz, Ferhunde Atay

    In this research, binary ZnS–ZnO films were fabricated by a two-step process, offering an alternative buffer layer solution for photovoltaic solar cell applications. ZnS films were attained through thermal evaporation, after which they were annealed in air at separate temperatures resulting in films containing both ZnS and ZnO phases. Structural, electrical, ellipsometric, optical, and surface properties were examined in detail to elucidate their applicability as a buffer layer in photovoltaic applications. X-ray diffraction patterns revealed that the films exhibit cubic ZnS and hexagonal ZnO crystal structures, wherein crystallite size is augmented with higher annealing temperatures. ZnS films exhibited a needle-shaped surface morphology, as confirmed through atomic force microscopy (AFM) and field emission scanning electron microscopy (FESEM) images. Annealing caused noteworthy modifications on the surfaces of the films. Additionally, absorption spectra denote two distinct absorption regions forming as a result of the annealing process, possibly indicating the emergence of ZnS and ZnO phases. Photoluminescence analyses demonstrate that binary ZnS–ZnO films exhibit greater emission intensities than single-phase ZnS films. Additionally, the annealing process caused the electrical resistivity of films to reduce from 1.28 × 105 to 3.84 × 101 Ω cm. These results suggest that binary ZnS–ZnO films produced via annealing can be considered as promising buffer layers in potential photovoltaic solar cell applications.


  • Open Access

    Effect of Plasma Liquid on Colloidal (CoNPs) and (PtNPs) Nanostructures Produced by Laser Ablation Technique for Antibacterial Applications

    by Entidhar Jasim Khamees, Halah Mohammed Azeez, Ahmed Shaker Hussein, Rafea T. Ahmed, Olcay Gençyılmaz

    In this work, the biological and physical properties of colloidal platinum (PtNPs) and cobalt (CoNPs) nanoparticles were examined for antibacterial applications. The colladial PtNPs and CoNPs nanoparticles were produced using two different liquids (double-distilled water (DDDW) and Dulbecco’s Modified Eagle’s Medium (DMEM)) by laser ablation technique (PLAL). Characterization techniques such as transmission electron microscopy (TEM), UV-vis spectroscopy and Fourier transform infrared (FTIR) were used to determine some physical properties of PtNPs and CoNPs. The antibacterial effects ofcolladial PtNPs and CoNPs at different doses on various bacteria were investigated and their antibacterial activity resistances were calculated by measuring the inhibition zone widths. The effect of the liquid used in the production, the type of bacteria and dose amounts on the antibacterial resistance of these nanoparticles were determined. In this study, it has been shown that the liquid used in the production of PtNPs and CoNPs can create significant changes in the physical and antibacterial properties of nanoparticles, especially by changing the size and concentration of collodial PtNPs.


  • Open Access

    Nanoflower-Like Cu Doped ZnO Films Prepared by SILAR Method: Synthesis, Structural, Optical and Surface Properties

    by İlker Kara, Olcay Gençyılmaz

    ZnO thin films with nanoflower structures have recently got more attention owing to its applications in many fields such as electronics, magnetic and optics. In this study, we synthesized ZnO films as nanoflower surface properties by doping Cu at different rates (1,2 and 3 %) using sequential ionic layer adsorption and reaction (SILAR) method. The effect of Cu doping on the structural, optical and surface properties of ZnO films was investigated using some characterization techniques such as FESEM (Field Emission Scanning Electron Microscopy), EDS (Energy Dispersive Spectroscopy), Raman spectroscopy and UV-vis spectrometer. Cu doping increased the permeability of ZnO films and caused the formation of double band gap structures in the band structure. The ZnO band gap value (~3.59 eV) was increased with Cu doping. In photoluminescence measurements (PL), ZnO and Cu doped films clearly showed near band emission (~397 nm) and deep level emissions, and the defects that created these emissions were identified. The synthesized ZnO films were characterized morphologically by FESEM-Mapping techniques and results showed the nanoflower structures. In addition, ZnO films had higher stoichiometry with Cu addition in EDS results. Especially the surface and optical properties of ZnO films have been made more suitable with Cu (3%) doping for use in various application areas.

  • Yenilenebilir Enerji Kaynaklarından Biyogazın Enerjisinin Çankırı İl’i İçin Potansiyelinin Belirlenmesi ve Kullanılabilirliği

    by Olcay Gençyilmaz, Gamze Seçki̇n

    Son yıllarda, tüm dünya artan enerji ihtiyacının karşılanması ve çevresel sorunların çözümü için yenilenebilir kaynakların kullanımı üzerine yoğunlaşılmıştır. Türkiye’de yenilenebilir enerji kaynaklarının kullanımını arttırmak ve enerji bağımlılığını azaltmak için çeşitli çalışmalar yapılmaktadır. Bu yüzden, Türkiye’deki alternatif kaynak arayışı biyogaz enerjisi üretiminin yaygınlaşmasına sebep olmuştur. Özellikle bölgesel olarak tarım ve hayvancılığa uygun olan bölgelerde biyogaz üretimini arttırmak için çalışmalar yapılmaktadır. Bu bölgelerde bitkisel ve hayvansal atıkların biyogaz üretiminde kullanılması alternatif enerji üretimine ve atık yönetimine olumlu katkı sağlamaktadır. Bu çalışmada, biyogaz enerji potansiyeli ve kullanılabilirliği Türkiye’nin İç Anadolu Bölgesi’ndeki Çankırı İl’i için araştırılmıştır. Yoğun olarak tarım ve hayvancılık sektörünün geliştiği, sanayileşme oranının düşük olduğu bu ilde elde edilen hayvansal atıklardan üretilebilecek biyogaz enerji potansiyeli belirlenmiştir. Biyokimyasal metan üretim potansiyeli (BMP) ve elektrik üretimine katkısı hesaplanarak her bir ilçe için ayrı ayrı bölgesel harita ve grafikleri çizilerek biyogaz enerji potansiyeli analizi yapılmıştır. Ayrıca, biyogaz üretiminden elde edilecek elektrik geliri ve CO2 emisyon değerleri belirlenmiştir.