Arif Balci
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Arif Balci has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Fatih Alibeyoğlu
Department of Mechanical Engineering, Faculty of Engineering and Architecture, Kafkas University, Kars, Turkey
3 shared publications - Mehmet Fatih Aycan
Department of Mechanical Engineering Institute for Graduate School of Natural and Applied Sciences Gazi University Ankara Türkiye
2 shared publications - Mustafa Yurdakul
Gazi Üniversitesi
2 shared publications - Teyfik Demir
Department of Mechanical Engineering, TOBB University of Economics and Technology, Ankara, Turkey
2 shared publications - Yusuf Usta
Gazi Üniversitesi
2 shared publications - Furkan Küçükaltun
Mechanical Engineering Department, Gazi University, Ankara, Turkey
1 shared publication
Latest Publications
- Open Access
Multi-Modal Physics-Informed Neural Network for Single-Track Geometry Prediction in Powder-Bed Arc Additive Manufacturing of 316L Stainless Steel
This study presents a methodology for predicting the geometric features of single tracks of 316L stainless steel produced by Powder-Bed Arc Additive Manufacturing (PBAAM) from four independent process parameters using a multi-modal Physics-Informed Neural Network (PINN). PBAAM shares the same powder-deposition and layering scheme as Laser Powder Bed Fusion (LPBF) but uses a low-current micro-TIG arc rather than a laser as the heat source. A multi-task PINN architecture was developed that simultaneously predicts five geometric features measured from two imaging modalities (top-view and side-view arc), namely the arc core diameter (Dq), the arc cone angle (αc), the heat-affected zone width (wHAZ), the track core width (dcore) and the areal equivalent track width (wiz), from four input parameters (arc current, traverse speed, work angle and working distance). The model was assessed on a full-factorial training matrix of 36 experiments and on four pure speed extrapolation experiments above the training range. A composite quality score filter classified 23 of the training experiments as stable and 13 as unstable. On the pure validation set, the mean absolute percentage error (MAPE) was 4.25% (95% confidence interval 0.91–8.49) for the arc core diameter, 6.29% (5.07–7.59) for the arc cone angle, 8.06% (6.08–9.82) for the heat-affected zone width, and 17.02% (10.77–21.62) for the track core width. Classical regression baselines attain comparable aggregate errors on this narrowly distributed validation set; the distinguishing property of the proposed model is the joint, physically ordered prediction of all five outputs. The Ayrton voltage sub-module of the model converged to U(I) = 11.33 + 97.13/I without any direct voltage measurement, purely through the physics loss term; this function is consistent with the order of magnitude expected from the physics of low-current TIG arcs. The results indicate that physics-informed learning can be applied to the PBAAM process parameter space under small-sample conditions. This capability is demonstrated for 316L stainless steel, for the micro-TIG electrode configuration and the process window investigated here, for single tracks rather than multi-layer builds, and against a validation set of four experiments varying in a single direction.
Open AccessMulti-Modal Physics-Informed Neural Network for Single-Track Geometry Prediction in Powder-Bed Arc Additive Manufacturing of 316L Stainless Steel
This study presents a methodology for predicting the geometric features of single tracks of 316L stainless steel produced by Powder-Bed Arc Additive Manufacturing (PBAAM) from four independent process parameters using a multi-modal Physics-Informed Neural Network (PINN). PBAAM shares the same powder-deposition and layering scheme as Laser Powder Bed Fusion (LPBF) but uses a low-current micro-TIG arc rather than a laser as the heat source. A multi-task PINN architecture was developed that simultaneously predicts five geometric features measured from two imaging modalities (top-view and side-view arc), namely the arc core diameter (Dq), the arc cone angle (αc), the heat-affected zone width (wHAZ), the track core width (dcore) and the areal equivalent track width (wiz), from four input parameters (arc current, traverse speed, work angle and working distance). The model was assessed on a full-factorial training matrix of 36 experiments and on four pure speed extrapolation experiments above the training range. A composite quality score filter classified 23 of the training experiments as stable and 13 as unstable. On the pure validation set, the mean absolute percentage error (MAPE) was 4.25% (95% confidence interval 0.91–8.49) for the arc core diameter, 6.29% (5.07–7.59) for the arc cone angle, 8.06% (6.08–9.82) for the heat-affected zone width, and 17.02% (10.77–21.62) for the track core width. Classical regression baselines attain comparable aggregate errors on this narrowly distributed validation set; the distinguishing property of the proposed model is the joint, physically ordered prediction of all five outputs. The Ayrton voltage sub-module of the model converged to U(I) = 11.33 + 97.13/I without any direct voltage measurement, purely through the physics loss term; this function is consistent with the order of magnitude expected from the physics of low-current TIG arcs. The results indicate that physics-informed learning can be applied to the PBAAM process parameter space under small-sample conditions. This capability is demonstrated for 316L stainless steel, for the micro-TIG electrode configuration and the process window investigated here, for single tracks rather than multi-layer builds, and against a validation set of four experiments varying in a single direction.
- 20 July 2026
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 40 (17) , 2913-2949
From infill to interface: Taguchi optimization and cohesive zone modelling of adhesively bonded FDM PLA lap joints
1. Additive manufacturing (AM) technologies have found increasingly widespread application in the aerospace, biomedical, automotive and consumer goods sectors over the past decade, owing to the adv...
- 20 July 2026
- Published by Taylor & Francis in Journal of Adhesion Science and Technology
- Vol. 40 (17) , 2913-2949
From infill to interface: Taguchi optimization and cohesive zone modelling of adhesively bonded FDM PLA lap joints
1. Additive manufacturing (AM) technologies have found increasingly widespread application in the aerospace, biomedical, automotive and consumer goods sectors over the past decade, owing to the adv...
- 15 July 2026
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 9 (4) , 1884-1894
The Effect of Electrode Diameter on Single-Track Morphology and Process Window in Powder-Bed Arc Additive Manufacturing
Powder-bed arc additive manufacturing (PBAAM) is a low-cost alternative powder bed fusion process that uses a TIG arc as heat source. This study systematically investigates the effect of electrode diameter (φ = 0.6, 0.8 and 1.0 mm) on single-track morphology and process window in inclined-bed PBAAM of 316L stainless steel powder. Twenty-seven full-factorial combinations of three current levels (I = 20, 25, 30 A) and three travel speeds (v = 2, 3, 4 mm/s) were evaluated using an image analysis framework based on Otsu thresholding with expert manual correction. Maximum gap length (L_gap) and width coefficient of variation (CV = σ_w/w̄) metrics were compared across six threshold scenarios (S1–S6); S5 (L_gap) = 0.50 mm, CV = 0.15) was identified as the most appropriate combination based on physical justification and literature consistency. Process map analysis revealed travel speed v as the most critical parameter governing the process window: at v = 2 mm/s, 9/9 combinations (100%) produced continuous tracks; at v = 4 mm/s, only 5/9 (56%) were continuous. Multiple linear regression models achieved R² = 0.626 for mean track width w̄ and R² = 0.562 for CV. Electrode diameter φ significantly affects track width (β_φ = 0.762, p = 0.019) but has no significant linear effect on width uniformity CV (p = 0.955); CV is primarily governed by I and v. The φ = 0.8 mm electrode confined all Fragmented/Balling combinations to v = 4 mm/s only and produced approximately 35% lower mean CV (0.184) than the other two electrode diameters for continuous tracks.
- 15 July 2026
- Published by Black Sea Journal of Engineering and Science in Black Sea Journal of Engineering and Science
- Vol. 9 (4) , 1884-1894
The Effect of Electrode Diameter on Single-Track Morphology and Process Window in Powder-Bed Arc Additive Manufacturing
Powder-bed arc additive manufacturing (PBAAM) is a low-cost alternative powder bed fusion process that uses a TIG arc as heat source. This study systematically investigates the effect of electrode diameter (φ = 0.6, 0.8 and 1.0 mm) on single-track morphology and process window in inclined-bed PBAAM of 316L stainless steel powder. Twenty-seven full-factorial combinations of three current levels (I = 20, 25, 30 A) and three travel speeds (v = 2, 3, 4 mm/s) were evaluated using an image analysis framework based on Otsu thresholding with expert manual correction. Maximum gap length (L_gap) and width coefficient of variation (CV = σ_w/w̄) metrics were compared across six threshold scenarios (S1–S6); S5 (L_gap) = 0.50 mm, CV = 0.15) was identified as the most appropriate combination based on physical justification and literature consistency. Process map analysis revealed travel speed v as the most critical parameter governing the process window: at v = 2 mm/s, 9/9 combinations (100%) produced continuous tracks; at v = 4 mm/s, only 5/9 (56%) were continuous. Multiple linear regression models achieved R² = 0.626 for mean track width w̄ and R² = 0.562 for CV. Electrode diameter φ significantly affects track width (β_φ = 0.762, p = 0.019) but has no significant linear effect on width uniformity CV (p = 0.955); CV is primarily governed by I and v. The φ = 0.8 mm electrode confined all Fragmented/Balling combinations to v = 4 mm/s only and produced approximately 35% lower mean CV (0.184) than the other two electrode diameters for continuous tracks.
- Open Access
- 13 April 2026
- Published by MDPI AG in Mathematics
- Vol. 14 (8) , 1296
Interpretable Machine Learning for Process Parameter Analysis in Arc-Driven Powder Bed Fusion of 316L Stainless Steel
Arc-driven powder bed fusion represents a low-cost alternative to beam-based powder bed systems, yet the morphological stability regimes governing single-track formation and the relative influence of process parameters on regime transitions have not been systematically characterised. Manual visual assessment of track morphology is inherently subjective and cannot objectively quantify the parameter hierarchy governing stability boundaries. This study addresses both limitations through two complementary contributions. A deterministic two-stage image-based framework is developed to automatically classify single-track morphology from top-view images of solidified 316L stainless steel tracks, replacing subjective assessment with a reproducible, intervention-free procedure. A gap-based continuity criterion distinguishes discontinuous from continuous melt paths; for continuous tracks, the coefficient of variation in width (CV (coefficient of variation) < 0.15) further separates geometrically stable from transitional morphologies. Building on the image-derived regime labels, two interpretable classifiers—a depth-limited Decision Tree (DT) and a regularised Logistic Regression (LR)—are fitted using applied current, scanning speed, and electrode-to-powder-bed distance as predictors. The classifiers are employed not for predictive generalisation but to extract standardised coefficients and permutation-based feature importance rankings, yielding a model-agnostic, quantitative explanation of which process parameters govern regime transitions. Stable continuous tracks are obtained only within a restricted parameter window. Permutation importance consistently ranks applied current as the dominant predictor, followed by electrode distance and scanning speed, in agreement with the thermophysical interpretation. Logistic Regression coefficients confirm that reduced stand-off distance is a necessary condition for sufficient arc constriction. Supplementary linear regression models indicate that applied current governs melt pool depth, whereas scanning speed is the primary determinant of width variation. The combined framework establishes a reproducible basis for process parameter hierarchy analysis in arc-driven powder bed systems and provides a foundation for regression-based process optimisation.
- 13 April 2026
- Published by MDPI AG in Mathematics
- Vol. 14 (8) , 1296
Open AccessInterpretable Machine Learning for Process Parameter Analysis in Arc-Driven Powder Bed Fusion of 316L Stainless Steel
Arc-driven powder bed fusion represents a low-cost alternative to beam-based powder bed systems, yet the morphological stability regimes governing single-track formation and the relative influence of process parameters on regime transitions have not been systematically characterised. Manual visual assessment of track morphology is inherently subjective and cannot objectively quantify the parameter hierarchy governing stability boundaries. This study addresses both limitations through two complementary contributions. A deterministic two-stage image-based framework is developed to automatically classify single-track morphology from top-view images of solidified 316L stainless steel tracks, replacing subjective assessment with a reproducible, intervention-free procedure. A gap-based continuity criterion distinguishes discontinuous from continuous melt paths; for continuous tracks, the coefficient of variation in width (CV (coefficient of variation) < 0.15) further separates geometrically stable from transitional morphologies. Building on the image-derived regime labels, two interpretable classifiers—a depth-limited Decision Tree (DT) and a regularised Logistic Regression (LR)—are fitted using applied current, scanning speed, and electrode-to-powder-bed distance as predictors. The classifiers are employed not for predictive generalisation but to extract standardised coefficients and permutation-based feature importance rankings, yielding a model-agnostic, quantitative explanation of which process parameters govern regime transitions. Stable continuous tracks are obtained only within a restricted parameter window. Permutation importance consistently ranks applied current as the dominant predictor, followed by electrode distance and scanning speed, in agreement with the thermophysical interpretation. Logistic Regression coefficients confirm that reduced stand-off distance is a necessary condition for sufficient arc constriction. Supplementary linear regression models indicate that applied current governs melt pool depth, whereas scanning speed is the primary determinant of width variation. The combined framework establishes a reproducible basis for process parameter hierarchy analysis in arc-driven powder bed systems and provides a foundation for regression-based process optimisation.
- Open Access
Effect of Layer Thickness and Scanning Parameters on Melt Pool Geometry and Track Continuity in Powder-Bed Arc Additive Manufacturing
Powder-bed arc additive manufacturing (PBAAM) may reduce the cost of powder-bed metal additive manufacturing and enable thicker layers than laser powder bed fusion (LPBF), but melt-track stability limits are not well established. Here, 316L stainless steel powder (15–53 µm) was melted by a TIG-based arc in a custom powder-bed system while varying current, travel speed, layer thickness and hatch distance. Single tracks on an inclined bed (≈0–0.4 mm thickness) were used to identify continuity loss and melt-pool width, quantified from top-view images via width profiles, a gap-based continuity metric and the coefficient of variation. Parallel-track tests at 0.15, 0.20 and 0.25 mm layer thickness with hatch distances set to 25%, 50% and 75% of the measured melt-pool width assessed inter-track bonding and lack of fusion, and selected parameters were validated in five-layer builds. Higher current with low-to-moderate travel speeds produced wider, more stable melt pools on the inclined bed. Hatch ratios of 25–50% were the most effective for sustaining fusion in single layers and multi-layer builds, whereas 75% promoted unbonded regions and narrow-track morphologies. Overall, PBAAM can process substantially thicker layers with relatively simple equipment, but requires a narrow, carefully tuned window to balance continuity, fusion and heat accumulation.
Open AccessEffect of Layer Thickness and Scanning Parameters on Melt Pool Geometry and Track Continuity in Powder-Bed Arc Additive Manufacturing
Powder-bed arc additive manufacturing (PBAAM) may reduce the cost of powder-bed metal additive manufacturing and enable thicker layers than laser powder bed fusion (LPBF), but melt-track stability limits are not well established. Here, 316L stainless steel powder (15–53 µm) was melted by a TIG-based arc in a custom powder-bed system while varying current, travel speed, layer thickness and hatch distance. Single tracks on an inclined bed (≈0–0.4 mm thickness) were used to identify continuity loss and melt-pool width, quantified from top-view images via width profiles, a gap-based continuity metric and the coefficient of variation. Parallel-track tests at 0.15, 0.20 and 0.25 mm layer thickness with hatch distances set to 25%, 50% and 75% of the measured melt-pool width assessed inter-track bonding and lack of fusion, and selected parameters were validated in five-layer builds. Higher current with low-to-moderate travel speeds produced wider, more stable melt pools on the inclined bed. Hatch ratios of 25–50% were the most effective for sustaining fusion in single layers and multi-layer builds, whereas 75% promoted unbonded regions and narrow-track morphologies. Overall, PBAAM can process substantially thicker layers with relatively simple equipment, but requires a narrow, carefully tuned window to balance continuity, fusion and heat accumulation.
- Open Access
- 30 August 2025
- Published by International Journal of 3D Printing Technologies and Digital Industry in International Journal of 3D Printing Technologies and Digital Industry
- Vol. 9 (2) , 183-193
316L PASLANMAZ ÇELİK TOZUNUN ARK İLE TEK ÇİZGİ ERGİTİLMESİNDE ELEKTROT MESAFESİNİN ETKİLERİNİN ARAŞTIRILMASI
Eklemeli imalat yöntemleri, karmaşık geometrilerin ve prototip numunelerin üretimindeki avantajları nedeniyle yaygın olarak araştırılmaktadır. Toz yatakta birleştirmede, uygun ısı kaynağı ve işlem parametrelerinin belirlenmesi tek çizgi katılaşma ile başlamaktadır. Bu çalışmada, lazer ve elektron ışınına alternatif olarak ark kullanılarak, 316L paslanmaz çelik tozunun tek çizgi ergitilebilirliği incelenmiştir. Ergitmeler 0,4 mm kalınlığındaki toz yatakta, 17, 22 ve 27 amper akım değerleri ile gerçekleştirilmiş; ilerleme hızları 1 ve 2 mm/s, elektrot mesafeleri ise 0,7 ve 1 mm olarak belirlenmiştir. Farklı parametre kombinasyonları ile yapılan deneylerde katılaşma geometrisi, ısıl etkilenmiş bölge ve mikroyapı detaylı olarak değerlendirilmiştir. Elde edilen sonuçlar, düşük akım ve yüksek ilerleme hızlarında çizgisel katılaşma kabiliyetinin azaldığını; yüksek akım ve düşük ilerleme hızlarında ise daha geniş ve homojen katılaşma bölgelerinin oluştuğunu göstermektedir. Elektrot mesafesindeki artışın enerji yoğunluğunu azaltarak katılaşma genişliği ve tabla nüfuziyetini düşürdüğü belirlenmiştir. Çalışma, ark kullanımının lazer ve elektron ışınına alternatif olarak uygulanabilirliğini ortaya koymakta ve işlem parametrelerinin optimizasyonu için önemli bulgular sunmaktadır.
- 30 August 2025
- Published by International Journal of 3D Printing Technologies and Digital Industry in International Journal of 3D Printing Technologies and Digital Industry
- Vol. 9 (2) , 183-193
Open Access316L PASLANMAZ ÇELİK TOZUNUN ARK İLE TEK ÇİZGİ ERGİTİLMESİNDE ELEKTROT MESAFESİNİN ETKİLERİNİN ARAŞTIRILMASI
Eklemeli imalat yöntemleri, karmaşık geometrilerin ve prototip numunelerin üretimindeki avantajları nedeniyle yaygın olarak araştırılmaktadır. Toz yatakta birleştirmede, uygun ısı kaynağı ve işlem parametrelerinin belirlenmesi tek çizgi katılaşma ile başlamaktadır. Bu çalışmada, lazer ve elektron ışınına alternatif olarak ark kullanılarak, 316L paslanmaz çelik tozunun tek çizgi ergitilebilirliği incelenmiştir. Ergitmeler 0,4 mm kalınlığındaki toz yatakta, 17, 22 ve 27 amper akım değerleri ile gerçekleştirilmiş; ilerleme hızları 1 ve 2 mm/s, elektrot mesafeleri ise 0,7 ve 1 mm olarak belirlenmiştir. Farklı parametre kombinasyonları ile yapılan deneylerde katılaşma geometrisi, ısıl etkilenmiş bölge ve mikroyapı detaylı olarak değerlendirilmiştir. Elde edilen sonuçlar, düşük akım ve yüksek ilerleme hızlarında çizgisel katılaşma kabiliyetinin azaldığını; yüksek akım ve düşük ilerleme hızlarında ise daha geniş ve homojen katılaşma bölgelerinin oluştuğunu göstermektedir. Elektrot mesafesindeki artışın enerji yoğunluğunu azaltarak katılaşma genişliği ve tabla nüfuziyetini düşürdüğü belirlenmiştir. Çalışma, ark kullanımının lazer ve elektron ışınına alternatif olarak uygulanabilirliğini ortaya koymakta ve işlem parametrelerinin optimizasyonu için önemli bulgular sunmaktadır.
- 1 September 2021
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 24 (3) , 903-914
Seçimli Lazer Ergitme İle Ti6Al4V ELI Alaşımından Üretilen Trabeküler Metal Yapıların Basma Ve Basma-Kayma Dayanımlarının İncelenmesi
Üretildiği malzemenin dayanım, biyolojik ve yorulma gibi özelliklerini kullanım alanına uygun olarak şartlandırabilen gözenekli yapılara ortopedi alanında özellikle onarıcı biyomedikal ürün üretimi için gereksinim duyulmaya başlanmıştır. Dolu malzemelerin kemik ile dayanım farkının fazla olması sonucu ortaya çıkan gerilme kalkanı etkisi biyomedikal ürün kaybına sebep olmaktadır. Eklemeli imalat yöntemlerinin sağladığı avantaj sayesinde gözenekli malzemeler koşullara uygun olarak tasarlanabilmekte veya doğal yapıya sahip geometrilerin kopyalanması ile üretim yapılabilmektedir. Literatürün genelinde yer alan tasarlanabilir birim hücre geometrilerinin üretilebilirliği ve dayanımı hakkındaki çalışmaların aksine yapılan çalışmada koyuna ait femur ve vertebra bölgelerinden alınan trabeküler kemiklerin Mikro-CT ile kopyalanması sonucu elde edilen geometriler Ti6Al4V ELI alaşımından seçimli lazer ergitme (SLE) metodu ile üretilmiştir. Yapılan üretimlerin basma ve basma-kayma dayanımları incelenmiştir. Destek yapılar kullanılmadan yapılan üretim sonrası karşılaşılabilecek üretim değişimleri göz önünde bulundurularak trabeküler yapının üretiminde 1:1, 1:1,10 ve 1:1,20 ölçekli geometriler kullanılmıştır. Yapılan basma testleri sonucunda elastisite modül femur numunelerinde ortalama 3±0,25 GPa ve vertebra numunelerinde 2±0,15 GPa olarak elde edilmiş olup analizlerin deney sonuçları ile uyumluluğunun yüksek olduğu görülmüştür. Çalışma kapsamında üretilen trabeküler metal yapının biyomedikal ürünlerde kullanılması durumunda sahip olduğu düşük elastisite modül değerleriyle gerilme kalkanı etkisini azaltacağı ve doğal kemik geometrisi avantajı ile kemiğin içe doğru büyüme davranışını destekleyeceği sonucuna varılmıştır.
- 1 September 2021
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 24 (3) , 903-914
Seçimli Lazer Ergitme İle Ti6Al4V ELI Alaşımından Üretilen Trabeküler Metal Yapıların Basma Ve Basma-Kayma Dayanımlarının İncelenmesi
Üretildiği malzemenin dayanım, biyolojik ve yorulma gibi özelliklerini kullanım alanına uygun olarak şartlandırabilen gözenekli yapılara ortopedi alanında özellikle onarıcı biyomedikal ürün üretimi için gereksinim duyulmaya başlanmıştır. Dolu malzemelerin kemik ile dayanım farkının fazla olması sonucu ortaya çıkan gerilme kalkanı etkisi biyomedikal ürün kaybına sebep olmaktadır. Eklemeli imalat yöntemlerinin sağladığı avantaj sayesinde gözenekli malzemeler koşullara uygun olarak tasarlanabilmekte veya doğal yapıya sahip geometrilerin kopyalanması ile üretim yapılabilmektedir. Literatürün genelinde yer alan tasarlanabilir birim hücre geometrilerinin üretilebilirliği ve dayanımı hakkındaki çalışmaların aksine yapılan çalışmada koyuna ait femur ve vertebra bölgelerinden alınan trabeküler kemiklerin Mikro-CT ile kopyalanması sonucu elde edilen geometriler Ti6Al4V ELI alaşımından seçimli lazer ergitme (SLE) metodu ile üretilmiştir. Yapılan üretimlerin basma ve basma-kayma dayanımları incelenmiştir. Destek yapılar kullanılmadan yapılan üretim sonrası karşılaşılabilecek üretim değişimleri göz önünde bulundurularak trabeküler yapının üretiminde 1:1, 1:1,10 ve 1:1,20 ölçekli geometriler kullanılmıştır. Yapılan basma testleri sonucunda elastisite modül femur numunelerinde ortalama 3±0,25 GPa ve vertebra numunelerinde 2±0,15 GPa olarak elde edilmiş olup analizlerin deney sonuçları ile uyumluluğunun yüksek olduğu görülmüştür. Çalışma kapsamında üretilen trabeküler metal yapının biyomedikal ürünlerde kullanılması durumunda sahip olduğu düşük elastisite modül değerleriyle gerilme kalkanı etkisini azaltacağı ve doğal kemik geometrisi avantajı ile kemiğin içe doğru büyüme davranışını destekleyeceği sonucuna varılmıştır.
- 3 January 2021
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 46 (3) , 2527-2541
Reproducibility of Replicated Trabecular Bone Structures from Ti6Al4V Extralow Interstitials Powder by Selective Laser Melting
- 3 January 2021
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 46 (3) , 2527-2541
Reproducibility of Replicated Trabecular Bone Structures from Ti6Al4V Extralow Interstitials Powder by Selective Laser Melting
- 1 March 2020
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 14 (1) , 323-343
A knowledge-based material selection system for interactive pressure vessel design
- 1 March 2020
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 14 (1) , 323-343
A knowledge-based material selection system for interactive pressure vessel design
- 8 March 2018
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 33 (1) , 115-125
Basınçlı kaplarda malzeme seçimine yönelik bir karar destek sisteminin geliştirilmesi
Malzeme alanında kullanılan yöntemlerde oluşan gelişmeler ve sürekli artan malzeme çeşitliliği malzeme seçiminde yeni yaklaşımlar kullanılmasını gerekli hale getirmiştir. Bu makalede basınçlı kaplarda verilen malzeme seçim kararlarını daha sistematik ve kapsayıcı yapmak için MATSEL olarak adlandırılan bir karar destek sistemi geliştirilmiştir. İki aşamalı bir yapısı olan MATSEL ilk aşamada bir ön eleme işlemi yaparak verilen basınçlı kap parçasının tanımlanan koşullarına göre aday malzemeleri belirler. İkinci aşamada ise çok kriterli karar verme yöntemleri olan TOPSIS, ELECTRE ve VIKOR ile aday malzemeler arasında sıralamalar oluşturulur. Her aday malzeme için üç ayrı yöntemdeki sıralamaların toplamı aday malzemenin kullanıcıya hangi sırada önerileceğini belirler. En düşük toplam notu alan aday malzeme kullanıcıya ilk sırada önerilir. Çalışmada ayrıca sıralamalar arasındaki istatiksel benzerlik Spearman Sıra İlişkisi Testi kullanılarak ölçülmüştür ve farklılıkların nedenleri incelenmiştir. MATSEL’in aralarından seçim yapabilmesi için oluşturulan malzeme veritabanında bulunan malzemeler ve özellikleri ASME (American Society of Mechanical Engineers) ve CES (Cambridge Engiineering Selection) katologları kullanılarak elde edilmiştir.
- 8 March 2018
- Published by Journal of the Faculty of Engineering and Architecture of Gazi University in Gazi Üniversitesi Mühendislik-Mimarlık Fakültesi Dergisi
- Vol. 33 (1) , 115-125
Basınçlı kaplarda malzeme seçimine yönelik bir karar destek sisteminin geliştirilmesi
Malzeme alanında kullanılan yöntemlerde oluşan gelişmeler ve sürekli artan malzeme çeşitliliği malzeme seçiminde yeni yaklaşımlar kullanılmasını gerekli hale getirmiştir. Bu makalede basınçlı kaplarda verilen malzeme seçim kararlarını daha sistematik ve kapsayıcı yapmak için MATSEL olarak adlandırılan bir karar destek sistemi geliştirilmiştir. İki aşamalı bir yapısı olan MATSEL ilk aşamada bir ön eleme işlemi yaparak verilen basınçlı kap parçasının tanımlanan koşullarına göre aday malzemeleri belirler. İkinci aşamada ise çok kriterli karar verme yöntemleri olan TOPSIS, ELECTRE ve VIKOR ile aday malzemeler arasında sıralamalar oluşturulur. Her aday malzeme için üç ayrı yöntemdeki sıralamaların toplamı aday malzemenin kullanıcıya hangi sırada önerileceğini belirler. En düşük toplam notu alan aday malzeme kullanıcıya ilk sırada önerilir. Çalışmada ayrıca sıralamalar arasındaki istatiksel benzerlik Spearman Sıra İlişkisi Testi kullanılarak ölçülmüştür ve farklılıkların nedenleri incelenmiştir. MATSEL’in aralarından seçim yapabilmesi için oluşturulan malzeme veritabanında bulunan malzemeler ve özellikleri ASME (American Society of Mechanical Engineers) ve CES (Cambridge Engiineering Selection) katologları kullanılarak elde edilmiştir.