Mustafa Söyler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mustafa Söyler has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Coskun Özalp
Osmaniye Korkut Ata Üniversitesi
7 shared publications - Doğan Burak SAYDAM
OSMANİYE KORKUT ATA ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ, ENERJİ SİSTEMLERİ MÜHENDİSLİĞİ BÖLÜMÜ
6 shared publications - Cemre Polat
Osmaniye Korkut Ata University, Duzici Vocational High School, Motor Vehicles and Transport Technology
5 shared publications - Bulent Yaniktepe
Osmaniye Korkut Ata Üniversitesi
1 shared publication Cemre Polat
Osmaniye Korkut Ata Üniversitesi
1 shared publication- Ertuğrul ŞEKEROĞLU
Osmaniye Korkut Ata University
1 shared publication
Latest Publications
- 15 October 2026
- Published by Elsevier in Ocean Engineering
- Vol. 369
Experimental investigation of the flow structure in the horseshoe vortex region of a circular cylinder at different rotation rates
- 15 October 2026
- Published by Elsevier in Ocean Engineering
- Vol. 369
Experimental investigation of the flow structure in the horseshoe vortex region of a circular cylinder at different rotation rates
- 30 September 2026
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 14 (3) , 1490-1501
Numerical Investigation of Thermo-Hydraulic Performance of Staggered Cam-Shaped Tube Bundles
In this study, the thermo-hydraulic performance of staggered cam-shaped tube bundles under crossflow conditions was numerically investigated. The steady-state Reynolds-averaged Navier Stokes equations were solved using the RNG k-ε turbulence model with enhanced wall treatment. Thirteen configurations (Models M1-M13) were analyzed over a Reynolds number range of 4000–32000. The geometric parameters included the leading-edge diameter (d = 2.5, 5, and 7.5 mm) and the distance between the centers of the two circles (L = 10, 12.5, 15, and 17.5 mm), corresponding to aspect ratios (AR) of 1.00–2.63. The velocity, pressure, and turbulent kinetic energy distributions showed that the cam-shaped geometries modified the downstream flow field and reduced flow resistance compared with the baseline circular tube bundle. The average Nusselt number increased with Reynolds number but generally decreased with increasing d and L, whereas the friction factor decreased as these geometric parameters increased. All cam-shaped configurations exhibited lower friction factors than the baseline circular tube bundle (M1) and performance evaluation criterion (PEC) values greater than unity throughout the investigated Reynolds-number range. Among the investigated configurations, Model M13 (AR = 2.63, d = 7.5 mm, L = 17.5 mm) provided the highest thermo-hydraulic performance, achieving an approximately 28% improvement in PEC compared with the baseline model.
- 30 September 2026
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 14 (3) , 1490-1501
Numerical Investigation of Thermo-Hydraulic Performance of Staggered Cam-Shaped Tube Bundles
In this study, the thermo-hydraulic performance of staggered cam-shaped tube bundles under crossflow conditions was numerically investigated. The steady-state Reynolds-averaged Navier Stokes equations were solved using the RNG k-ε turbulence model with enhanced wall treatment. Thirteen configurations (Models M1-M13) were analyzed over a Reynolds number range of 4000–32000. The geometric parameters included the leading-edge diameter (d = 2.5, 5, and 7.5 mm) and the distance between the centers of the two circles (L = 10, 12.5, 15, and 17.5 mm), corresponding to aspect ratios (AR) of 1.00–2.63. The velocity, pressure, and turbulent kinetic energy distributions showed that the cam-shaped geometries modified the downstream flow field and reduced flow resistance compared with the baseline circular tube bundle. The average Nusselt number increased with Reynolds number but generally decreased with increasing d and L, whereas the friction factor decreased as these geometric parameters increased. All cam-shaped configurations exhibited lower friction factors than the baseline circular tube bundle (M1) and performance evaluation criterion (PEC) values greater than unity throughout the investigated Reynolds-number range. Among the investigated configurations, Model M13 (AR = 2.63, d = 7.5 mm, L = 17.5 mm) provided the highest thermo-hydraulic performance, achieving an approximately 28% improvement in PEC compared with the baseline model.
- 3 November 2025
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 150 (23) , 19189-19202
Numerical simulation of the thermal–hydraulic performance of the longitudinal triangular finned tube bank intermediate heat exchanger
- 3 November 2025
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 150 (23) , 19189-19202
Numerical simulation of the thermal–hydraulic performance of the longitudinal triangular finned tube bank intermediate heat exchanger
- 30 September 2023
- Published by Springer Nature
- p. 77-81
Dye Visualization of Flow Structure of a Circular Cylinder Oscillating at Re = 1000
- 30 September 2023
- Published by Springer Nature
- p. 77-81
Dye Visualization of Flow Structure of a Circular Cylinder Oscillating at Re = 1000
- 1 March 2022
- Published by Konya Muhendislik Bilimleri Dergisi in Konya Journal of Engineering Sciences
- Vol. 10 (1) , 200-214
Experimental Investigation of The Effect of Placing Dual Cube Models in The Flow Field with Different Gap Ratios on Flow Structure
Küp şeklindeki cisimlerin birbiri ile konumlandırılması cisimlerin etrafındaki akış yapısından kaynaklanan akış etkileri açısından önemlidir. Cisimlerin yerleşimi faydalı rüzgâr akımı yaratabileceği gibi istenmeyen rüzgâr akımı meydan getirerek cisimlerde yapısal titreşimler ve gürültü gibi istenmeyen durumları da meydana getirebilmektedir. Bu çalışmada akrilik malzemeden, 75x75mm boyutlarında imal edilen küp cisim modelleri, aralarında farklı açıklık oranlarında (D/h = 0.5, 1 ve 2) olacak şekilde konumlandırılmıştır. D küpler arasındaki mesafeyi, h küpün kenar uzunluğunu ifade etmektedir. Kullanılan modellerin karakteristik çapına (h) ve akış hızına (V) bağlı olarak deneyler Reynolds sayısı, Re=26000’de gerçekleştirilmiştir. Parçacık Görüntüleme Hız Ölçüm Tekniği (PIV) kullanılarak anlık olarak elde edilen hız vektörleri ile anlık girdap, akım çizgisi gibi bileşenler hesaplanmış ve hesaplanan anlık verilerle de zaman ortalama hız, girdap ve türbülans istatistikleri belirlenmiştir. Çalışma sonucunda, ayrılmış akış bölgesinin D/h oranının artması ile daha geniş bir alana yayıldığı görülmektedir. D/h oranının artması ile hız bileşeninin dalgalanmalarının azaldığı, modeller arasındaki D/h oranının azalması ile iki model arasında kalan bölgede akış hızının arttığı tespit edilmiştir.
- 1 March 2022
- Published by Konya Muhendislik Bilimleri Dergisi in Konya Journal of Engineering Sciences
- Vol. 10 (1) , 200-214
Experimental Investigation of The Effect of Placing Dual Cube Models in The Flow Field with Different Gap Ratios on Flow Structure
Küp şeklindeki cisimlerin birbiri ile konumlandırılması cisimlerin etrafındaki akış yapısından kaynaklanan akış etkileri açısından önemlidir. Cisimlerin yerleşimi faydalı rüzgâr akımı yaratabileceği gibi istenmeyen rüzgâr akımı meydan getirerek cisimlerde yapısal titreşimler ve gürültü gibi istenmeyen durumları da meydana getirebilmektedir. Bu çalışmada akrilik malzemeden, 75x75mm boyutlarında imal edilen küp cisim modelleri, aralarında farklı açıklık oranlarında (D/h = 0.5, 1 ve 2) olacak şekilde konumlandırılmıştır. D küpler arasındaki mesafeyi, h küpün kenar uzunluğunu ifade etmektedir. Kullanılan modellerin karakteristik çapına (h) ve akış hızına (V) bağlı olarak deneyler Reynolds sayısı, Re=26000’de gerçekleştirilmiştir. Parçacık Görüntüleme Hız Ölçüm Tekniği (PIV) kullanılarak anlık olarak elde edilen hız vektörleri ile anlık girdap, akım çizgisi gibi bileşenler hesaplanmış ve hesaplanan anlık verilerle de zaman ortalama hız, girdap ve türbülans istatistikleri belirlenmiştir. Çalışma sonucunda, ayrılmış akış bölgesinin D/h oranının artması ile daha geniş bir alana yayıldığı görülmektedir. D/h oranının artması ile hız bileşeninin dalgalanmalarının azaldığı, modeller arasındaki D/h oranının azalması ile iki model arasında kalan bölgede akış hızının arttığı tespit edilmiştir.
- Open Access
- 20 December 2021
- Published by European Mechanical Science in European Mechanical Science
- Vol. 5 (4) , 153-160
An Experimental Investigation of the Flow Structure on a Face Mannequin With / Without a Face Shield
This study investigated experimentally the flow regime with a face shield on a face mannequin placed at different distances (L=50 cm and L=150 cm to source of flow), i.e., perpendicular to the channel or at an angle of 10°, through the PIV (Particle Imaging Velocimetry) method along with the dye experiments, based on which the face shield and dye injector were positioned to conduct the PIV tests. As a result of the experiments, instantaneous velocity vectors and velocity magnitude data were obtained, and the flow structure around the face shield was examined in detail. The study revealed that the flow released through the respiratory tract hit the face and eye area of the mannequin in the experiments performed without using a face shield, yet, with the face shield, the flow that emerged while talking at a close distance was directed from the lower part of the face shield towards the neck and jaw but protected the face and eye area compared to the case without a face shield. It was observed that the flow lost its energy when it first left the flow source, and the velocity vectors were directed down the neck area. Positioning the mannequin at an angle of 10° turned out to be less protective than positioning it perpendicular to the channel, due to the flow being directed from the jaw to the mouth area with the effect of the angle.
- 20 December 2021
- Published by European Mechanical Science in European Mechanical Science
- Vol. 5 (4) , 153-160
Open AccessAn Experimental Investigation of the Flow Structure on a Face Mannequin With / Without a Face Shield
This study investigated experimentally the flow regime with a face shield on a face mannequin placed at different distances (L=50 cm and L=150 cm to source of flow), i.e., perpendicular to the channel or at an angle of 10°, through the PIV (Particle Imaging Velocimetry) method along with the dye experiments, based on which the face shield and dye injector were positioned to conduct the PIV tests. As a result of the experiments, instantaneous velocity vectors and velocity magnitude data were obtained, and the flow structure around the face shield was examined in detail. The study revealed that the flow released through the respiratory tract hit the face and eye area of the mannequin in the experiments performed without using a face shield, yet, with the face shield, the flow that emerged while talking at a close distance was directed from the lower part of the face shield towards the neck and jaw but protected the face and eye area compared to the case without a face shield. It was observed that the flow lost its energy when it first left the flow source, and the velocity vectors were directed down the neck area. Positioning the mannequin at an angle of 10° turned out to be less protective than positioning it perpendicular to the channel, due to the flow being directed from the jaw to the mouth area with the effect of the angle.
- Open Access
- 15 December 2021
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 4 (3) , 431-440
Dönen Bir Silindir Etrafındaki Akış Yapısının PIV Yöntemi ile Deneysel Olarak İncelenmesi
Bu çalışmada 25 mm çaplı düz yüzeyli bir silindire saat yönü ve saatin tersi yönünde farklı dönme oranları (α=0.5, 1, 1.5, 2, 4) uygulandığında silindir etrafında oluşan akış yapısı deneysel olarak incelenmiştir. Öncelikle silindirin sabit olduğu durum için deneyler gerçekleştirilmiş, daha sonra da silindire farklı hızlarda ve yönlerde silindirin merkezinden dönme hareketi verilerek silindir etrafındaki akış yapısının değişimi incelenmiştir. Düşük dönme oranlarının (α) akış kontrolünde yetersiz olduğu, dönme oranının artması ile akış kontrol etkinliğinin arttığı görülmüştür. Sonuç olarak, düşük dönüş hızlarında silindirin dönme oranının olmadığı duruma benzer girdaplar oluşmaya başlamış ve Karman girdap caddesi dönme yönüne doğru sapmıştır. Fakat dönmenin etkisiyle oluşan girdapların küçülmesi Karman girdap caddesi boyutunu dönmeyen silindire göre daralmıştır. Yüksek dönme oranlarında sınır tabaka ayrılmasının ötelendiği, ölü akış bölgesinin silindire doğru daraldığı ve akış yönünde oluşan Karman girdap caddesinin oluşmadığı gözlenmiştir. Yüksek dönme oranları akış yönünde oluşan girdap kopmalarının tamamıyla ortadan kaybolmasına ve akışın dönme yönüne doğru bozulmadan ilerlemesine neden olmuştur.
- 15 December 2021
- Published by Osmaniye Korkut Ata Universitesi in Osmaniye Korkut Ata Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 4 (3) , 431-440
Open AccessDönen Bir Silindir Etrafındaki Akış Yapısının PIV Yöntemi ile Deneysel Olarak İncelenmesi
Bu çalışmada 25 mm çaplı düz yüzeyli bir silindire saat yönü ve saatin tersi yönünde farklı dönme oranları (α=0.5, 1, 1.5, 2, 4) uygulandığında silindir etrafında oluşan akış yapısı deneysel olarak incelenmiştir. Öncelikle silindirin sabit olduğu durum için deneyler gerçekleştirilmiş, daha sonra da silindire farklı hızlarda ve yönlerde silindirin merkezinden dönme hareketi verilerek silindir etrafındaki akış yapısının değişimi incelenmiştir. Düşük dönme oranlarının (α) akış kontrolünde yetersiz olduğu, dönme oranının artması ile akış kontrol etkinliğinin arttığı görülmüştür. Sonuç olarak, düşük dönüş hızlarında silindirin dönme oranının olmadığı duruma benzer girdaplar oluşmaya başlamış ve Karman girdap caddesi dönme yönüne doğru sapmıştır. Fakat dönmenin etkisiyle oluşan girdapların küçülmesi Karman girdap caddesi boyutunu dönmeyen silindire göre daralmıştır. Yüksek dönme oranlarında sınır tabaka ayrılmasının ötelendiği, ölü akış bölgesinin silindire doğru daraldığı ve akış yönünde oluşan Karman girdap caddesinin oluşmadığı gözlenmiştir. Yüksek dönme oranları akış yönünde oluşan girdap kopmalarının tamamıyla ortadan kaybolmasına ve akışın dönme yönüne doğru bozulmadan ilerlemesine neden olmuştur.
- 31 December 2020
- Published by International Journal of Energy Applications and Technologies in International Journal of Energy Applications and Technologies
- Vol. 7 (4) , 126-133
Experimental flow analysis of vertical axis turbine for power generation in open channel system
In this experimental study, flow structure over a three bladed vertical axis Darrieus turbine is investigated experimentally for Reynold Number, Re=9000 in an open channel. Rigidity ratio (σ), angle of attack, optimum values of blade chord length (CL), turbine radius (R) and height of turbine blades (H) are used as approximately 1.1 and α=-2°, CL=5 cm, R=13.75 cm and H=20 cm, respectively. According to the values, ¼ scale model of a vertical axis Darrieus turbine has been used in order to perform experimental flow analysis. In experimental flow analysis, two different azimuth angles, θ=270° and θ=240° are used to examine the flow characteristics in the Particle İmage Velocimetry (PIV) experiments. As a result of the experiments, time averaged velocity vectors , averaged streamlines , and averaged vortex fields , are obtained and interpreted time averaged velocity vectors , averaged streamlines , and averaged vortex fields , changes with the turbine blade positions. As a result, it is seen that turbine azimuthal angle affetcs the flow structure and streamline focal points, positive and negative vortex are formed in the flow region behind the turbine. Only one focal point at θ=240° is occurred while two focal points and one stagnation point are occurred at the angle of θ=270°.
- 31 December 2020
- Published by International Journal of Energy Applications and Technologies in International Journal of Energy Applications and Technologies
- Vol. 7 (4) , 126-133
Experimental flow analysis of vertical axis turbine for power generation in open channel system
In this experimental study, flow structure over a three bladed vertical axis Darrieus turbine is investigated experimentally for Reynold Number, Re=9000 in an open channel. Rigidity ratio (σ), angle of attack, optimum values of blade chord length (CL), turbine radius (R) and height of turbine blades (H) are used as approximately 1.1 and α=-2°, CL=5 cm, R=13.75 cm and H=20 cm, respectively. According to the values, ¼ scale model of a vertical axis Darrieus turbine has been used in order to perform experimental flow analysis. In experimental flow analysis, two different azimuth angles, θ=270° and θ=240° are used to examine the flow characteristics in the Particle İmage Velocimetry (PIV) experiments. As a result of the experiments, time averaged velocity vectors , averaged streamlines , and averaged vortex fields , are obtained and interpreted time averaged velocity vectors , averaged streamlines , and averaged vortex fields , changes with the turbine blade positions. As a result, it is seen that turbine azimuthal angle affetcs the flow structure and streamline focal points, positive and negative vortex are formed in the flow region behind the turbine. Only one focal point at θ=240° is occurred while two focal points and one stagnation point are occurred at the angle of θ=270°.
- Open Access
- 20 December 2020
- Published by European Mechanical Science in European Mechanical Science
- Vol. 4 (4) , 185-189
Dye Injection Flow Visualization Around a Rotating Circular Cylinder
In this study, the visualization of the flow structure around a circular cylinder was investigated with dye injection experiments. The experiments were carried out in the closed-circuit open water channel in Osmaniye Korkut Ata University. Experiments have been studied on a circular cylinder at different rotational speeds. Experiments were carried out at Re = 1000 according to cylinder diameter and free stream velocity. In the study, with the increase of the rotation speed, an acceleration layer occurs between the fluid velocity in the cylinder wake in the flow direction and the flow from the circumference of the cylinder and the speed of rotation. This situation caused the complete disappearance of the vortex ruptures in the flow direction and the emergence of Kelvin Helmhotz fluctuations. As a result of the study, it is seen that the flow control is insufficient at low rotational speeds, but the flow can be controllable at high rotational speeds.
- 20 December 2020
- Published by European Mechanical Science in European Mechanical Science
- Vol. 4 (4) , 185-189
Open AccessDye Injection Flow Visualization Around a Rotating Circular Cylinder
In this study, the visualization of the flow structure around a circular cylinder was investigated with dye injection experiments. The experiments were carried out in the closed-circuit open water channel in Osmaniye Korkut Ata University. Experiments have been studied on a circular cylinder at different rotational speeds. Experiments were carried out at Re = 1000 according to cylinder diameter and free stream velocity. In the study, with the increase of the rotation speed, an acceleration layer occurs between the fluid velocity in the cylinder wake in the flow direction and the flow from the circumference of the cylinder and the speed of rotation. This situation caused the complete disappearance of the vortex ruptures in the flow direction and the emergence of Kelvin Helmhotz fluctuations. As a result of the study, it is seen that the flow control is insufficient at low rotational speeds, but the flow can be controllable at high rotational speeds.
- 2 February 2018
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 21 (1) , 13-+
Isı Transferi Akışkanı Olarak Eriyik Tuz Kullanılan Bir Gövde Boru Tipi Isı Değiştiricisinin Hesaplamalı Akışkanlar Dinamiği Programı ile Analizi
Bu çalışmada eriyik tuz kullanılan bir gövde borulu ısı değiştiricisinin ısı transfer performansı bir hesaplamalı akışkanlar dinamiği (HAD) programıyla analiz edilmiştir. Bu çalışma literatürde yapılan bir deneyi doğrulamak için gerçekleştirilmiştir. Ticari bir HAD programı olan ANSYS Fluent 14.5 sürümü bu çalışmada kullanılmıştır. Eriyik tuz ısı değiştiricisine farklı sıcaklık aralıklarında (360 ˚C – 400 ˚C) ve farklı debilerde (0,48 – 1,87 m 3 /h) girmektedir. Elde edilen sayısal sonuçlar ile literatürden seçilen çalışmadaki deneysel sonuçlarla karşılaştırılmıştır ve iyi bir uyum sağlandığı görülmüştür. Bu çalışmada geliştirilen sayısal HAD modeli ileriki çalışmalarda kullanılabilecektir.
- 2 February 2018
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 21 (1) , 13-+
Isı Transferi Akışkanı Olarak Eriyik Tuz Kullanılan Bir Gövde Boru Tipi Isı Değiştiricisinin Hesaplamalı Akışkanlar Dinamiği Programı ile Analizi
Bu çalışmada eriyik tuz kullanılan bir gövde borulu ısı değiştiricisinin ısı transfer performansı bir hesaplamalı akışkanlar dinamiği (HAD) programıyla analiz edilmiştir. Bu çalışma literatürde yapılan bir deneyi doğrulamak için gerçekleştirilmiştir. Ticari bir HAD programı olan ANSYS Fluent 14.5 sürümü bu çalışmada kullanılmıştır. Eriyik tuz ısı değiştiricisine farklı sıcaklık aralıklarında (360 ˚C – 400 ˚C) ve farklı debilerde (0,48 – 1,87 m 3 /h) girmektedir. Elde edilen sayısal sonuçlar ile literatürden seçilen çalışmadaki deneysel sonuçlarla karşılaştırılmıştır ve iyi bir uyum sağlandığı görülmüştür. Bu çalışmada geliştirilen sayısal HAD modeli ileriki çalışmalarda kullanılabilecektir.