Dennis Braun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dennis Braun has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Joachim Mayer
Forschungszentrum Jülich GmbH
9 shared publications - Lukas Völkel
Chair of Electronic Devices (ELD) RWTH Aachen University Aachen Germany
9 shared publications - Max Christian Lemme
Chair of Electronic Devices, RWTH Aachen University, Aachen, Germany
9 shared publications - Jimin Lee
Chair of Electronic Devices (ELD) RWTH Aachen University Aachen Germany
8 shared publications - Sofía Cruces
Chair of Electronic Devices (ELD) RWTH Aachen University Aachen Germany
8 shared publications - Alwin Daus
Chair of Electronic Devices RWTH Aachen University Otto‐Blumenthal‐Str. 25 52074 Aachen Germany
7 shared publications
Latest Publications
- 3 October 2026
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 8 (20) , 9031-9040
Influence of Metal–Organic Chemical Vapor Deposition MoS2 Material Properties on Memristor Resistance State and Switching Voltage Variability
Two-dimensional (2D) materials are promising resistive switching materials for vertical memristors due to their ultimate thinness and low-power operation. However, high electrical variability remains a challenge, and reducing it through materials engineering remains largely unexplored. Here, we investigate how the properties of 2D multilayer molybdenum disulfide (MoS2), grown by metal–organic chemical vapor deposition (MOCVD), influence variability in memristors with metal electrodes. Two MoS2 batches were prepared under different MOCVD growth conditions, resulting in distinct surface roughness and grain sizes. Devices based on smoother, more uniform MoS2 with larger grains exhibited significantly reduced electrical variability. Based on established grain-boundary-assisted filament models, the larger crystallites provide a plausible explanation for the reduced variability, although the contributions of individual material properties cannot be separated in the present comparison. More than 60 devices per batch were tested, providing a robust statistical basis. These results show that optimizing MoS2 grain size and uniformity can improve memristor reliability and highlight the potential of MOCVD as a scalable route toward improved statistical uniformity in MoS2 films.
- 3 October 2026
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 8 (20) , 9031-9040
Influence of Metal–Organic Chemical Vapor Deposition MoS2 Material Properties on Memristor Resistance State and Switching Voltage Variability
Two-dimensional (2D) materials are promising resistive switching materials for vertical memristors due to their ultimate thinness and low-power operation. However, high electrical variability remains a challenge, and reducing it through materials engineering remains largely unexplored. Here, we investigate how the properties of 2D multilayer molybdenum disulfide (MoS2), grown by metal–organic chemical vapor deposition (MOCVD), influence variability in memristors with metal electrodes. Two MoS2 batches were prepared under different MOCVD growth conditions, resulting in distinct surface roughness and grain sizes. Devices based on smoother, more uniform MoS2 with larger grains exhibited significantly reduced electrical variability. Based on established grain-boundary-assisted filament models, the larger crystallites provide a plausible explanation for the reduced variability, although the contributions of individual material properties cannot be separated in the present comparison. More than 60 devices per batch were tested, providing a robust statistical basis. These results show that optimizing MoS2 grain size and uniformity can improve memristor reliability and highlight the potential of MOCVD as a scalable route toward improved statistical uniformity in MoS2 films.
- Open Access
- 30 April 2026
- Published by Wiley in Advanced Electronic Materials
- Vol. 12 (18)
Influence of Top Electrode Metal on Resistive Switching in Multilayer MOCVD MoS 2 Memristors
Two‐dimensional (2D) materials such as molybdenum disulfide (MoS 2 ) show promise for memristor applications. Most MoS 2 memristors use vertical metal/MoS 2 /metal stacks with gold or silver active electrodes and rely on electron‐beam evaporation; sputtering is seldom used. This study investigates palladium (Pd), nickel (Ni), and aluminum (Al) as electrodes and compares resistive switching (RS) performance for sputtered versus evaporated top electrodes. Pd acts as a passive electrode with minimal contribution to RS. Devices with Ni active electrodes exhibit very low initial resistance and a small RS window, consistent with deposition‐induced damage to MoS 2 . Sputtered Al yields highly reproducible RS in Pd/MoS 2 /Al memristors, achieving 95% yield across 64 devices. In contrast, evaporated Al forms a parasitic oxide at the Al/MoS 2 interface that inhibits RS, even when deposited at a base pressure comparable to that of sputtered Al. Area scaling and temperature‐dependent measurements indicate Al filament formation and dissolution via electrochemical metallization as the RS mechanism. Metal‐specific energy barriers for filament formation explain the superior performance of sputtered Al. Overall, the results identify Al as an effective active electrode within the investigated device architecture and show that sputtering is a viable alternative for top‐electrode deposition because it suppresses interfacial oxide formation.
- 30 April 2026
- Published by Wiley in Advanced Electronic Materials
- Vol. 12 (18)
Open AccessInfluence of Top Electrode Metal on Resistive Switching in Multilayer MOCVD MoS 2 Memristors
Two‐dimensional (2D) materials such as molybdenum disulfide (MoS 2 ) show promise for memristor applications. Most MoS 2 memristors use vertical metal/MoS 2 /metal stacks with gold or silver active electrodes and rely on electron‐beam evaporation; sputtering is seldom used. This study investigates palladium (Pd), nickel (Ni), and aluminum (Al) as electrodes and compares resistive switching (RS) performance for sputtered versus evaporated top electrodes. Pd acts as a passive electrode with minimal contribution to RS. Devices with Ni active electrodes exhibit very low initial resistance and a small RS window, consistent with deposition‐induced damage to MoS 2 . Sputtered Al yields highly reproducible RS in Pd/MoS 2 /Al memristors, achieving 95% yield across 64 devices. In contrast, evaporated Al forms a parasitic oxide at the Al/MoS 2 interface that inhibits RS, even when deposited at a base pressure comparable to that of sputtered Al. Area scaling and temperature‐dependent measurements indicate Al filament formation and dissolution via electrochemical metallization as the RS mechanism. Metal‐specific energy barriers for filament formation explain the superior performance of sputtered Al. Overall, the results identify Al as an effective active electrode within the investigated device architecture and show that sputtering is a viable alternative for top‐electrode deposition because it suppresses interfacial oxide formation.
- Open Access
- 12 March 2026
- Published by Wiley in Advanced Electronic Materials
- Vol. 12 (7) , e00800
Reduced Variability in Threshold Switches Using Heterostructures of SiO x and Vertically Aligned MoS 2
Two‐dimensional (2D) materials and their heterostructures offer promising pathways for intercalated ion migration and regulated filament growth in resistive switching (RS) devices, enabled by their van der Waals (vdW) gaps. In vertically aligned 2D materials, this vdW gap‐mediated ion transport holds great potential for high‐density integration and reliable RS performance for memristor crossbar arrays. However, the fundamental switching mechanisms and their contributions to the RS remain inadequately understood. In this work, we investigate silver (Ag) filament‐based threshold switching (TS) in heterostructures comprising vertically aligned 2D molybdenum disulfide (VAMoS 2 ) grown via sulfurization and silicon oxide (SiO x ). Compared to SiO x ‐only devices, the SiO x /VAMoS 2 devices exhibit TS with higher on‐threshold and hold voltages, each approximately 0.4 V, faster switching times down to 356 ns under a 4 V pulse, and a lower cycle‐to‐cycle on‐current variability of 3.0%. A physics‐based, variability‐aware model reveals that confined Ag ion migration within the vdW gaps in VAMoS 2 forms ultrathin seed filaments, which guide filament growth in the SiO x layer. These findings establish SiO x /VAMoS 2 heterostructures as a promising concept for reliable TS in vertical device architectures for emerging memories and neuromorphic computing.
- 12 March 2026
- Published by Wiley in Advanced Electronic Materials
- Vol. 12 (7) , e00800
Open AccessReduced Variability in Threshold Switches Using Heterostructures of SiO x and Vertically Aligned MoS 2
Two‐dimensional (2D) materials and their heterostructures offer promising pathways for intercalated ion migration and regulated filament growth in resistive switching (RS) devices, enabled by their van der Waals (vdW) gaps. In vertically aligned 2D materials, this vdW gap‐mediated ion transport holds great potential for high‐density integration and reliable RS performance for memristor crossbar arrays. However, the fundamental switching mechanisms and their contributions to the RS remain inadequately understood. In this work, we investigate silver (Ag) filament‐based threshold switching (TS) in heterostructures comprising vertically aligned 2D molybdenum disulfide (VAMoS 2 ) grown via sulfurization and silicon oxide (SiO x ). Compared to SiO x ‐only devices, the SiO x /VAMoS 2 devices exhibit TS with higher on‐threshold and hold voltages, each approximately 0.4 V, faster switching times down to 356 ns under a 4 V pulse, and a lower cycle‐to‐cycle on‐current variability of 3.0%. A physics‐based, variability‐aware model reveals that confined Ag ion migration within the vdW gaps in VAMoS 2 forms ultrathin seed filaments, which guide filament growth in the SiO x layer. These findings establish SiO x /VAMoS 2 heterostructures as a promising concept for reliable TS in vertical device architectures for emerging memories and neuromorphic computing.
- Open Access
- 20 February 2026
- Published by Wiley in Advanced Functional Materials
Integration of Low‐Voltage Nanoscale MoS 2 Memristors on CMOS Microchips
2D materials (2DMs) are gaining increased attention for applications such as advanced electronics and neuromorphic computing due to their excellent electrical properties. Among these 2DMs, molybdenum disulfide (MoS 2 ) has shown promise as a resistive switching (RS) layer for memory, selectors, and neuromorphic systems. Electrochemical metallization (ECM) devices based on 2DMs offer ultra‐low energy consumption, large ON/OFF ratios, and switching at sub‐nanometer thicknesses. However, most demonstrations rely on isolated, micrometer‐scale structures fabricated on SiO 2 /Si substrates. The integration of 2DM‐based memristors onto silicon complementary metal‐oxide‐semiconductor (CMOS) platforms is rarely reported, particularly for MoS 2 . This work presents the first nanoscale ∼0.015 µm 2 active area MoS 2 ‐based memristors integrated in the back‐end‐of‐line of 350 nm‐technology CMOS microchips. One‐transistor‐one‐resistor (1T1R) cells exhibited forming‐free, nonvolatile RS with ultra‐low operating voltages (∼0.23 V for the SET and ∼−0.1 V for the RESET) and low cycle‐to‐cycle variability (6.7%). We provide the current‐voltage ( I – V ) characteristics of 19 MoS 2 ‐based 1T1R cells, revealing high repeatability across multiple cycles and devices. Our work represents a significant step toward integrating MoS 2 ‐based nonvolatile memristive devices onto silicon CMOS microchips.
- 20 February 2026
- Published by Wiley in Advanced Functional Materials
Open AccessIntegration of Low‐Voltage Nanoscale MoS 2 Memristors on CMOS Microchips
2D materials (2DMs) are gaining increased attention for applications such as advanced electronics and neuromorphic computing due to their excellent electrical properties. Among these 2DMs, molybdenum disulfide (MoS 2 ) has shown promise as a resistive switching (RS) layer for memory, selectors, and neuromorphic systems. Electrochemical metallization (ECM) devices based on 2DMs offer ultra‐low energy consumption, large ON/OFF ratios, and switching at sub‐nanometer thicknesses. However, most demonstrations rely on isolated, micrometer‐scale structures fabricated on SiO 2 /Si substrates. The integration of 2DM‐based memristors onto silicon complementary metal‐oxide‐semiconductor (CMOS) platforms is rarely reported, particularly for MoS 2 . This work presents the first nanoscale ∼0.015 µm 2 active area MoS 2 ‐based memristors integrated in the back‐end‐of‐line of 350 nm‐technology CMOS microchips. One‐transistor‐one‐resistor (1T1R) cells exhibited forming‐free, nonvolatile RS with ultra‐low operating voltages (∼0.23 V for the SET and ∼−0.1 V for the RESET) and low cycle‐to‐cycle variability (6.7%). We provide the current‐voltage ( I – V ) characteristics of 19 MoS 2 ‐based 1T1R cells, revealing high repeatability across multiple cycles and devices. Our work represents a significant step toward integrating MoS 2 ‐based nonvolatile memristive devices onto silicon CMOS microchips.
- Open Access
- 30 December 2025
- Published by Wiley in Advanced Functional Materials
Intermediate Resistive State in Wafer‐Scale Vertical MoS 2 Memristors Through Lateral Silver Filament Growth for Artificial Synapse Applications
Memristors based on 2D materials have garnered significant attention. Their fast resistive switching (RS) behavior and atomic‐level thickness enable low power consumption, making them promising candidates for neuromorphic computing. Among these, memristors based on molybdenum disulfide (MoS 2 ) have been extensively studied. Their RS has been attributed to the formation and rupture of conductive filaments (CFs). However, the underlying mechanism of filament formation remains underexplored, and the inherently stochastic nature of RS leads to high variability and limited reproducibility. In this study, we demonstrate wafer‐scale memristors based on metal–organic chemical vapor‐deposited MoS 2 . Our devices exhibit both volatile and nonvolatile RS behaviors, tunable by modulating the current compliance. Notably, we observe stable RS characteristics in an intermediate resistive state (IRS), set and reset voltages within ±1 V, endurance of over 2500 cycles, and state retention over 10 6 s. Among 100 tested devices, 98 exhibited IRS behavior, confirming a high yield (98%) and demonstrating its robust and reproducible RS nature. Combined experimental and simulation results further indicate that the IRS arises from the lateral growth of CFs in the van der Waals gaps. Furthermore, the devices successfully emulate synaptic plasticity with current responses on a microsecond timescale, highlighting their potential for large‐scale integration in neuromorphic computing architectures.
- 30 December 2025
- Published by Wiley in Advanced Functional Materials
Open AccessIntermediate Resistive State in Wafer‐Scale Vertical MoS 2 Memristors Through Lateral Silver Filament Growth for Artificial Synapse Applications
Memristors based on 2D materials have garnered significant attention. Their fast resistive switching (RS) behavior and atomic‐level thickness enable low power consumption, making them promising candidates for neuromorphic computing. Among these, memristors based on molybdenum disulfide (MoS 2 ) have been extensively studied. Their RS has been attributed to the formation and rupture of conductive filaments (CFs). However, the underlying mechanism of filament formation remains underexplored, and the inherently stochastic nature of RS leads to high variability and limited reproducibility. In this study, we demonstrate wafer‐scale memristors based on metal–organic chemical vapor‐deposited MoS 2 . Our devices exhibit both volatile and nonvolatile RS behaviors, tunable by modulating the current compliance. Notably, we observe stable RS characteristics in an intermediate resistive state (IRS), set and reset voltages within ±1 V, endurance of over 2500 cycles, and state retention over 10 6 s. Among 100 tested devices, 98 exhibited IRS behavior, confirming a high yield (98%) and demonstrating its robust and reproducible RS nature. Combined experimental and simulation results further indicate that the IRS arises from the lateral growth of CFs in the van der Waals gaps. Furthermore, the devices successfully emulate synaptic plasticity with current responses on a microsecond timescale, highlighting their potential for large‐scale integration in neuromorphic computing architectures.
- Open Access
- 7 August 2025
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 25 (33) , 12455-12462
Volatile and Nonvolatile Resistive Switching in Lateral 2D Molybdenum Disulfide-Based Memristive Devices
Developing electronic devices capable of emulating biological functions is essential for advancing brain-inspired computation paradigms such as neuromorphic computing. In recent years, two-dimensional materials have emerged as promising candidates for neuromorphic electronic devices. This work addresses the coexistence of volatile and nonvolatile resistive switching in lateral memristors based on molybdenum disulfide with silver as the active electrode. The fabricated devices exhibited switching voltages of ∼0.16 V and ∼0.52 V for volatile and nonvolatile operation, respectively, under direct-current measurements. They also displayed the essential synaptic functions of paired-pulse facilitation and short- and long-term plasticity under pulse stimulation. The operation mechanism was investigated by in situ transmission electron microscopy, which showed lateral migration of silver ions along the molybdenum disulfide between electrodes. Based on the experimental data, a macroscopic semiclassical electron transport model was used to reproduce the current-voltage characteristics and support the proposed underlying switching mechanisms.
- 7 August 2025
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 25 (33) , 12455-12462
Open AccessVolatile and Nonvolatile Resistive Switching in Lateral 2D Molybdenum Disulfide-Based Memristive Devices
Developing electronic devices capable of emulating biological functions is essential for advancing brain-inspired computation paradigms such as neuromorphic computing. In recent years, two-dimensional materials have emerged as promising candidates for neuromorphic electronic devices. This work addresses the coexistence of volatile and nonvolatile resistive switching in lateral memristors based on molybdenum disulfide with silver as the active electrode. The fabricated devices exhibited switching voltages of ∼0.16 V and ∼0.52 V for volatile and nonvolatile operation, respectively, under direct-current measurements. They also displayed the essential synaptic functions of paired-pulse facilitation and short- and long-term plasticity under pulse stimulation. The operation mechanism was investigated by in situ transmission electron microscopy, which showed lateral migration of silver ions along the molybdenum disulfide between electrodes. Based on the experimental data, a macroscopic semiclassical electron transport model was used to reproduce the current-voltage characteristics and support the proposed underlying switching mechanisms.
- Open Access
- 4 May 2025
- Published by Wiley in Small Science
- Vol. 5 (5)
Volatile MoS2 Memristors with Lateral Silver Ion Migration for Artificial Neuron Applications
- 4 May 2025
- Published by Wiley in Small Science
- Vol. 5 (5)
Open AccessVolatile MoS2 Memristors with Lateral Silver Ion Migration for Artificial Neuron Applications
- Open Access
- 27 January 2025
- Published by Wiley in Small Science
- Vol. 5 (5)
Volatile MoS2 Memristors with Lateral Silver Ion Migration for Artificial Neuron Applications
Layered 2D semiconductors have shown enhanced ion migration capabilities along their van der Waals (vdW) gaps and on their surfaces. This effect can be employed for resistive switching (RS) in devices for emerging memories, selectors, and neuromorphic computing. To date, all lateral molybdenum disulfide (MoS2)‐based volatile RS devices with silver (Ag) ion migration have been demonstrated using exfoliated, single‐crystal MoS2 flakes requiring a forming step to enable RS. Herein, present volatile RS with multilayer MoS2 grown by metal‐organic chemical vapor deposition (MOCVD) with repeatable forming‐free operation is presented. The devices show highly reproducible volatile RS with low operating voltages of ≈2 V and fast‐switching times down to 130 ns considering their micrometer‐scale dimensions. The switching mechanism is investigated based on Ag ion surface migration through transmission electron microscopy, electronic transport modeling, and density functional theory. Finally, a physics‐based compact model is developed and the implementation of the volatile memristors as artificial neurons in neuromorphic systems is exploredd.
- 27 January 2025
- Published by Wiley in Small Science
- Vol. 5 (5)
Open AccessVolatile MoS2 Memristors with Lateral Silver Ion Migration for Artificial Neuron Applications
Layered 2D semiconductors have shown enhanced ion migration capabilities along their van der Waals (vdW) gaps and on their surfaces. This effect can be employed for resistive switching (RS) in devices for emerging memories, selectors, and neuromorphic computing. To date, all lateral molybdenum disulfide (MoS2)‐based volatile RS devices with silver (Ag) ion migration have been demonstrated using exfoliated, single‐crystal MoS2 flakes requiring a forming step to enable RS. Herein, present volatile RS with multilayer MoS2 grown by metal‐organic chemical vapor deposition (MOCVD) with repeatable forming‐free operation is presented. The devices show highly reproducible volatile RS with low operating voltages of ≈2 V and fast‐switching times down to 130 ns considering their micrometer‐scale dimensions. The switching mechanism is investigated based on Ag ion surface migration through transmission electron microscopy, electronic transport modeling, and density functional theory. Finally, a physics‐based compact model is developed and the implementation of the volatile memristors as artificial neurons in neuromorphic systems is exploredd.
- Open Access
- 5 May 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 34 (15)
Resistive Switching and Current Conduction Mechanisms in Hexagonal Boron Nitride Threshold Memristors with Nickel Electrodes
The 2D insulating material hexagonal boron nitride (h‐BN) has attracted much attention as the active medium in memristive devices due to its favorable physical properties, among others, a wide bandgap that enables a large switching window. Metal filament formation is frequently suggested for h‐BN devices as the resistive switching (RS) mechanism, usually supported by highly specialized methods like conductive atomic force microscopy (C‐AFM) or transmission electron microscopy (TEM). Here, the switching of multilayer hexagonal boron nitride (h‐BN) threshold memristors with two nickel (Ni) electrodes is investigated through their current conduction mechanisms. Both the high and the low resistance states are analyzed through temperature‐dependent current–voltage measurements. The formation and retraction of nickel filaments along boron defects in the h‐BN film as the resistive switching mechanism is proposed. The electrical data are corroborated with TEM analyses to establish temperature‐dependent current–voltage measurements as a valuable tool for the analysis of resistive switching phenomena in memristors made of 2D materials. The memristors exhibit a wide and tunable current operation range and low stand‐by currents, in line with the state of the art in h‐BN‐based threshold switches, a low cycle‐to‐cycle variability of 5%, and a large On/Off ratio of 107.
- 5 May 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 34 (15)
Open AccessResistive Switching and Current Conduction Mechanisms in Hexagonal Boron Nitride Threshold Memristors with Nickel Electrodes
The 2D insulating material hexagonal boron nitride (h‐BN) has attracted much attention as the active medium in memristive devices due to its favorable physical properties, among others, a wide bandgap that enables a large switching window. Metal filament formation is frequently suggested for h‐BN devices as the resistive switching (RS) mechanism, usually supported by highly specialized methods like conductive atomic force microscopy (C‐AFM) or transmission electron microscopy (TEM). Here, the switching of multilayer hexagonal boron nitride (h‐BN) threshold memristors with two nickel (Ni) electrodes is investigated through their current conduction mechanisms. Both the high and the low resistance states are analyzed through temperature‐dependent current–voltage measurements. The formation and retraction of nickel filaments along boron defects in the h‐BN film as the resistive switching mechanism is proposed. The electrical data are corroborated with TEM analyses to establish temperature‐dependent current–voltage measurements as a valuable tool for the analysis of resistive switching phenomena in memristors made of 2D materials. The memristors exhibit a wide and tunable current operation range and low stand‐by currents, in line with the state of the art in h‐BN‐based threshold switches, a low cycle‐to‐cycle variability of 5%, and a large On/Off ratio of 107.