Aybars Mahmat
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Aybars Mahmat has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Nihat Tosun
Firat Universitesi
8 shared publications - Salih Ağar
Munzur Üniversitesi
8 shared publications - Akar Dogan
Department of Mechanical Engineering Munzur University Faculty of Engineering Tunceli Türkiye
2 shared publications - Gul Tosun
Firat Universitesi
2 shared publications - Gürkan Doğan
Munzur Üniversitesi
2 shared publications Aras Dalgıç
Department of Mechanical Engineering, Munzur University, Tunceli, Turkey
1 shared publication
Latest Publications
- 30 September 2026
- Published by Firat Universitesi in Fırat Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 38 (2) , 765-782
Ti6AI7Nb Alaşımının Mikro Frezelenmesinde Kesme Kuvvetinin Öngörülmesi için Yenilikçi Hibrit Derin Sinir Ağı Modeli
Titanyum alaşımları, yüksek mukavemet-ağırlık oranları, korozyon dirençleri ve biyouyumlulukları sayesinde havacılıktan savunmaya, biyomedikalden uzay teknolojilerine kadar pek çok kritik alanda vazgeçilmez malzemeler haline gelmiştir. Ancak bu alaşımlar, düşük ısıl iletkenlik ve yüksek kimyasal reaktivite gibi özellikleri nedeniyle işlenmesi güç malzemeler olarak bilinmektedir. Bu durum, özellikle, kesme kuvveti, takım ömrünü, boyutsal hassasiyeti ve iş parçası bütünlüğünü doğrudan etkileyen temel bir parametre olmasından dolayı kesme kuvvetinin doğru tahmin edilmesini hem teknik açıdan zorlaştırmakta hem de süreç güvenilirliği açısından zorunlu kılmaktadır. Bu çalışmada, Ti6AI7Nb alaşımının mikro frezelenmesi sürecinde kesme kuvvetinin yüksek doğrulukla tahmin edilmesine yönelik yeni bir hibrit derin sinir ağı modeli önerilmektedir. Önerilen modelde, evrişimli sinir ağı katmanı ile veriden anlamlı yerel özellikler otomatik olarak çıkarılırken, bu katmana paralel olarak konumlandırılan tam bağlantılı katmanlarda karmaşık ilişkileri ve küresel bilgileri çıkarmak üzere entegre edilmiştir. Önerilen model ve güncel yöntemlerin eğitimi ve testi için kısıtlı olan gerçek deneysel veriler, veri artırma tekniğiyle çoğaltılarak sentetik veriler üretilmiştir. Gerçekleştirilen kapsamlı analizlerde, önerilen paralel hibrit derin öğrenme modelinin kesme kuvveti tahmininde %97.13 R² skoru ile geleneksel makine öğrenmesi yöntemlerinden daha yüksek performans sergilediği ortaya koyulmuştur.
- 30 September 2026
- Published by Firat Universitesi in Fırat Üniversitesi Mühendislik Bilimleri Dergisi
- Vol. 38 (2) , 765-782
Ti6AI7Nb Alaşımının Mikro Frezelenmesinde Kesme Kuvvetinin Öngörülmesi için Yenilikçi Hibrit Derin Sinir Ağı Modeli
Titanyum alaşımları, yüksek mukavemet-ağırlık oranları, korozyon dirençleri ve biyouyumlulukları sayesinde havacılıktan savunmaya, biyomedikalden uzay teknolojilerine kadar pek çok kritik alanda vazgeçilmez malzemeler haline gelmiştir. Ancak bu alaşımlar, düşük ısıl iletkenlik ve yüksek kimyasal reaktivite gibi özellikleri nedeniyle işlenmesi güç malzemeler olarak bilinmektedir. Bu durum, özellikle, kesme kuvveti, takım ömrünü, boyutsal hassasiyeti ve iş parçası bütünlüğünü doğrudan etkileyen temel bir parametre olmasından dolayı kesme kuvvetinin doğru tahmin edilmesini hem teknik açıdan zorlaştırmakta hem de süreç güvenilirliği açısından zorunlu kılmaktadır. Bu çalışmada, Ti6AI7Nb alaşımının mikro frezelenmesi sürecinde kesme kuvvetinin yüksek doğrulukla tahmin edilmesine yönelik yeni bir hibrit derin sinir ağı modeli önerilmektedir. Önerilen modelde, evrişimli sinir ağı katmanı ile veriden anlamlı yerel özellikler otomatik olarak çıkarılırken, bu katmana paralel olarak konumlandırılan tam bağlantılı katmanlarda karmaşık ilişkileri ve küresel bilgileri çıkarmak üzere entegre edilmiştir. Önerilen model ve güncel yöntemlerin eğitimi ve testi için kısıtlı olan gerçek deneysel veriler, veri artırma tekniğiyle çoğaltılarak sentetik veriler üretilmiştir. Gerçekleştirilen kapsamlı analizlerde, önerilen paralel hibrit derin öğrenme modelinin kesme kuvveti tahmininde %97.13 R² skoru ile geleneksel makine öğrenmesi yöntemlerinden daha yüksek performans sergilediği ortaya koyulmuştur.
- 9 April 2026
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 40 (4) , 2837-2845
Investigation of the effect of ultrasonic assisted milling and minimum quantity lubrication methods on the machinability of Hardox 500 steel
- 9 April 2026
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 40 (4) , 2837-2845
Investigation of the effect of ultrasonic assisted milling and minimum quantity lubrication methods on the machinability of Hardox 500 steel
- 15 September 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (19) , 22873-22881
Investigation of Mechanical Properties of Jute and Tea Waste-Reinforced Epoxy Composite Material Produced by Vacuum Assisted Resin Infusion Molding
- 15 September 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (19) , 22873-22881
Investigation of Mechanical Properties of Jute and Tea Waste-Reinforced Epoxy Composite Material Produced by Vacuum Assisted Resin Infusion Molding
- 13 March 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 239 (12) , 4581-4592
Modeling and analysis of WEDM with a new deep neural network
In some cases, the models targeted in machining processes are difficult to apply to industrial production. Artificial intelligence techniques applied to industrial production methods in recent times eliminate these problems in machining. The use of deep learning methods in solving these problems has recently increased. In this study, a new deep neural network (DNN) based on artificial neural networks is proposed to model the machining of AISI4140 steel by wire electrical discharge machining (WEDM). The proposed DNN model predicts surface roughness (SR) and wire wear ratio (WWR), which are the most important inferences in cutting with WEDM. Obtaining inferences such as SR and WWR in a real experimental environment means a lot of time and cost. With the proposed model, there is a significant reduction in time and cost factors. The dataset used to train and test the proposed model was obtained from the real experimental environment. For training and testing the model, the data set is divided into two parts: 20% test data and 80% training data. In the experimental tests carried out with the proposed model, error rates such as Mean Absolute Error (MAE), R 2 , and Mean Squared Error (MSE) accuracy rate between SR and WWR values estimated according to the SR and WWR values obtained from the real environment were examined. MAE, MSE, and R 2 for SR reached 0.0495, 0.0005, and 98.48%, respectively, while MAE, MSE, and R 2 for WWR reached 0.0156, 0.0036, and 98.39%, respectively. These results of the proposed model provided a lower error rate and higher accuracy than the state-of-the-art models in the literature.
- 13 March 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 239 (12) , 4581-4592
Modeling and analysis of WEDM with a new deep neural network
In some cases, the models targeted in machining processes are difficult to apply to industrial production. Artificial intelligence techniques applied to industrial production methods in recent times eliminate these problems in machining. The use of deep learning methods in solving these problems has recently increased. In this study, a new deep neural network (DNN) based on artificial neural networks is proposed to model the machining of AISI4140 steel by wire electrical discharge machining (WEDM). The proposed DNN model predicts surface roughness (SR) and wire wear ratio (WWR), which are the most important inferences in cutting with WEDM. Obtaining inferences such as SR and WWR in a real experimental environment means a lot of time and cost. With the proposed model, there is a significant reduction in time and cost factors. The dataset used to train and test the proposed model was obtained from the real experimental environment. For training and testing the model, the data set is divided into two parts: 20% test data and 80% training data. In the experimental tests carried out with the proposed model, error rates such as Mean Absolute Error (MAE), R 2 , and Mean Squared Error (MSE) accuracy rate between SR and WWR values estimated according to the SR and WWR values obtained from the real environment were examined. MAE, MSE, and R 2 for SR reached 0.0495, 0.0005, and 98.48%, respectively, while MAE, MSE, and R 2 for WWR reached 0.0156, 0.0036, and 98.39%, respectively. These results of the proposed model provided a lower error rate and higher accuracy than the state-of-the-art models in the literature.
- 27 January 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 239 (10) , 3751-3759
Experimental comparison of conventional and ultrasonic-assisted high-speed drilling of glass fiber reinforced epoxy composites
Glass fiber reinforced epoxy composites are favored in several industries, including automotive and aerospace, owing to their superior strength-to-weight ratio. Drilling is a prevalent machining procedure employed to add fasteners for laminate assembly. Nonetheless, drilling these composites presents significant challenges due to the abrasive characteristics of the reinforcement, necessitating an examination of machining performance. During the drilling of composites, cutting temperature, thrust force, and delamination damage are primary concerns. In recent years, high-speed ultrasonic drilling, an innovative machining technique designed to address these challenges, has garnered significant interest. This investigation involved high-speed ultrasonic drilling and conventional drilling of glass fiber reinforced epoxy material. In the studies, optimal conditions were studied by evaluating thrust force, cutting temperature, and delamination damage by varying speeds, feed rates, and frequencies. The thrust force was 11 N in the traditional approach at 40,000 rpm, but it was recorded at 9 N with the ultrasonic method. Moreover, with ultrasonic drilling, cutting temperatures decreased by over 25% relative to traditional drilling, attributable to the harmonic motion that dissipates heat in the drilling zone. Analysis of the drilling region revealed a notable enhancement in damage, particularly in delamination, with the application of ultrasonic drilling. The experimental results indicate that ultrasonic machining enhances machining performance.
- 27 January 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 239 (10) , 3751-3759
Experimental comparison of conventional and ultrasonic-assisted high-speed drilling of glass fiber reinforced epoxy composites
Glass fiber reinforced epoxy composites are favored in several industries, including automotive and aerospace, owing to their superior strength-to-weight ratio. Drilling is a prevalent machining procedure employed to add fasteners for laminate assembly. Nonetheless, drilling these composites presents significant challenges due to the abrasive characteristics of the reinforcement, necessitating an examination of machining performance. During the drilling of composites, cutting temperature, thrust force, and delamination damage are primary concerns. In recent years, high-speed ultrasonic drilling, an innovative machining technique designed to address these challenges, has garnered significant interest. This investigation involved high-speed ultrasonic drilling and conventional drilling of glass fiber reinforced epoxy material. In the studies, optimal conditions were studied by evaluating thrust force, cutting temperature, and delamination damage by varying speeds, feed rates, and frequencies. The thrust force was 11 N in the traditional approach at 40,000 rpm, but it was recorded at 9 N with the ultrasonic method. Moreover, with ultrasonic drilling, cutting temperatures decreased by over 25% relative to traditional drilling, attributable to the harmonic motion that dissipates heat in the drilling zone. Analysis of the drilling region revealed a notable enhancement in damage, particularly in delamination, with the application of ultrasonic drilling. The experimental results indicate that ultrasonic machining enhances machining performance.
- Open Access
- 31 December 2024
- Published by International Journal of Pure and Applied Sciences in International Journal of Pure and Applied Sciences
- Vol. 10 (2) , 407-417
Hardox 500 Çeliğinin Delinmesinde Minimum Miktarda Yağlama Yönteminin Yüzey Pürüzlülüğü ve Kesme Sıcaklığına Olan Etkisinin İncelenmesi
Hardox 500 aşınma ve kırılmalara karşı dirençli, yüksek sertlik ve mekanik muka-vemete sahip sertleştirilmiş bir çeliktir. Bu yüksek mekanik özellikler bu malzemenin işlenebilirliğini sınırlamaktadır. Bu çalışmanın amacı işlenmesi zor olan Hardox 500 çeliğine farklı soğutma yöntemleri ve işleme parametrelerinin uygulanmasıyla işle-nebilirliğini artırmaktır. Endüstriyel açıdan önemli bir malzeme olan Hardox 500 çeliğinin çeşitli kesme ortamları kullanılarak işlenebilirliğini artırmak amaçlanmış-tır. Farklı ilerleme hızları, kesme hızları ve soğutma yöntemlerinin yüzey pürüzlü-lüğüne, kesme sıcaklıklarına, takım aşınmasına olan etkisi incelenmiştir. Deneysel sonuçlara göre Minimum miktarda yağlama (MMY) yöntemi yüzey kalitesini artır-dığı ve yan yüzey aşınması ile kesme sıcaklıklarını düşürdüğü görülmüştür. Kuru koşullara göre MMY yöntemi kullanılarak yüzey pürüzlülüğünde yaklaşık %20-30, kesme sıcaklığında yaklaşık %15-35 yan yüzey aşınmasında %22-30 oranında iyi-leşme elde edilmiştir. Yüzey kalitesini optimize etmek için yüksek kesme hızı ve düşük ilerleme hızlarının seçilmesi gerektiği görülmüştür. Yüksek kesme hızı ve ilerleme hızı sürtünmeyi artırarak sıcaklığı artırmıştır.
- 31 December 2024
- Published by International Journal of Pure and Applied Sciences in International Journal of Pure and Applied Sciences
- Vol. 10 (2) , 407-417
Open AccessHardox 500 Çeliğinin Delinmesinde Minimum Miktarda Yağlama Yönteminin Yüzey Pürüzlülüğü ve Kesme Sıcaklığına Olan Etkisinin İncelenmesi
Hardox 500 aşınma ve kırılmalara karşı dirençli, yüksek sertlik ve mekanik muka-vemete sahip sertleştirilmiş bir çeliktir. Bu yüksek mekanik özellikler bu malzemenin işlenebilirliğini sınırlamaktadır. Bu çalışmanın amacı işlenmesi zor olan Hardox 500 çeliğine farklı soğutma yöntemleri ve işleme parametrelerinin uygulanmasıyla işle-nebilirliğini artırmaktır. Endüstriyel açıdan önemli bir malzeme olan Hardox 500 çeliğinin çeşitli kesme ortamları kullanılarak işlenebilirliğini artırmak amaçlanmış-tır. Farklı ilerleme hızları, kesme hızları ve soğutma yöntemlerinin yüzey pürüzlü-lüğüne, kesme sıcaklıklarına, takım aşınmasına olan etkisi incelenmiştir. Deneysel sonuçlara göre Minimum miktarda yağlama (MMY) yöntemi yüzey kalitesini artır-dığı ve yan yüzey aşınması ile kesme sıcaklıklarını düşürdüğü görülmüştür. Kuru koşullara göre MMY yöntemi kullanılarak yüzey pürüzlülüğünde yaklaşık %20-30, kesme sıcaklığında yaklaşık %15-35 yan yüzey aşınmasında %22-30 oranında iyi-leşme elde edilmiştir. Yüzey kalitesini optimize etmek için yüksek kesme hızı ve düşük ilerleme hızlarının seçilmesi gerektiği görülmüştür. Yüksek kesme hızı ve ilerleme hızı sürtünmeyi artırarak sıcaklığı artırmıştır.
- 31 December 2024
- Published by International Journal of Innovative Engineering Applications in International Journal of Innovative Engineering Applications
- Vol. 8 (2) , 82-88
INVESTIGATION OF TOOL WEAR AND THRUST FORCE IN DRILLING AISI 316 AUSTENITIC STAINLESS STEEL USING ELECTROPHORESIS METHOD
Cutting tool costs are an important component of machining. For this reason, improving machining methods in machining affects the life of the cutting tool. Recently, various machining methods have been used to extend tool life by reducing cutting tool wear. One of these methods is electrophoresis-assisted processing. Electrophoresis-assisted machining is a non-traditional machining method created by the impact of abrasive nanoparticles on the machining area with the help of the generated electric field. Electrophoresis-assisted machining increases the machinability of difficult-to-machine materials with high strength and hardness properties compared to traditional machining methods. In this study, the impacts of various cutting parameters on the drilling performance of AISI 316 L stainless steel material were searched using electrophoresis-assisted drilling (EAD) and conventional drilling (CD) methods. In the study, SiC powder was used as nanoparticles in the solution obtained to create the electric field. Within the scope of the experiments, the effects of different machining methods, cutting speeds and feed rates on thrust forces and cutting tool wear values were experimentally examined. As a result of the investigations, the cutting tool wear and thrust cutting force obtained with EAD are better than CM. Increasing feed rate and cutting speed increased cutting tool wear in both machining methods. It has been determined that the thrust force decreases as the cutting speed increases, while it increases as the feed rate increases.Keywords: Electrophoresis, drilling, cutting force, tool wear, AISI 316
- 31 December 2024
- Published by International Journal of Innovative Engineering Applications in International Journal of Innovative Engineering Applications
- Vol. 8 (2) , 82-88
INVESTIGATION OF TOOL WEAR AND THRUST FORCE IN DRILLING AISI 316 AUSTENITIC STAINLESS STEEL USING ELECTROPHORESIS METHOD
Cutting tool costs are an important component of machining. For this reason, improving machining methods in machining affects the life of the cutting tool. Recently, various machining methods have been used to extend tool life by reducing cutting tool wear. One of these methods is electrophoresis-assisted processing. Electrophoresis-assisted machining is a non-traditional machining method created by the impact of abrasive nanoparticles on the machining area with the help of the generated electric field. Electrophoresis-assisted machining increases the machinability of difficult-to-machine materials with high strength and hardness properties compared to traditional machining methods. In this study, the impacts of various cutting parameters on the drilling performance of AISI 316 L stainless steel material were searched using electrophoresis-assisted drilling (EAD) and conventional drilling (CD) methods. In the study, SiC powder was used as nanoparticles in the solution obtained to create the electric field. Within the scope of the experiments, the effects of different machining methods, cutting speeds and feed rates on thrust forces and cutting tool wear values were experimentally examined. As a result of the investigations, the cutting tool wear and thrust cutting force obtained with EAD are better than CM. Increasing feed rate and cutting speed increased cutting tool wear in both machining methods. It has been determined that the thrust force decreases as the cutting speed increases, while it increases as the feed rate increases.Keywords: Electrophoresis, drilling, cutting force, tool wear, AISI 316
- 27 December 2024
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 47 (1) , 1-14
Ultrasonic-assisted high-speed micro-milling of Ti6Al4V
- 27 December 2024
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 47 (1) , 1-14
Ultrasonic-assisted high-speed micro-milling of Ti6Al4V
- Open Access
- 24 October 2024
- Published by Elsevier in Engineering Science and Technology, an International Journal
- Vol. 59
Investigation of the effect of electrophoresis-assisted milling on machinability
- 24 October 2024
- Published by Elsevier in Engineering Science and Technology, an International Journal
- Vol. 59
Open AccessInvestigation of the effect of electrophoresis-assisted milling on machinability
- 30 December 2023
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 31 (07)
ENHANCING MILLING PERFORMANCE OF 6061 ALUMINUM ALLOY WITH NANOCUTTING FLUID AND MQL
During the machining of aluminum alloys, the adhesion of chips to the tool affects the performance characteristics. Today, different cooling systems are used to eliminate these negativities. In this study, the effects of end milling using HSS and carbide cutting tools of 6061-T6 aluminum alloy on surface roughness, chip thickness ratio and tool wear were examined using different cooling techniques (dry, minimum quantity lubrication (MQL) and nanocutting fluid). Different cutting speeds (180, 200, 220 m/min) and different feed rates (0.05, 0.06, 0.07 mm/rev) were used in the experiments. According to experimental findings, tool wear and surface roughness decreased at low cutting speed and feed rate by using nanocutting fluid with carbide cutting tools. It has been observed that the chip thickness ratio increases with high cutting speeds using nanocutting fluid and decreases with dry machining and high feed rates. The best milling performance of the aluminum alloy was achieved in experiments using carbide cutting tools and nanocutting fluid.
- 30 December 2023
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 31 (07)
ENHANCING MILLING PERFORMANCE OF 6061 ALUMINUM ALLOY WITH NANOCUTTING FLUID AND MQL
During the machining of aluminum alloys, the adhesion of chips to the tool affects the performance characteristics. Today, different cooling systems are used to eliminate these negativities. In this study, the effects of end milling using HSS and carbide cutting tools of 6061-T6 aluminum alloy on surface roughness, chip thickness ratio and tool wear were examined using different cooling techniques (dry, minimum quantity lubrication (MQL) and nanocutting fluid). Different cutting speeds (180, 200, 220 m/min) and different feed rates (0.05, 0.06, 0.07 mm/rev) were used in the experiments. According to experimental findings, tool wear and surface roughness decreased at low cutting speed and feed rate by using nanocutting fluid with carbide cutting tools. It has been observed that the chip thickness ratio increases with high cutting speeds using nanocutting fluid and decreases with dry machining and high feed rates. The best milling performance of the aluminum alloy was achieved in experiments using carbide cutting tools and nanocutting fluid.